JETWAY TA77AG Manual de usuario

USER'S MANUAL

for

AMD 770 & AMD SB710

Based

Motherboard Series

Trademark:

* Specifications and information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

NO. G03-TA77AG-F

Rev

：

1.0

Release in: September, 2011

Environmental Safety Instruction

zAvoid the dusty, humidity and temperature extremes. Do not place the product in any

area where it may become wet.

z0 to 40 centigrade is the suitable temperature. (The figure comes from the request of

the main chipset)

zGenerally speaking, dramatic changes in temperature may lead to contact malfunction

and crackles due to constant thermal expansion and contraction from the welding

spots’ that connect components and PCB. Computer should go through an adaptive

phase before it boots when it is moved from a cold environment to a warmer one to

avoid condensation phenomenon. These water drops attached on PCB or the surface

of the components can bring about phenomena as minor as computer instability

resulted from corrosion and oxidation from components and PCB or as major as short

circuit that can burn the components. Suggest starting the computer until the

temperature goes up.

zThe increasing temperature of the capacitor may decrease the life of computer. Using

the close case may decrease the life of other device because the higher temperature in

the inner of the case.

zAttention to the heat sink when you over-clocking. The higher temperature may

decrease the life of the device and burned the capacitor.

Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. To minimize pollution

and ensure environment protection of mother earth, please recycle.

CHAPTER 1 INTRODUCTION OF AMD 770 MOTHERBOARDS

1-1 FEATURES OF MOTHERBOARD................................................................1

1-1-1 SPECIAL FEATURES OF MOTHERBOARD .................................2

1-2 ITEM CHECKLIST.........................................................................................3

1-3 SPECIFICATION...........................................................................................3

1-4 LAYOUT DIAGRAM......................................................................................4

CHAPTER 2 HARDWARE INSTALLATION

2-1 HARDWARE INSTALLATION STEPS .........................................................6

2-2 JUMPER SETTING .....................................................................................6

2-3 CPU INSTALLATION ..................................................................................7

2-4 MEMORY INSTALLATION .........................................................................8

2-5 EXPASION CARD INSTALLATION .............................................................9

2-5-1 EXPASION SLOTS .........................................................................9

2-5-2 PROCEDURE FOR EXPASION CARD INSTALLATION...............9

CHAPTER 3 CONNCTORS & HEADERS

3-1 I/O BACK PANEL CONNECTORS...............................................................10

3-2 INTERNAL CONNECTORS..........................................................................10

3-3 INTERNAL HEADERS..................................................................................13

CHAPTER 4 USEFUL HELP

4-1 HOW TO UPDATE BIOS ..............................................................................15

4-2 TROUBLE SHOOTING .................................................................................15

APPENDIX...................................................................................................................16

TABLE OF CONTENT

Chapter 1

Introduction of AMD 770 Motherboards

1-1 Features of motherboard

The AMD 770 chipset motherboard series are based on the latest AMD 770 Chipset

and the SB 710 chipset with a highly-scalable Hyper Transport technology-based

system bus up to HT 3.0; AMD 770 Platform Processor Chipset motherboard series

deliver the outstanding system performance and professional desktop platform

solution.

The AMD 770 Series motherboards support four dual channel DDRIII 800/ DDRIII

1066/DDRIII 1333 modules up to 8GB; These motherboards are embedded with

SB710 chipset which support up to four SATA2.0 devices with RAID 0, 1, 10, JBOD

functions to accelerate hard disk drives and guarantee the data security without failure

in advanced computing performance.

The AMD 770 Series motherboards provide gigabit PCI-E LAN chip which supports

10/100/1000 Mbps data transfer rate. The AMD 770 Series motherboards are

embedded with 6-channel HD Audio CODEC fully compatible with Sound Blaster Pro

standards that offer you with the home cinema quality and satisfying software

compatibility.

The AMD 770 Series motherboards offer one PCI-Express x16 graphics slot and two

PCI-E x1 slots. The AMD 770 motherboards also carry two 32-bit PCI slots to

guarantee the rich connectivity for the I/O peripheral devices.

Embedded USB controllers as well as capability of expanding to 10 of USB2.0

functional ports delivering 480Mb/s bandwidth, these motherboards meet the future

USB demands which are also equipped with hardware monitor function on system to

monitor and protect your system and maintain your non-stop business computing.

Some special features--- CPU Thermal Throttling/CPU VID/ CPU Vcore OC-CON in

this motherboard are designed for power user to use the over-clocking function in

more flexible ways. But please be caution that the over-clocking maybe causes the

fails in system reliabilities. This motherboard provides the guaranteed performance

and meets the demands of the next generation computing. But if you insist to gain

more system performance with variety possibilities of the components you choose,

please be careful and make sure to read the detailed descriptions of these value

added product features, please get them in the coming section.

1-1.1 Special Features of Motherboard

CPU Thermal Throttling Technology (The CPU Overheat Protection Technology)

To prevent the increasing heat from damage of CPU or accidental shutdown while at

high workload, the CPU Thermal Throttling Technology will force CPU to enter

partially idle mode from 87.5% to 12.5% according to preset CPU operating

temperature in BIOS (from 40 to 90 ). When the system senses the CPU℃℃

operating temperature reaching the preset value, the CPU operating bandwidth will be

decreased to the preset idle percentage to cool down the processor. When at

throttling mode the beeper sound can be optionally selected to indicate it is in working.

CPU VID---Shift to Higher Performance

The CPU voltage can be adjusted for the precisely over-clocking of extra demanding

computing performance.

CPU Vcore Input & Output OC-CON (High-polymer Solid Electrolysis Aluminum

Capacitors)

CPU Vcore Input and Output adopt OC-CON solid capacitors. OC-CON solid

capacitors make it possible for motherboard to work from 55 degrees Centigrade

below zero to 125 degrees centigrade. OC-CON capacitors possess superior physical

characteristics to prolong product life ten times than corresponding motherboard

without capacitors every time working temperature increases 20 degrees. Life of

product of motherboard with solid capacitors declines only 10% of those without solid

capacitors as well under same conditions.

1-2 Item Checklist

•Motherboard

•DVD for motherboard utilities

•User’s manual

•I/O back panel

•Hard disk cable

1-3 Specification

Spec Description

Design zATX form factor; Size:29.5 x19.0 cm

Chipset zAMD 770 North Bridge Chipset

zAMD SB710 South Bridge Chipset

AM2 CPU Socket

(Optional model) zAMD AM2 Socket

zSupport AMD AM3 Phenom™ II processor/Athlon™ II

series processor

zCPU power consumption should be under 125W

* for detailed CPU support information please visit our website

AM3+ CPU Socket

(Optional Model)

zAMD AM3+ Socket

zSupport AMD AM3+ FX processors and AMD AM3

Phenom™ II processor/Athlon™ II series processor

zCPU power consumption should be under 125W

zSupport HT 3.0

* for detailed CPU support information please visit our website

Memory Slot

z240-pin DDRIII Module slot x 2

zSupport 2pcs DDRIII 800/1066/1333 memory modules

expandable to 8 GB

zDual channel supported

Expansion Slot

z1 pcs *PCI-Express 2.0 x16 by 16 lane slot

z2 pcs *PCI-Express 2.0 x1 slots

z2 pcs * 32-bit PCI slots

SATA2 Ports RAID zSupports four SATAII devices providing 3.0 Gb/sec data

transfer rate and support RAID 0,1, 10,JBOD

Gigabit LAN Chip

zIntegrated PCI-E gigabit LAN chip

zSupport Fast Ethernet LAN function of providing

10Mb/100Mb/1000 Mb/s data transfer rate

6-CH Audio z6-channel HD Audio Codec integrated

zAudio driver and utility included

BIOS z8MB Flash ROM BIOS

Multi I/O

zPS/2 keyboard & mouse port x1

zCoaxial SPDIF_OUT port x1

zUSB 2.0 port x 2 and USB 2.0 port x2

zRJ-45 LAN Connector x1

zAudio connector x1

zFront panel audio header x1

zHDMI_SPDIF header x1

zSerial port header x1

zFront panel header x1

zPower LED header x1

zSpeaker header x 1

1-4 Layout Diagram

For model with AM2 CPU Socket:

CPU Socket

ATX Power Conn.

CPU FAN1 Header

Front Panel

Audio Header

USB Headers

SYSFAN1

Header

ATX 12V

Power Connector

Line-IN

MIC-IN

PS/2 Keyboard

Port

Coaxial S/PDIF out

Port

DDRIII Slot x 2

JBAT

SATAII Connecto

(SATA 1, 2, 3, 4)

Audio Connector

COM Header

PCI Express 2.0 x16 by 16 Lane slot

Line-OUT

KB/MS Power on (JP1)

6-CH HD Audio Chip

HDMI-SPDIF

Header

Front Panel Header

PCI Express 2.0 x1 slots

Gigabit LAN Chip

Coaxial S/PDIF

Out port

Power LED Header

Speaker Header

USB Ports

RJ-45 LAN Port

RJ-45 over

USB

orts

PS/2 Mouse

Port

PS/2 MS over

PS/2 KB port

USB ports

AMD 770 Chipset

AMD SB 710 Chipset

PCI Slot

ATA 133 IDE

Conn. (IDE1)

For model with AM3+ CPU Socket:

Notice:

1. The above models have basically same layout, except that one is embedded

with AM2 CPU socket and the other with AM3+ CPU socket. Due to the

difference in CPU socket, these two models support different range of

compatible CPU.

2. For illustration purpose, the photos in this manual are from the model with AM3+

CPU socket, unless otherwise stated.

AM3

CPU Socket

ATX Power Conn.

CPU FAN1 Header

Front Panel

Audio Header

USB Headers

SYSFAN1

Header

ATX 12V

Power Connector

DDRIII Slot x 2

JBAT

SATAII Connecto

(SATA 1, 2, 3, 4)

Audio Connector

COM Header

PCI Express 2.0 x16 by 16 Lane slot

KB/MS Power on (JP1)

6-CH HD Audio Chip

HDMI-SPDIF

Header

Front Panel Header

PCI Express 2.0 x1 slots

Gigabit LAN Chip

Coaxial S/PDIF

Out port

Power LED Header

Speaker Header

RJ-45 over

USB

orts

PS/2 MS over

PS/2 KB port

USB ports

AMD 770 Chipset

AMD SB 710 Chipset

PCI Slot

ATA 133 IDE

Conn. (IDE1)

SYSFAN2

Header

Chapter 2

Hardware Installation

WARNING! Turn off your power when adding or removing expansion cards or

other system components. Failure to do so may cause severe

damage to both your motherboard and expansion cards.

2-1 Hardware Installation Steps

Before using your computer, you had better complete the following steps:

1. Check motherboard jumper setting

2. Install CPU and Fan

3. Install System Memory (DIMM)

4. Install Expansion cards

5. Connect hard disk and front panel /back panel cable

6. Connect ATX Power cable

7. Power-On and Load Standard Default

8. Reboot

9. Install Operating System

10. Install Driver and Utility

2-2 Jumper Setting

(1) CMOS RAM Clear (3-pin): JBAT1

A battery must be used to retain the motherboard configuration in CMOS RAM

short 1-2 pins of JBAT to store the CMOS data.

To clear the CMOS, follow the procedure below:

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from ATX power connector.

3. Locate JBAT and short pins 2-3 for a few seconds.

4. Return JBAT to its normal setting by shorting pins 1-2.

5. Connect ATX power cable back to ATX power connector.

Note: When should clear CMOS

1. Troubleshooting

2. Forget password

3. After over clocking system boot fail

CMOS RAM Clear Setting

2-3 Closed: Clear CMOS

JBATJBAT

1-2 Closed: Normal

(2) KB/USB Power on Function Enabled/Disabled: JP1

KB/USB Power On Setting

2-3 Closed: KB/USB Power ON Enabled

JP1

1-2 Closed: KB/USB Power ON Disable (Default)

2-3 CPU Installation

This motherboard provides a surface mount, Zero Insertion Force (ZIF) CPU socket.

Depending on the model you selected, there are two type of CPU socket available for

this motherboard series. One model comes with AMD AM2 CPU socket, and the other

comes with AMD AM3+ CPU socket. They support different range of AMD CPU

(please visit our website for detailed CPU support list or consult your dealer).

The installation steps are basically the same. Please refer to the following CPU

installation guide.

To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket

and open it by first pulling the level sideways away from the socket then upward to a

90-degree angle. Insert the CPU with the correct orientation as shown below. The

notched corner should point toward the end of the level. Because the CPU has a

corner pin for two of the four corners, the CPU will only fit in the orientation as shown.

CPU ZIF mPGAB Socket

Colden Arrow

CPU Socket

When you put the CPU into the ZIF socket, no force required to insert of the CPU, and

then press the level to locate position slightly without any extra force.

The CPU that comes with the motherboard should have a cooling FAN attached to

prevent overheating. If this is not the case, then purchase a correct cooling FAN

before you turn on your system.

WARNING! Be sure that there is sufficient air circulation across the processor’s

heat sink and CPU cooling FAN is working correctly, otherwise it

may cause the processor and motherboard overheat and damage,

you may install an auxiliary cooling FAN, if necessary.

Tabla de contenidos

Otros manuales de Placa madre de JETWAY

JETWAY

JETWAY 615TCFR3A Manual de usuario

JETWAY

JETWAY 613CN Manual de usuario

JETWAY

JETWAY 875PMAXR2A Manual de usuario

JETWAY

JETWAY 618AFP2A Manual de usuario

JETWAY

JETWAY 650EM Manual de usuario

JETWAY

JETWAY 848PDAR1A Manual de usuario

JETWAY

JETWAY 865GDA Manual de usuario

JETWAY

JETWAY 939TURBOR208 Manual de usuario

JETWAY

JETWAY XBLUE77A3 Manual de usuario

JETWAY

JETWAY NF697 Series Manual de usuario

JETWAY

JETWAY NC9S-B85 Manual de usuario

JETWAY

JETWAY P4X40DAR2A Manual de usuario

JETWAY

JETWAY NMF91 Series Manual de usuario

JETWAY

JETWAY 694TAS3A Manual de usuario

JETWAY

JETWAY 830CN Manual de usuario

JETWAY

JETWAY MI215 Series Manual de usuario

JETWAY

JETWAY ALIOTH Manual de usuario

JETWAY

JETWAY NF835A Series Manual de usuario

JETWAY

JETWAY NC9L Manual de usuario

JETWAY

JETWAY 845GVFC Manual de usuario

JETWAY

JETWAY NLBT-I1900 Series Manual de usuario

JETWAY

JETWAY V4MDFTR1A Manual de usuario

JETWAY

JETWAY 603TCR1C Manual de usuario

JETWAY

JETWAY 866ASR2C Manual

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario