Jetta Baths Guía de solución de problemas
www.jettacorp.com
Owner’s Manual &
Installation Guide
This manual is to be given to the product owner and should be kept for future use.
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
2
Table of Contents
FACTS THAT MAKE JETTA YOUR BEST CHOICE.......................................4
SAFETY INSTRUCTIONS ....................................................................................5
INSTALLATION INSTRUCTIONS....................................................................6
INSTALLATION INSTRUCTIONS - optional skirt ................................7
MAINTENANCE & CLEANING.........................................................................8
OPERATING INSTRUCTIONS - CLASSIC SERIES ......................................9
OPERATING INSTRUCTIONS - DESIGNER/ELITE SERIES ....................10
OPERATING INSTRUCTIONS - OPTIONAL AIR BATH ...........................11
TROUBLESHOOTING..........................................................................................13
LIMITED FACTORY WARRANTY.....................................................................14
3
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
Lean back and escape into the warmth of your new Jetta bath with the
condence that you have made the right choice.
Jetta whirlpool baths have unique features that are not found in any
other whirlpool bath. We have mastered the ergonomics of body comfort and
perfect jet placement, giving you luxury at a reasonable price. Our
passive warm air induction systems and totally insulated whirlpools allow us to
provide our exclusive Jetta Stay Hot Guarantee. We guarantee the water
temperature will stay within 2 degrees of its original temperature after 30 minutes
of use. This insulation also means that distractive motor noises and vibrations are
virtually eliminated, allowing you to escape from the world a little bit longer.
In this manual, you will nd the information that you will need to install and
operate your new bath. If you have any additional questions regarding your
tub, feel free to call us at 1-800-288-7771, and we’ll be happy to answer your
questions.
Thank you for choosing Jetta.
Date Purchased: __________________________________________
Purchased From: __________________________________________
Serial #: ________________________________________________
Model #: ________________________________________________
Manufacturer’s Date: _______________________________________
Installed By: _____________________________________________
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
4
owner’s manual
facts that make jetta your best choice
Jetta Bath Systems are available in a wide variety of shapes, sizes, and jet congurations with several premium •
models available and offers the ultimate in hydrotherapy and relaxation. Jetta has mastered the ergonomics
of body comfort and jet placement and includes built in arm, foot and head rests as well as lumbar support for
maximum comfort.
Made with the highest quality materials and manufactured to ANSI and ASME standards, Jetta offers quality•
and luxury at an affordable price. Features such as rebar, extra thick acrylic, low density insulating foam
surrounding each tub and a permanent color throughout the entire bath set Jetta apart. Each bath is
manufactured with a high gloss, high impact non-porous acrylic, which casts permanent color throughout and
is chemical, stain and UV resistant. Due to the high heat retention of this material, the acrylic is warm to the
touch, providing a more comfortable bathing experience and will maintain a beautiful appearance for years.
Unlike most bath tubs, our insulated whirlpool baths are engineered to stay hot without the use of an in-line•
heater. In fact, we are so condent in our insulation and warm air induction system, we guarantee that the
water will stay within 2 degrees of its original temperature after 30 minutes of use. The insulation surround-
ing each tub also protects the plumbing, gives added support and cuts down on noise and vibrations. The fact
that there is no hazardous heating element in contact with the bath water is also an important safety feature,
which will save you on costly wiring, operating costs, and repair bills when the heater inevitably fails.
Jetta baths are tted with full size ow-adjustable rotating and directional jets. Elite and Designer baths have •
rotating back jets that are also adjustable to stationary jets. All body jets and Classic back jets are direction
adjustable at the jet to allow focused water ow. Each full size jet is volume adjustable for a truly customized
hydro-massage.
Our air option can be added to most whirlpool baths to create the ultimate bathing experience for an•
air/whirlpool combination. The air option may also be added to most non-skirted soaker baths to provide
a gentle relaxing massage.
The passive warm air induction system is another unique feature of Jetta baths. This efcient system quietly •
recirculates heated air from the motor back to the bath water through the jets. This very efcient system
combined with the low density polyurethane foam insulation eliminates the need for an in-line heater.
Jetta whirlpools are plumbed with antimicrobial ex pipe. This antimicrobial piping is held in place by our•
insulation, uses gravity ow draining and will not hold water. Along with our 100% self draining suction
tting (IAPMO listed), this makes for a cleaner, healthier bath.
The Trissage Control offering distinct pump ow rates is standard on Designer and Elite Series and optional •
on the Classic Series. This control offers the same benet as a multi-speed pump, but eliminates the need for
expensive two and three speed pumps.
Jetta baths are extra deep - each tub is at least 20” deep, but can go to 32”, they are available in non-jetted,•
“soaker” models and several styles are also available with integral skirts with access panels.
Jetta baths are available in standard colors of White, Bone and Biscuit. A wide variety of Kohler, American•
Standard and other decorator colors are available. Each tub can be trimmed with matching acrylic or can be
upgraded to a Chrome, Polished Brass, Oil Rubbed Bronze or Satin Nickel trim kit.
Jetta baths are U.L. Listed as hydro-massage baths. Jetta baths are commercial quality and designed to reduce•
utility costs, noise complaints and service calls. Each Jetta J-Line and WaterDance Baths by Jetta bath comes
with a 10-year limited factory warranty.
Jetta baths are available with many options including contoured and jetted neck pillows, Mood or LED lights,•
waste and overow systems, aromatherapy, and 6” acrylic grab bars to customize your Jetta experience.
5
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
safety instructions
IMPORTANT: READ AND FOLLOW ALL INSTRUCTIONS PRIOR TO INSTALLATION
AND USE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Operational:
Do not permit children to use unit unless they are closely supervised at all time. Supervision is also required when1.
the bath is used by an elderly or handicapped individual.
Use this unit only for its intended use as described in this manual. Only use attachments recommended by the manufacturer.2.
Do not insert any object into any opening. Do not operate electrical appliances while in or within 5 feet of the bath.3.
Do not operate this unit without the guard over the suction tting. Long hair must be kept away from the suction 4.
screen to avoid entrapment. If entrapment occurs, immediately turn unit off.
Do not start pump before unit is lled with water 2” above jets – this will void the warranty.5.
Water level should not exceed the lowest edge of the overow or controls. 6.
The water in a whirlpool should not exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 40°C 7.
(104°F) are typically considered safe for a healthy adult. Prolonged immersions in hot water may produce hyper-
thermia. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness,
lethargy, drowsiness and fainting, which can be fatal. Lower temperatures are recommended for extended use
(exceeding 10-15 minutes) for young children.
Exposure to very hot water has the potential to cause fetal damage during the early months of pregnancy. Preg-8.
nant, or possibly pregnant women should limit water temperature to 38°C (100°F). Consult a
physician before using.
Persons using medication should consult a physician before using a whirlpool since medication may induce drowsi-9.
ness, affect heart rate, blood pressure and circulation. The use of alcohol, drugs or medication before or during
whirlpool use may lead to unconsciousness with the possibility of drowning.
Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure, circulatory10.
system problems, or diabetes should consult a physician before using a whirlpool.
Electrical:
This unit must be connected to a supply circuit that is protected by a ground-fault-circuit-interrupter (GFCI). Such 1.
a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the
test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to
operate in this manner, there is a ground current owing indicating the possibility of an electric shock. Do not use
this unit. Disconnect the unit and have the problem corrected by a qualied service representative before using.
Disconnect power before servicing.2.
Whirlpool Pump Connections Only:3.
a. A green colored terminal (or wire connector marked “G”, “GR”, “Ground” or “Grounding”) is provided within the
terminal compartment. To reduce the risk of electric shock, connect this terminal or connector to the grounding ter-
minal of your electric service or supply panel with a continuous green insulated copper wire equivalent in size to the
circuit conductors supplying this equipment.
b. A pressure ground connector is provided on the exterior of the terminal box within this unit to permit connection
of a No. 8 AWG (8.4mm²) solid copper bonding conductor between this unit and all other electrical equipment and
exposed metal in the vicinity, as needed to comply with state and local requirements.
For whirlpools and soakers the Mood or LED light option has its own separate power cord and must be plugged in.4.
Install to permit access for servicing (for built-in and custom units).5.
Installer / Owner bears all responsibility to comply with all state and local codes when installing this product.6.
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
6
owner’s manual
Verbiage Copy
installation instructions
Receiving:
Immediately upon receiving your Jetta bath, inspect it thoroughly for freight damage. If
damage is found, please note on bill of lading and contact JETTA Corporation immediately.
The surface should be protected at all times to prevent scratches.
Do not carry unit by the piping as this may cause leaks.•
Check color match before installation.•
Nothing should be placed in bath that would scratch or break it.•
Workmen in bath should be in stocking feet only.•
Testing...
Water test your unit prior to installation. Set the tub on a level surface where it can be
drained after testing. Insert drain tting and ll to the overow. Make sure all ttings,
through walls and piping are water tight. While each unit is leak tested at the factory, the
process of shipping and handling may loosen joints. If there are leaks, mark the spot(s),
drain and repair with GE Silicone Sealer (ber glass to PVC) or PVC cement (PVC to PVC).
Repeat test when dry.
Rough-In...
Test t the tub, and verify dimensions. Your Jetta bath should be installed in a bedding compound, preferably a
mortar mix or thin set, which should be distributed under the base to provide maximum support and even weight
distribution. Do not use foam, sand or drywall mud. When leveling, prepare a bed of moist mortar in the area where
bath is to be installed. Place equally spaced mounds of bedding compound, about one foot apart, 2” to 4” tall - this
should be about the diameter of a three pound coffee tin (8”-10”). When the bottom of the tub comes in contact
with the bedding compound, it should compress the mounds to a 1” to 3” layer while the tub should lightly rest on
top of the tub deck. Once the bedding compound drys, all of the weight will be carried through the oor of the tub,
not suspended by its lip. Carefully level the unit, ensuring that uniform support is given to all areas of the base
and that no portion of the lip is bearing weight. DO NOT SUPPORT THE WEIGHT OF THE BATH BY THE RIM!
Since your Jetta bath has a pre-leveled lip that accounts for the sloped oor towards the drain, the 1” x 1” drain board
attached to the bottom of the tub does not need to be removed. It is recommended that plastic is laid between the bed-
ding compound and the bath, in case removal of the bath is ever necessary.
Use union connections only for the pump. Do not overtighten. Make sure the O-rings on the pump are in place.
Hand tighten pump ttings. Do not use a wrench, channel locks, or pipe dope (teon paste).
IMPORTANT: MANUFACTURER WILL NOT BE LIABLE FOR THE REMOVAL OR RE-
INSTALLATION OF THE BATHTUB IF THERE IS A FAILURE TO FOLLOW THE MANU-
FACTURERS RECOMENDED PRE-INSTALLATION AND INSTALLATION PROCEDURES,
FAILURE TO FOLLOW THE MANUFACTURERS RECCOMENDATIONS COULD RESULT
IN THE WARRANTY BEING VOIDED.
7
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
optional skirt installation instructions
The skirt may need to be trimmed to size. Take the measurements of the skirt opening and compare1.
those of the skirt itself to determine if the skirt must be trimmed to t. If so, mark the dimensions on
the skirt and trim the skirt on the bottom and sides (do not trim the top of the skirt) and cut to within
1/8” of the required dimensions using a circular saw with sharp tooth blade. It is recommended using
a belt sander to nish trimming the sides and bottom of the skirt to the exact size of the opening.
To create a positive stop for the skirt, nail, glue or screw 2x2” or 2x4” wood blocks on both side walls2.
and along the full length of the front oor section (parallel to tub lip). The wood blocks must be mount-
ed securely against a wall or stud wall framing and the oor.
The top of the skirt is notched. Foam blocks are glued to the top backside of the skirt (section that is 3.
notched) and will compress to hold the skirt against the bathing well of the tub. Check the underside
of the tub lip for smoothness…there may be berglass chop that requires sanding so the skirt will t
snugly in place. Slide the notched top edge of the skirt under the lip of the tub. Move the bottom
section of the skirt in place until it is resting against the wood blocks. Verify the vertical edge of the
skirt is perpendicular to the oor.
Included with the skirt are two screws and decorative caps that cover /conceal the screw head and are4.
color matched to the acrylic. Drill two (2) screw holes in the bottom of the skirt – to protect the acrylic
from cracking – position to align with wood block. Screw both lower ends of the skirt through the deco-
rative caps -- through the acrylic and into the wood blocks -- to hold the skirt securely in place.
Note: the skirt is not marked where the screws should be positioned as application will dictate position.
Installer may then seal the sides and oor with caulk or silicone if so desired. 5.
Parts included for optional skirt installation:
• (1) skirt
• (2) Screws
• (2) Decorative caps
• (1) Instruction sheet
Parts / tools needed for optional skirt installation that are NOT included:
• Circular saw with sharp tooth blade and a belt sander
• Drill
• 2x2” or 2x4” wood blocks
• Caulk or silicone
• Screw driver
• Tape measure
• Square / level
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
8
owner’s manual
maintenance &cleaning
Cleaning:
Cleaning should be done with a damp cloth and a window cleaner (i.e. Glass Plus, Windex, etc.). 1. NEVER
WITH ANY SOLVENTS. Do not use an abrasive or chemical based cleanser of any kind. The ttings should
be wiped off with a damp cloth only. Bubble Bath or bath oils are not recommended for whirlpool, air or
combination baths. See dealer for specic cleaners.
If you desire additional lustre on your bath surface, you may use a good automotive wax recommended2.
for plastic surfaces. Do not wax the oor, for this may cause a slip hazard. Light scratches and abrasions
may be removed and the original gloss restored by using a light bufng compound. Use a damp cloth, rub
in small circles until scratches or abrasions are gone, then wipe with a dry cloth until the original gloss is
restored.
Repairs of any kind, if necessary, should be done by qualied acrylic experts. 3.
Proper installation and maintenance will ensure years of service and make you proud to own a bath by4.
Jetta Corporation.
It is recommended that your whirlpool, air or combination system be ushed twice per month. More frequent
service may be required depending on usage.
Flushing Procedure:
Fill your bath with hot water.1.
Add 2 tablespoons of low-foaming automatic dishwasher detergent (i.e. Cascade, Sunlight, etc.)2.
Add 1/2 cup of household bleach to the water.3.
Run the whirlpool for a minimum of fteen minutes.4.
Drain Bath5.
Rell with cold water and operate the whirlpool for fteen minutes.6.
Drain Bath.7.
NEVER operate a whirlpool bath without rst lling the tub with water to 2” above
operating jets (some models allow upper jets to be shut down for operation at a
lower water level).
Repair:
If any problems should develop, call your installer, dealer or the factory at (800) 288-7771.
9
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
operating instructions
Classic Series
The bath should be lled 2” over the directional jets BEFORE turning the pump on.
Directional Body jets:
To increase the directional jet pressure, grasp the outer ring of
the jet and turn clockwise, to reduce jet pressure turn the outer
ring
counter-clockwise.
To adjust the jet direction, use your nger to position the jet
nozzle to the desired location.
To remove jet, grasp the outer ring of the jet and turn counter
clock-wise until the jet clicks – then pull jet out.
To install a jet, insert the jet into the jet housing (do not force
the jet) and turn clockwise until the jet clicks – will pass a
point of resistance.
When bathing is complete, the pump must be turned off and the bath emptied. Adjust the inner
nozzle portion of the all the jets in a downward position while draining the bath, to allow the bath
to drain properly.
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
10
owner’s manual
operating instructions
Designer & Elite Series
The bath should be lled 2” over the jets BEFORE turning the pump on.
Rotating Back Jets:
To increase the jet pressure, grasp the outer ring of the jet
and turn clockwise; to reduce jet pressure turn the outer ring
counter-clockwise.
The upper rotating back jets can be shut-down for operation at
a lower water level. When shut down, the rotating jets will still
have a small ow of water.
To increase rotation, use your nger to position the jet nozzle
closer to the outer ring; to decrease rotation, position the jet
nozzle closer to the center of the jet.
Directional Body jets:
To increase the jet pressure, grasp the outer ring of the jet
and turn clockwise, to reduce jet pressure turn the outer ring
counter-clockwise.
To adjust the jet direction, use your nger to position the jet
nozzle to the desired location.
To remove jet, grasp the outer ring of the jet and turn counter
clock-wise until the jet clicks – then pull jet out.
To install a jet, insert the jet into the jet housing (do not force
the jet) and turn clockwise until the jet clicks – will pass a
point of resistance.
When bathing is complete, the pump must be turned off and
the bath emptied. Adjust the inner nozzle portion of the all the jets in a downward position while
draining the bath, to allow the bath to drain properly.
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Jacuzzi de Jetta
Manuales populares de Jacuzzi de otras marcas
Bestway
Bestway Lay-Z-Spa 54189 Manual de usuario
Jacuzzi
Jacuzzi ARGA ARG101C0110 Manual de lista de piezas
Morphy Richards
Morphy Richards Essentials PC4006 Manual de usuario
Softub
Softub PRESTIGE Manual de usuario
JNJ SPAS
JNJ SPAS SPA-318 Manual de instalación
KIRAMI
KIRAMI Comfort Family Manual de usuario
