JensPrima innoCon 6800D Manual de usuario
Dissolved Oxygen
mg/L
7.69
NORMAL REL 12 WASH 28.1 C
o
Online Luminescent Dissolved Oxygen Analyzer
Opera�ng Instruc�on
innoCon 6800D
WALL MOUNTING jens
innoCon 6800 Monitor Manual
Contents
Safety 2
3
5
5
6
7
8
9
9
10
11
12
13
13
14
14
14
15
16
....................................................................
..............................................................
.....................................................
....................................................
Display ..................................................................
......................................................
.........................................................
...........................................
Clean sensor ...........................................................
General ................................................................
................................................
....................................................
Analysis system ........................................................
Output ...............................................................
Interface ..............................................................
Diagnosis .............................................................
Change a fuse ..........................................................
........................................................
（RS485）......................................
Page 1
www.jensprima.com
jens
Only technicians authorized by jensprima can modify and update the instrument.
Jensprima is exempt from any damage to the instrument arising from modifica�on or
upda�ng by unauthorized personnel.
innoCon 6800 Monitor Manual
Page 2
Safety
Legal requirements
Sensor
Signs
√ This manual introduces all the risks that may arise during the use of this equipment,
√ Please make sure this manual is delivered to the third party along with innoCon 6800.
.
Please use sensors manufactured by jensprima; Damages to the instrument caused by
the use of sensors not manufactured by jensprima with in the warranty period will not be
covered by the warranty.
of corresponding regions and countries.
This sign is used to instruct the operator.
！
www.jensprima.com
jens
innoCon 6800 Monitor Manual
innoCon 6800D LDO Analyzer (Luminescent Dissolved Oxygen Analyzer) allows for easy
specially designed to meet the demands of sewage and wastewater treatment plants.
The enclosure of the controller is compliant with NEMA4X/IP65. It can display readings
sewage and
industrial wastewater treatment,fish
farming and potable water.
.
2. innoSens 450 LDO sensor x 1
1. innoCon 6800D controller x 1
Measuring principle
The innoSens 450 LDO sensor embedded with a temperature sensor carries out
sensor cap every two years. Since it does not consume any oxygen, it is applicable to any
site, including those with slow water cycling.
Features
√ Micro-computer with ARM system, highly stable and reliable
√ Dot-matrix display, with both Chinese and English versions
√ 2 groups of relays to be set at Hi/Lo output
√ Auto cleaning relay
√ 2 lines of 4-20mA current/ RS485 output
Page 3
www.jensprima.com
jens
innoCon 6800 Monitor Manual
Measurement Range (do)
Measurement Range (temp.)
Measuring principle
Accuracy
Working temperature
Working temperature
0~20.00mg/L
0~60℃
Fluorescence quenching
±0.1mg/L or ±1%
0.01mg/L，0.1℃
< 60s
-10~60℃
Working pressure
Cable
Flow rate
0~5bar
RS485 Modbus
10m
No requirement
Material
IP68
Thread 3/4” NPT
Size Φ34x197mm
Weight
Weight
850g
-10~60℃
NEMA4X/IP65
Power supply 90~260VAC，50/60Hz
Display
LCD backlit display, menu in both Chinese and English menus
Analog output 2 sets of separated 4-20mA output, adjustable, Max.600Ω
Digital output RS485 Modbus RTU
Relay
2 sets of ON/OFF relay and one set of Wash relay, Hi/Lo
alarm points can be set independently, with hysteresis
Size 160x166x75mm
1Kg
Please do not expose the
sensor to direct or
reflected sunlight.
When it is not in use, the
sensor should be shaded
from light. Any damage
the foregoing is not
covered by the warranty.
Page 4
www.jensprima.com
jens
Please mount the instrument in a place free of corrosive fluid. Chlorine will cause damage
to the sensor or affect the measurements, so the sensor must be installed at the upper
stream of the chlorine feeding point.
The enclosure of innoCon 6800 controller is specially designed to meet the requirements
Dimensions
%-""
Page 5
www.jensprima.com
jens
innoCon 6800 Monitor Manual
It is recommended that the sensor be mounted at a 45° angle, to eliminate the influence
of air bubbles on the measurement of dissolved oxygen.
Measuring Unit
Probe holder
Bracket
innoSens 450
innoCon 6800 Monitor Manual
Page 6
www.jensprima.com
jens
innoCon 6800 Monitor Manual
The connectors of the controller are located behind the instrument cover, and only
supply, relay and signal output.
Danger:
be carried out by technicians
with special training.
Notes:
Power supply must be cut off
otherwise the instrument and
the sensor are likely to be
damaged.
Terminals
Page 7
L
WASH
BK RD YE GN A B
REL2 REL1 90-260VAC
+ - 6 5 4 3 2 1 N
+ -
innoCon 6800
Temp. Measure SENSOR RS485
Power supply: 90-260VAC
L -- live wire of power supply
N-- neutral wire of power supply
RS485 output（Modbus RTU）
A-- RS485 A
B-- RS485 B
Relay output
REL1
REL2
WASH
BK
RD
YE
GN
-- Relay 1
-- Relay 2
-- Washing Relay
Analog current output
Temp.
Measure
-- Temperature current output
-- Dissolved oxygen current output
-- Black wire
-- Red wire
-- Yellow wire
-- Green wire
www.jensprima.com
jens
innoCon 6800 Monitor Manual
Display
Front view of the controller
Dissolved Oxygen
mg/L
7.69
NORMAL REL 12 WASH 28.1 C
o
o
Measurement parameter
Measurement
Status
NORMAL --
REL 1,2 -- status of Relay 1 and 2
WASH -- status of the washing relay
28.1 C -- actual temperature
Menu
Backspace
Enter
Arrows
Return to previous menu.
Accept the figure input or the menu chosen.
In measurement mode turn
on or off the backlight of the display.
In measurement mode, press and hold this
menu.
Press
Page 8
www.jensprima.com
Dissolved Oxygen
mg/L
7.69
NORMAL REL 12 WASH 28.1 C
o
jens
Tabla de contenidos
Otros manuales de Instrumento de medición de JensPrima
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario