Jensen JCR-265 Manual de usuario

MODEL JCR-265

AM/FM PROJECTION CLOCK RADIO

USER MANUAL

PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING

THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

Need technical help. Call 1800 686 079

Mon - Fri, 9 am to 5 pm

...................

WARNING:

To reduce the risk of ﬁre or electric shock, do not expose this appliance

to rain or moisture.

CAUTION:

Use of controls or adjustments or performance other than those

speciﬁed may result in hazardous radiation exposure.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions

2. Keep these instructions

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with

these instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliﬁers) that

produce heat.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The exclamation point

within an equilateral

triangle is intended to

alert the user to the

presence of important

operatingand

maintenance (servicing)

instructionsinthe

literature accompanying

the appliance.

The lightning flash with

arrowhead symbol,

within an equilateral

triangle, is intended to

alert the user to the

presence of uninsulated

"dangerous

voltage" within the

product's enclosure that

may be of sufficient

magnitude to constitute

a risk of electric shock to

persons

WARNING:

TOREDUCETHE

RISK OF ELECTRI C

SHOCK,DONOT

REMOVE COVER (OR

BACK)NO

USER-SERVICEABLE

PARTSINSIDE.

REFER SERVICING

TOQUALIFIED

SERVICE

PERSONNEL.

9. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

10. Only use attachments / accessories speciﬁed by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for

long periods of time.

12. Refer all servicing to qualiﬁed service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

13. This appliance shall not be exposed to dripping or splashing water

and that no object ﬁlled with liquids such as vases shall be placed

on the apparatus.

14. Do not overload wall outlet. Use only power source as indicated.

15. Main plug is used as disconnect device and it should remain

readily operable during intended use. In order to disconnect

the apparatus from the mains completely, the mains plug should be

disconnected form the mains socket outlet completely.

16. Do not attempt to dismantle, open or repair this product yourself. If

a fault occurs, seek advice from your local qualiﬁed service

technician or contact the distributor via the telephone number at

the back of this instruction manual.

PRECAUTION FORE USE

• UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.

• DO NOT CONNECT THE UNIT TO THE MAINS BEFORE

CHECKING THE MAINS VOLTAGE AND ALL OTHER

CONNECTIONS HAVE BEEN MADE.

• DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE

IS A SPACE OF SEVERAL CENTIMETERS AROUND THE UNIT

FOR VENTILATION.

IMPORTANT NOTES

Avoid installing the unit in locations described below:

• Places exposed to direct sunlight or close to heat radiating

appliances such as electric heaters.

• Places subject to constant vibration.

• Dusty, humid or moist places.

PROTECT YOUR FURNITURE!!

This model is equipped with non-skid rubber ‘feet’ to prevent the

product from moving when you operate the controls. These ‘feet’ are

made from non-migrating rubber material specially formulated to avoid

leaving any marks or stains on your furniture. However certain types

of oil based furniture polishes, wood preservatives, or cleaning sprays

may cause the rubber ‘feet’ to soften, and leave marks or a rubber

residue on the furniture. To prevent any damage to your furniture

we strongly recommend that you purchase small self-adhesive felt

pads, available at hardware stores and home improvement centers

everywhere, and apply these pads to the bottom of the rubber ‘feet’

before you place the product on ﬁne wooden furniture.

LOCATION OF CONTROLS

UNIT

1. MODE BUTTON

2. ALARM SET BUTTON AL. SET

3. ALARM 1 BEEPING/RADIO SELECT BUTTON AL.1

4. ALARM 2 BEEPING/RADIO SELECT BUTTON AL.2

5. ºC/ºF BUTTON

6. FOCUS ADJUSTMENT FOR PROJECTION UNIT

7. BUTTON

8. BUTTON

9. ON/OFF (ALARM OFF) BUTTON

10. SNOOZE/SLEEP BUTTON

11. LCD DISPLAY

12. DIAL SCALE AND POINTER

13. LINE IN JACK

14. VOLUME CONTROL

15. BAND SWITCH

16. TUNING CONTROL

17. RESET BUTTON

18. TEMPERATURE SENSOR(INDOOR)

19. AC POWER CORD

16 15

8910

20. FM ANTENNA WIRE

21. RATING LABEL

22. BATTERY COMPARTMENT

23. SPEAKER

24. PROJECTION ON/OFF SWITCH

25. NIGHT LIGHT ON/OFF SWITCH

PROJECTION UNIT

1. Twist the BALL counterclockwise until it loosens.

2. Pull the top half upwards.

POWER SOURCE

This unit is designed to operate on normal 240V~ 50Hz AC power only.

Do not attempt to operate the unit from any other power source. You

could cause damage to the unit.

BATTERY BACK – UP SYSTEM

This unit is also equipped with a battery back-up system for the clock

that is powered by 3 x CR2025 lithium batteries (not included).

The Battery Back-up System ensures the clock and alarm settings

will be retained during a power interruption or power outage (in order

to preserve the battery life the LCD Display will not light). All clock

settings will be kept in memory, however, the clock time may require

adjustment for exact accuracy once the power returns. If no backup

battery is installed, the Display will show “0:00” when the power is

restored. This will indicate that you have to reset the time and alarm

settings.

BATTERY INSTALLATION

1. Unscrew and pull out the Battery Compartment Door on the bottom

of the unit.

2. Follow the polarity diagram shown on the Battery Compartment

Door, insert 3 pieces of CR2025 onto the Battery Compartment

Door.

3. Replace and screw the Battery Compartment Door.

IMPORTANT: Be sure that the batteries are installed correctly.

Wrong polarity may damage the unit.

BATTERY CARE

4. If the unit is not to be used for an extended period of time, remove

the batteries. Old or leaking batteries can cause damage to the

unit and will void the warranty.

5. Do not dispose of batteries in ﬁre, batteries may leak or explode.

Remarks:

In case of malfunction due to electrostatic discharge (ESD), press the

RESET Button (#17) with the tip of a ballpoint pen or similar objects to

reset and to resume normal operation.

GETTING STARTED

Press the RESET Button (#17) on the bottom of the

unit after the unit is plugged in. The Display (#11)

will show full segments for 2 seconds then return

to current time “0:00”.

Note: Press the RESET Button (#17) with the tip

of a ballpoint pen or similar objects.

Do not use an object with a breakable or sharp tip.

SETTING THE CALENDAR AND TIME

Note: The default display and settings are 0:00 , Monday, January 1,

2007.

The clock is adjusted in the following sequence:

Current time gYear gMonth gDate gHour Format Select gHour

gMinute gCurrent time.

For example to set the calendar and date to AM 10:30, March 24,

2011.

1. In current time mode, press and hold the

MODE Button (#1) until YEAR 2007 appears

and ﬂashes in the DISPLAY (#11).

2. While the Display ﬂashes, press the Button (#8) repeatedly

until 2011 appears on the Display then press the MODE Button

(#1) once to conﬁrm the YEAR setting. The DISPLAY will show the

MONTH and DATE with the MONTH digit ﬂashing.

3. Press the or Buttons (#7 or #8) to

select the month and press the MODE Button

once to conﬁrm when the correct month (3)

appears in the DISPLAY. The DATE digit will

now ﬂash in the DISPLAY.

4. Press the or Buttons (#7 or #8) to select

the DATE and press the MODE Button (#1)

once to conﬁrm when the correct DATE (24)

appears in the DISPLAY.

The clock is now in the HOUR setting mode.

Press the or Buttons (#7 or #8) to toggle

between 24 H or 12 H display formats. Press the MODE Button

(#1) to conﬁrm the display format.

5. While the Hour digit ﬂashes, press the or Buttons (#7 or #8)

to select the hour and press the MODE Button (#1) once to enter

when the correct hour (10) appears in the DISPLAY. The MINUTE

digit will ﬂash to prompt for input.

Note: For 12 Hour format, there is a PM INDICATOR (PM) located in

the upper left-hand side of the DISPLAY. This indicator will light

when the time range falls within the “PM” range when setting

the clock. This indicator will be off when the time is in the ‘AM’

range. It is important that the “AM” or “PM” setting is correct for

proper operation of the Alarm function.

6. While the Minute digit ﬂashes, press the or Buttons (#7 or

#8) to select the minutes. Press the MODE Button once to enter

when the correct Minutes (30) appears in the DISPLAY.

The current time is then displayed.

SETTING DST- Daylight Saving Time

In current time mode, press and hold the Button (#8) for 3 seconds

to toggle the DST function on and off.

VIEWING YEAR AND DATE

In current time mode press the Button (#8) once to check the Year

or press the Button (#7) to view the Month and Date.

FOCUSING THE PROJECTION CLOCK

1. Twist the Ball counterclockwise until it loosens.

2. Pull the top of the Ball

unwards to remove it.

3. Turn the projection on by

switching the PROJECTION

Switch (#24) to the “ON”

position.

4. Focusing: Adjust the

projected clock image by turning the Focus Adjustment Knob (#6)

until the projected time is clearly shown on the ceiling or wall.

Tabla de contenidos

Otros manuales de Radio reloj de Jensen

Jensen

Jensen JCR-208 Manual de usuario

Jensen

Jensen JBS-215 Manual de usuario

Jensen

Jensen MR-720 Manual de usuario

Jensen

Jensen JCR-260 Manual de usuario

Jensen

Jensen JCR-175A Manual de usuario

Jensen

Jensen JEP-150 Manual de usuario

Jensen

Jensen QiCR-50 Manual de usuario

Jensen

Jensen JCR-225 Manual de usuario

Jensen

Jensen SAB-55A Manual de usuario

Jensen

Jensen JCR-235 Manual de usuario

Jensen

Jensen JCR-206 Manual de usuario

Jensen

Jensen JCR-255 Manual de usuario

Jensen

Jensen JCR-315 Manual de usuario

Jensen

Jensen JCR-263 Manual de usuario

Jensen

Jensen JCR-275 Manual de usuario

Jensen

Jensen JCR-255 Manual de usuario

Jensen

Jensen JBD-100 Manual de usuario

Jensen

Jensen JCR-175 Manual de usuario

Jensen

Jensen SAB-55B Manual de usuario

Jensen

Jensen Smart Talk JCR-290 Manual de usuario

Jensen

Jensen JiMS-75i Manual de usuario

Jensen

Jensen JCR-175 Manual de usuario

Jensen

Jensen JCR-295W Manual de usuario

Jensen

Jensen JCR-230 Manual de usuario

Manuales populares de Radio reloj de otras marcas

Denver

Denver CRQ-105 Manual de usuario

Audiovox

Audiovox CE90 Manual de usuario

Sony

Sony Dream Machine ICF-C763L Manual de usuario

Sanyo

Sanyo DMP-P6 Manual de usuario

RCA

RCA RPC100 Manual de usuario

Yamaha

Yamaha ISX-80 Manual de usuario

Pyle

Pyle PLMR20W Manual de usuario

Blaupunkt

Blaupunkt CR7BK Manual de usuario

Philips

Philips AJ3180 Manual de usuario

HoMedics

HoMedics SS-5500-2EU Manual de usuario

RCA

RCA RC66i Manual de usuario

Versaudio

Versaudio Vers Manual de usuario

SOUNDMASTER

SOUNDMASTER UR8100 Manual de usuario

Audiovox

Audiovox CE90 Manual de usuario

Jensen Audio

Jensen Audio JCR-222 - AM/FM Projection Alarm Clock Radio Manual de usuario

Roberts

Roberts ChronoDAB Manual de usuario

AEG

AEG MRC 4132 BT Manual de usuario

Tokai

Tokai TC-155 Manual de usuario