Jensen BT250 Manual de usuario
JENSEN BT250
B
Bl
lu
ue
et
to
oo
ot
th
h
C
Ca
ar
r
K
Ki
it
t
U
Us
se
er
r’
’s
s
M
Ma
an
nu
ua
al
l
Installation and User Manual
i
Preface
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. Neither
this manual, nor any of the material contained herein, may be reproduced
without the express written consent of the manufacturer.
Version 2.0, March 2009
Trademarks
Other product names mentioned herein are used for identification purposes
only and may be trademarks and/or registered trademarks of their respective
companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this
manual, the manufacturer and distributor assume no liability resulting from
errors or omissions in this manual, or from the use of the information contained
herein.
Bluetooth Car Kit User Manual
ii
Preface....................................................................................................................i
Installation ..............................................................................................................1
Identifying components......................................................................................1
Installing the junction box..................................................................................2
Installing the Components..................................................................................5
Installing the microphone, control, & speaker .............................................5
Introduction.............................................................................................................6
Product overview and features...........................................................................6
Pairing phones..............................................................................................8
Turning off the BT250 & the Blue LED light..............................................9
Operation with multiple paired phones ........................................................9
Resetting the Car Kit..................................................................................10
Transferring calls .......................................................................................10
Notes on using voice recognition...............................................................10
Updating the Bluetooth Software...............................................................11
Troubleshooting .........................................................................................12
Warranty Information..........................................................................................13
B
Bl
lu
ue
et
to
oo
ot
th
h
W
Wi
ir
re
el
le
es
ss
s
C
Ca
ar
r
K
Ki
it
t
Installation
This section demonstrates how to set up and install the Bluetooth
Wireless Car Kit into a vehicle.
Identifying components
Unpack the Car Kit package and ensure the following items are
included.
Wired Remote
Part # 31092000 Microphone
Part # 31092440 Junction box
Part # 31092100
Speaker
Part # 31092430
PowerCable
Part # 31092160
Fuse & Hardware Set
Part # 31092010
Some items may vary slightly from the pictureshown.
If any item is missing or damaged, contact your dealer.
Bluetooth Car Kit User Manual
2
Installing the junction box
This Car Kit is designed to work with a 12/24-volt vehicle power
supply. Refer to the following to install the junction box in a vehicle.
1. Locate a suitable place inside the car to mount the junction
box. Select a dry place that avoids excessive heat and
mechanical vibration. Ideally, the junction box should be
hidden from view, but still easily accessible.
Note: Make sure that the cables are long enough to support
the location of the junction box. If the cables are not long
enough, do not lengthen the cables; relocate the junction
box.
2. Use two screws (not included) to fasten the junction box in
place.
Connecting the power supply
The following illustration demonstrates how to connect the Car Kit’s
power cable to the vehicle’s electrical system.
Power Cable
Important!
The Blue cable must be connected to the 12/24-volt switched
ignition to enable the Car Kit to go into standby mode.
Do not connect the Blue cable to the +12/24-volt constant
connection. Doing so may discharge the battery of the vehicle and
prevent the Car Kit from being reset.
Bluetooth Car Kit User Manual
Connecting Components
The following illustration shows where to connect the devices. Do
not connect the components until you have followed the next steps
and have finalized your installation.
ÒCONNECT THE POWER HARNESS LAST.
Junction box
Speaker
Microphone Remote Control
Remote Control The control module should be located
within reach and view of the driver.
Speaker For best reception, the speaker should
be mounted at least 80 cm (30 inches)
away from the Car Kit’s microphone.
Microphone Ideally, the microphone should be
located in front of the user and above
waist height. We recommend on the
Drivers Side Window Pillar.
4
Installing the Components
Before installing the components, take note of the following:
•Make sure that the cables can reach from the each
component to the Junction Box. If the cable is too short,
relocate the component. Do not lengthen the cable.
•The supplied microphone is uni-directional. For best results,
place the microphone in front of the person talking. It has a
reception angle of 60 degrees, and is most effective within a
24 inch radius.
Installing the microphone, control, & speaker
Find a suitable place for the microphone. Remove dust and grease
from the surface.
1. Remove the protective cover
from the Velcro and press it
firmly onto the bottom of the
microphone.
2. Remove the protective cover
from the other Velcro pad, and
firmly press the pad in place.
3. Attach the microphone.
4. Repeat the same process for
the remote control.
5. Mount the speaker using two
screws in a location that is not
blocked and will allow the voice
to be heard clearly.
Bluetooth Car Kit User Manual
6
G
Ge
et
tt
ti
in
ng
g
S
St
ta
ar
rt
te
ed
d
Introduction
The Bluetooth Wireless Car Kit is designed to help make your
driving experience more convenient, safe, and provide you with
years of trouble free use.
Product overview and features
The Car Kit is designed to make driving your car and talking on the
phone safe and easy. It consists of a receiver, a remote control, a
uni-directional microphone, and a speaker. When properly installed,
the Car Kit enables you to talk freely to somebody on your mobile
phone without having to take your hands off the steering wheel.
The Car Kit is equipped with a mute feature, which turns the volume
of your car stereo down when you are using your phone. This
feature can be enabled by a trained installation professional. See
the selling dealer if you would like this feature installed.
The Bluetooth Car Kit is designed to function with many brands of
mobile phones. All featuresdepend on your phones capability to use
them. For example your phone must have Bluetooth technology to
use this car kit. Not all phones have the same features or functions.
If you have a question about your phones features refer to the
owner’s manual of your phone.
This Bluetooth Kit uses the latest Version of Bluetooth Software.
Version 2.1. In the case of an upgraded software version for new
phones in the future you can obtain the software upgrade
instructions and software at WWW.JENSEN.COM.
The BT250 is designed to be on when ever your car is turned on.
The feature allows “AUTO PAIRING” which means when you leave
the vehicle and return, as soon as you start the vehicle the BT250
will look for your phone, re-pair, and the Handsfree system will be
ready to go! You will not need to re-pair your phone each time.
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Jensen
