Jegs JEGS 30 Manual de usuario

[ 1 ]

Table of Contents

1. Transmitter Feature Diagram........................................................... 2

2. Installing Batteries ........................................................................... 3

3. Basic Operation ................................................................................. 3

4. Binding Transmitter ......................................................................... 4

5. Lock/Unlock Key Button ................................................................... 4

6. Steering Adjustment ......................................................................... 4

• Reversing Servo...................................................................................... 4

• Steering End Point Adjustment ........................................................ 5

• Steering Digital Trimming Adjustment .......................................... 5

• Dual Rate Steering Adjustment........................................................ 6

7. Throttle Adjustment .......................................................................... 6

• Throttle Reverse Setting..................................................................... 6

• Throttle End Point Adjustment......................................................... 7

• Throttle Digital Trimming Adjustment........................................... 8

8. Auxiliary Channel 3 Adjustment...................................................... 8

• Reverse Setting ...................................................................................... 8

• On/Off CH3 Switch Setting................................................................ 9

9. Factory Reset ..................................................................................... 9

• Factory Default Setting ....................................................................... 9

10. FUNC................................................................................................. 9

• FUNC Mode

11. Receiver..........................................................................................10

• Receiver Binding ..................................................................................10

• Fail-Safe Adjustment..........................................................................10

12. Power Alarm ..................................................................................10

• No Activity Alarm.................................................................................10

• Low Battery Voltage Alarm...............................................................10

13. Certication ...................................................................................11

14. Specications ................................................................................12

[ 2 ]

1 — Transmitter Feature Diagram

[ 3 ]

2 — Installing Batteries

1. Remove the battery cover from the transmitter.

2. Insert 4 AA alkaline dry cell batteries

according to their polarity.

3. Replace the battery cover.

3 — Basic Operation

[ 4 ]

4 — Binding Transmitter

1. Each transmitter is assigned a random unique ID number. In order to

begin using the transmitter system, you will have to bind the receiver

to the transmitter.

2. Follow the receiver binding instructions on page 10.

5 — Lock/Unlock Key Button

6 — Steering Adjustment

Lock Key Button

1. Push the D/R switch to the Right.

2. While holding the D/R switch

to the right, turn the transmitter

power switch to ON.

3. Two short “beep” sounds indicate

conrmation and the LED light

ashes.

4. All button functions are

now locked.

Unlock Key button

1. Push the D/R switch to the Left.

2. While holding the D/R to the left,

turn the transmitter power switch

ON.

3. Two short “beep” sounds indicate

conrmation.

4. All button functions are

now unlocked.

Reversing Servo

1. Press and hold steering wheel

(ST) R/+ key button.

2. While pressing ST R/+ key

button, turn on the transmitter

power switch.

3. Two short “beep” sounds

indicate conrmation.

4. The steering has now

been reversed.

[ ST = Steering Wheel TH = Throttle Trigger ]

[ 5 ]

Left Steering End Point Adjustment

1. Turn the steering wheel (ST) fully to the left.

2. Once the value reaches the limit,

a long steady “beep” will sound.

• Decrease value: Turn the steering

wheel fully to left and press

ST L-key button

• Increase value: Turn the steering

wheel fully to the left and press

ST R+ key button

3. Use this to decrease or increase left steering angle adjustment.

Steering Digital Trimming Adjustment

1. Once the value reaches the limit,

a long steady “beep” will sound.

2. Two short “beep” sounds indicate the

steering is at the neutral position.

a. Decrease: Press ST L/- key button

b. Increase: Press ST R/+ key button

3. When the vehicle is not moving, this

function allows you to adjust the

steering to the neutral position.

Right Steering End Point Adjustment

1. Turn the steering wheel (ST) fully to the right

2. Once the value reaches the limit,

a long steady “beep” will sound.

• Decrease value: Turn the steering

wheel fully to the right then press

ST L- key button

• Increase value: Turn the steering

wheel fully to the right then press

ST R+ key button

3. Use this to decrease or increase right steering angle adjustment.

Steering End Point Adjustment

[ ST = Steering Wheel TH = Throttle Trigger ]

[ 6 ]

Dual Rate Steering Adjustment

• Decrease: Push the D/R button

to the left

• Increase: Push the D/R button

to the right

1. Once the value reaches the limit,

a long steady "beep" will sound.

2. Dual-rate Steering allows on-the

y travel adjustment to both sides

(left and right) of the steering servo.

7 — Throttle Adjustment

Throttle Reverse Setting

1. Press and hold ST L/- key button.

2. While holding ST L/- key button turn the transmitter power switch to ON.

3. Two short “beep” sounds indicate conrmation.

4. The throttle trigger has now been reversed.

[ ST = Steering Wheel TH = Throttle Trigger ]

[ 7 ]

Throttle (Accelerate)

1. Pull and hold the throttle trigger

(TH) fully to the Forward-side.

2. Once the value reaches the limit,

a long steady “beep” will sound.

• Decrease: While holding the

throttle trigger, press

TH Rev/- button

• Increase: While holding the

throttle trigger, press

TH Fwd/+ button

3. Use the TH Rev/- or TH Fwd/+

buttons to adjust the throttle

trigger to desired throw.

4. This can also be performed when the

receiver power is off.

Throttle End Point Adjustment

Brake (Decelerate)

1. Push the throttle trigger (TH) fully

to the brake-side

2. Once the value reaches the limit,

a long steady “beep” will sound.

• Decrease: While holding the brake

trigger, press TH Rev/- button

• Increase: While holding the brake

trigger, press TH Fwd/+ button

3. Use the TH Rev/- or TH Fwd/+

buttons to adjust the brake to

desired throw.

4. This can also be performed when

the receiver power is off.

[ ST = Steering Wheel TH = Throttle Trigger ]

[ 8 ]

When the vehicle is not moving, this

function allows you to adjust the

throttle to the neutral position.

1. Once the value reaches the limit,

a long steady “beep” will sound.

2. Two short “beep” sounds indicate

conrmation.

• Decrease: Press TH Rev/-

button

• Increase: Press TH Fwd/+

button

3. If the value is lower than the

setting limit of ESC, some

functions may be invalid.

8. Auxiliary Channel 3 Adjustment

Reverse Setting

1. Press and hold CH3 key button

while turning the power switch on.

2. Listen for Two short “beep” sounds

for conrmation.

3. The CH3 Function has now been

reversed.

Throttle Digital Trimming Adjustment

[ ST = Steering Wheel TH = Throttle Trigger ]

[ 9 ]

On/Off CH3 Switch Setting

This function allow you to turn On/Off the

CH3 key-button.

1. Two quick presses of the CH3 key button.

• Turn-On: Two short beep sounds

• Turn-Off: One short beep sound

9 — Factory Reset

Factory Default Setting

1. Press and hold the TH Fwd/+ or TH Rev/- key button.

2. While holding the Fwd/+ or Rev/- key button turn

the transmitter switch to ON.

3. Two short beep for conrmation.

4. Your transmitter has now

reset to the factory

setting.

10 — FUNC

FUNC Mode

FUNC Mode locks all the key buttons and

throttle except the steering wheel.

1. To enter the FUNC mode, Turn the

transmitter power switch to ON, press

and hold the FUNC key button, two short

“beep” sounds for conrmation.

2. To leave the FUNC mode, press the FUNC

key button once, two short “beeps” will

sound for conrmation.

[ ST = Steering Wheel TH = Throttle Trigger ]

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario