JCROffroad XJRC Guía de configuración

Thank you for purchasing from JcrOroad! Checkout our website, www.jcroroad.com for other great o-road

products. Be sure to rate and review our product online. If you have any questions or are missing parts, please

don’t hesitate to call us at 269-353-1184!

Please read the mounting instructions below carefully before attempting to install.

Be sure to check out the install video on the product page, if available.

JEEP CHEROKEE XJ (84-01)

REAR CRUSADER BUMPER

INSTALL INSTRUCTIONS

6x 12x

1/2”-13

Locknut

1/2”

USS Washer

1/2-13 1-1/2”

Hex Head

6x

INCLUDED HARDWARE

INCLUDED PARTS

1x

1L/1R

1L/1R

Start by removing the factory rear bumper. There are two mounting brackets from the

bumper to the back of the bulkhead with 4 bolts each. (Photo shown is with the bumper

skin removed for illustration purposes.)

If you’re installing on a 97’ and up, and are not installing our lower quarter panel armor,

you have the option of cutting the plastic side skirts on the lower quarter panels (as

shown below) and leaving much of it behind. Draw a straight line down from where the

tail lights attach to the body and trim the factory plastic with a utility knife.

1.

2.

INSTALLATION

If our nutstrips were purchased, remove whatever factory nut strips were inside the

frame rails ﬁrst. (If installed) You will need to unbolt any hitches, skids, or exhaust mounts

that are bolted under the frame.

Insert the new nutstrips into frame. You may want to loosely install one bolt on the

forward most hole to help keep them aligned. For more inststruction, please look at the

XJ Rear Nutstrip Install Instructions.

If not using nutstrips, the uniframe tie-in brackets will need to be loosely installed before

the bumper. (See step 11) By utilizing the lock washer inside the frame, the tie-ins will

later be able to be tightened down without needing a wrench on the nut. Just remember

to keep them somewhat moveable for alignment purposes at this time.

3.

4.

5.

INSTALLATION

Li the bumper into place over the frame side mounts. Use a helper or a jack to hold it

into position and make sure it is somewhat level.

7.

INSTALLATION

Install frame side bumper brackets with the slotted holes facing out and the oset down.

Reusing factory bolts, center brackets with slots/holes. The outside width should be

roughly 39 3/4".

6.

Adjust bumper pitch and height with the 5/8" bolts, or le and right with the frame side

bolts/slots. Check the operation of the tailgate, lower the bumper down if the gate hits

the top of the bumper.

Using the included 5/8" bolts, washers and nuts, reach up behind bumper and install into

slots from the outside in. Assemble in the orientation shown below, and be sure to do

this on both sides of the bumper. The swept back design of the bumper prohibits working

a lot room on this step, so exhibit patience! *Alternatively, you can bolt the frame side

brackets onto the bumper before hoisting the whole assembly onto the frame. You can

pull the weather stripping out of the way to gain access to the upper bolts on the frame

side mounts. This method may take a time or two to get the alignment of everything

correct.

9.

8.

INSTALLATION

If you chose to purchase our integrated lower quarter panels, install them at this time

using the XJ Integrated Lower quarter panel instructions found on the product oage

on our website. The only dierence being, you will need to drill the holes where they set

over the bumpers to install that hardware. Be sure to do this aer the bumpers has been

correctly aligned.

12.

INSTALLATION

Once you are happy with the look and alignment, tighten down all of the hardware. If you

have access, a one or two foot extension can be used to more easily reach the 5/8" nuts.

If your using nutstrips, install any additional skids and the unibody tie in’s at this point.

Their orientation (welded on spacer on top or bottom) will depend on what options

you have on your Jeep. With no skids or receivers the spacer will be on top. With any

additional bracketry under the frame, you may need to ﬂip the brackets side to side and

leave the welded spacer underneath.

10.

11.

INSTALLATION

Once all of your hardware is tight, your bumper install is now complete. Enjoy your new

rear bumper!

13.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de JCROffroad

JCROffroad

JCROffroad XJRK Manual de usuario

JCROffroad

JCROffroad JKSD-FL Manual de usuario

JCROffroad

JCROffroad 6TH GEN BRONCO Manual de usuario

JCROffroad

JCROffroad JT Guía de configuración

JCROffroad

JCROffroad UNI-FPF-PC Guía de configuración

JCROffroad

JCROffroad JT Guía de configuración

JCROffroad

JCROffroad BR6RMP Guía de configuración

JCROffroad

JCROffroad JTRWP Manual de usuario

JCROffroad

JCROffroad VRK-SAM Manual de usuario

JCROffroad

JCROffroad 6TH GEN BRONCO Guía de configuración

JCROffroad

JCROffroad LPRLC2 Guía de configuración

JCROffroad

JCROffroad JK WRANGLER Guía de configuración

JCROffroad

JCROffroad DIY-XJ-F-WN Manual de usuario

JCROffroad

JCROffroad MOLLE Guía de configuración

JCROffroad

JCROffroad JEEP GL ADIATOR JT TOPPER ROOF RACK Guía de configuración

JCROffroad

JCROffroad BR6-UPRS Guía de configuración

JCROffroad

JCROffroad OGFL-BR6G Manual de usuario

JCROffroad

JCROffroad XJ Guía de configuración

JCROffroad

JCROffroad BR6TD Guía de configuración

JCROffroad

JCROffroad REAR MOLLE PANEL Guía de configuración

JCROffroad

JCROffroad JLRK Manual de usuario

JCROffroad

JCROffroad 6TH GEN BRONCO Guía de configuración

JCROffroad

JCROffroad JT OVERLAND BED RACK Guía de configuración

JCROffroad

JCROffroad XJCB-PC Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario