JCM TSP-01 Manual de usuario
2002 JCM – American, Corp.
Office: (800) 683-7248 Technical Support: (702) 651-3444 FAX: (702) 651-0214
Thermal Printer Series - 100
JCM part No. 960-000038
Table of Contents
Introduction.............................................................................................................................. 1
Model Classification ................................................................................................................ 2
General Specifications ............................................................................................................. 3
Dip Switch Settings ................................................................................................................. 5
Thermal Paper Specifications .................................................................................................. 6
Photo of Printer ........................................................................................................................ 9
Pin Outs ................................................................................................................................. 10
Installation ............................................................................................................................. 11
Typical Mounting Holes ........................................................................................................ 11
Operation ............................................................................................................................... 12
Calibration ............................................................................................................................. 12
Troubleshooting ..................................................................................................................... 14
Cleaning ................................................................................................................................. 17
System Logic Diagram .......................................................................................................... 18
Illustrated Parts Breakdown ................................................................................................... 20
Parts List ................................................................................................................................ 21
JCM and the JCM logo are registered trademarks of Japan Cash Machine Co., Ltd. and JCM American Corpo-
ration. All other marks in this publication are registered trademarks of their respective owners.
Introduction
The Thermal Security Printer – TSP-01
The TSP-01 is a multi-purpose printer that is
suitable for any application requiring quality
printing ability.
JCM provides the thermal paper specifica-
tions for optimum performance (see page X),
while allowing the customer the freedom to
create a unique 4-color design on the top
surface. The thermal side is reserved for the
barcode created by the thermal printer, which
is read by bill acceptors and other barcode
reading devices. The TSP-01 uses pre-cut,
pre-printed paper that offers the following
advantages:
• No curled paper or tickets from the end of
a roll that could cause a jam when in-
serted into a bill validator.
• No wasted paper such as found when
using roll or fanfold thermal paper.
• No cutting device necessary within the
printer that can cause failures or malfunc-
tions during operations.
• No complex paper loading procedures
such as found with rolled or fanfold
paper.
• Customers can reload the pre-cut paper at
any time to the maximum quantity.
Read-After-Write (RAW)
JCM’s RAW feature verifies the accuracy and
quality of the printed ticket prior to dispens-
ing it. If the printer senses a problem, it
stores the ticket internally, and sends an error
message to the host machine. The printer
then attempts to reprint the ticket.
1
Model Classification
How to read the Model Classification Number
CATEGORY 813 TSP PRINTER
TSP – X X – X X – X XX – X X –XXX
(1) (2) (3) (4)(5)(6) (7) (8)
(1) TSP Thermal Security Printer
(2) CPU
01 4 MB EPROM w/barcode verify
(3) Mounting & Cable Bracket configuration
00 No mounting brackets, no cabling.
01 No mounting brackets, 024 cable output
02 Front hook bracket, long rear bracket; 024 cable output
03 Flat front bracket, short rear bracket; 024 cable output
04 No mounting brackets; ribbon cable output
05 No front bracket, small rear bracket; ribbon cable output
06 No front bracket; small rear bracket; ribbon cable w/header
(4) Paper capacity
3 250 notes
5 500 notes
(5) Paper size
1 65 mm x 156 mm (US $)
(6) Faceplate
0 No Faceplate
(7) Type of Software
03 ID-003 JCM Standard
24 ID-024 IGT Netplex
(8) Other Options
001 – Standard configuration
Examples:
TSP-01-05-310-03-001
Printer model 01 with no front bracket, small rear style mounting, 003 ribbon style cable; 250 note
capacity;
USA size paper; no faceplate; ID-003 software, no special options.
2
General Specifications
Outside Dimensions
Width : 113 mm (4.448 inches)
Height : 67.5 mm (2.657 inches)
Depth : 279.4 mm (11 inches)
Weight
1.5 Kg, or 3.3 lbs
Power Requirements
DC 24V (+10%, -5%)
3A (50% print ratio)
Paper Hopper Capacity
250 standard.
Optional hopper extensions
for 500 pre-cut pieces available
Recommended Thermal Paper
Part No. KF50 - HDA or compatible
NOTE: Using other paper may affect the
quality and thermal printer head longevity.
Contact your JCM account repesentative
for a list of qualified suppliers.
Paper Dimensions
66 mm Width
156 mm Length
3
General Specifications: Cont’d
Paper Rejection Function - .
R.A.W - Read After Write
When sensors detect double paper, or a barcode print failure condition, the paper is sent to an
internal reject area and an error code is sent to the host application.
The reject area has a capacity of 5 sheets.
Installation
Indoors
No Sunlight
A lengthwise installation angle between 0O and 45O degrees
Operating Environment
Temperature : +5O C ~ +45O C
Humidity : 10 ~ 90% RH (no condensation)
Storage Environment
Temperature : -25O C ~ +70O C
Humidity : 10 ~ 90% RH (no condensation)
Types of Sensor Detectors
Paper Out Sensor
Paper Near Out Sensor
Paper Dispensed Sensor
Paper Reject Sensor
Double Paper Sensor
Barcode Read Sensor
Printing Method Dot Density Effective Print Dot Area
Thermal line dot method 8 dots / mm 480 dots wide
1200 dots long
Effective Print Area Maximum Print Speed Thermal Print Head Rating
60 mm X 150 mm 75 mm / second Pulse Life : 50 million pulses
Abrasion Life : 50 km
Handling Time
From receipt of data to full dispense : ~ 5 seconds
Paper pick up time (from box to head) : ~ 1 second
Print time : ~ 2 seconds
Dispense time (from print finish to full dispense) : ~ 2 seconds
4
Dip Switch Settings
Dip Switches
OFF
4 3 2 1
OFF
4 3 2 1
OFF
4 3 2 1
OFF
4 3 2 1
OFF
4 3 2 1
Normal Operating Setting - This is the default setting for
normal communication via the host application.
Dip Switch #1: Off = Barcode check
On = No barcode check
Others are default to OFF position
Coupon Print Test - Will print a ticket and check the barcode. If
there is something wrong with the barcode, VOID will be printed
on the ticket and it will be transported to the reject area.
Print Bar Sensor Signal and Data - A barcode ticket is printed.
The sensor signal and data are printed on the following piece of
paper. This is used to make sure barcode and transparency sen-
sors are adjusted properly.
Print Test pattern and Version Information - Print a test
pattern, model name and version number. This feature is useful
for quickly checking print quality.
Adjust Barcode and Transparency Sensors - To be used when
attempting to use the Sensor Adjustment procedure.
NOTE: Dip switches must be set with the power OFF. W#hen power is turned ON, the operation begins.
5
Thermal Paper Specifications
1. Overview
This specification is for thermally coated tickets designed for use with the JCM
TSP-01 thermal printer.
2. General Characteristics
2.1 Tickets to be pre-cut sheets.
2.2 Ticket edges must be smooth to prevent double feeding.
2.3 Ticket size: 65 ± 1 mm x 156 ± 1 mm.
2.4 Tickets to be supplied in bulk stacks of 200.
2.5 Each stack shall have a tear off band.
2.6 Tickets must be processed and cut in a manner that minimizes paper dust.
3. Thermal Paper Specification
ITEM SPEC.
Weight g/m² 102 Avg
Caliper µ 114 Avg (4.5 mils)
Brightness % 89 Avg
Smoothness sec. 2000 Avg
Image Colors Black
Initial Activation Temp. ° C 74 ± 5 O.D. = 0.2
Effective Activation Temp. ° C 83 ± 5 O.D. = 0.8
Optimum Activation Temp. ° C 90 ± 5 O.D. = 1.2
Resistance of Oils Very Good
Resistance of Alcohol, Solvents Very Good
15 Hr. Water Immersion Very Good
6
4. Paper Curl
The deformation (curl and warp) of papers used for TSP-01 printers is limited as follows.
Deformation to be measured after paper has been stabilized for a minimum of 48 hours
at 20 ± 5o C, 55 ± 15% RH.
5. Thermal side printing
5.1 Ticket shall have the text: “INSERT THIS SIDE UP” preprinted in heat resistant
black ink along the 65 mm edge as show in Figure 1. Font size shall be 12 pt.
5.2 Lot code, date code or other information identifying the printing date or batch number
shall be printed in heat resistant black ink along one of the 65 mm edges as shown in
Figure 1. An arrow or other symbol indicating paper grain orientation shall also be
included. Font size shall be 4 pt.
5.3 No other preprinting is allowed on the thermal side without prior approval of JCM
American Corp.
6. Non-thermal side printing
6.1 The non-thermal side may be preprinted with multi colored graphic images. All
printing on the non-thermal side must be within the area shown in Figure 2.
POSITIVE WARP
ZERO ALLOWED
THERMAL SIDE UP
NEGATIVE WARP
5MM TOTAL MAX.
5MM PER 156MM IS
.032INCHES/INCH
POSITIVE CURL
ZERO ALLOWED
THERMAL SIDE UP
NEGATIVE CURL
5MM TOTAL MAX.
5MM PER 67MM IS
.075INCHES/INCH
7
6.2 It is recommended that non-thermal side printing be pre-approved by JCM American
Corp. prior to use to ensure no negative impacts on print or printer reliability.
7. Packaging
7.1 Paper shall be packaged in cartons or boxes designed to protect tickets from damage.
7.2 Packaging must shield tickets from ambient light.
7.3 Package to have “THIS SIDE UP” or similar marking in large bold print to ensure
that tickets are shipped and stored horizontally to minimize warp and curl.
7.4 Package to have suggested storage temperature and humidity conditions printed on
carton. (Example: Store at 70oF and 50% RH)
8
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
