JBL BPx1100.1 Manual de usuario
BPX1100.1
2 CHANNEL
POWER AMPLIFIER
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797 Rev1 2/2004
CONTENTS
Specifications………………………….…………………..……1
Features…………………………………………………………2
Test Conditions And Notes……………………………………2
Controls/connections…………………………………..………3
Mounting…………………………………………….…..………3
Applications………………………………………..……………4
Typical System Configuration…………………………………5
Troubleshooting……………………………………….……..…6
PCB drawings……………………………………..……………7
Electrical Parts List……………………………………………10
Mechanical Parts List……………….………………..………13
Block Diagrams……………………………………….………14
Semiconductor Pinouts………………………………………15
Exploded view…………………………………………………20
Schematics……………………………………………….……21
Packing………………………………….………………………30
SPECIFICATIONS
Power Output, 4 Ohms: n/a
Power Output, 2 Ohms: 575W x 2
Power Output, Bridged, 4 Ohms: 1100W x 1
Power Output, Parallel, 1 Ohm: 1100W x 1
MIN. Speaker Impedance: 1 ohm
Frequency Response: 20Hz~320Hz, -3dB
Input Sensitivity (RCA type): 250mV~6V
THD + Noise (4 Ohms): 0.5%
Signal-to-Noise: 93 dB
Maximum Current Draw: 110A
Fuse Replacement: 30Ax3
External Dimensions:
Length 12 ¼” (312mm)
Width 17” (432mm)
Depth 2 9/16” (66mm)
JBL continually strives to improve its products. New materials, production methods and design refinements are introduced into existing
models without notice as a routine expression of our design philosophy. For this reason, Power Series Multichannel Automotive
Amplifiers may differ in some respects from their published specifications and descriptions, but will always equal or exceed the original
specifications unless otherwise stated.
Power Amplifier
BPX1100.1
Test Conditions and Notes
2-Channel Operation
Advanced MOSFET Oversized Floating Rail Power Supply
Floating Ground Factory - Head - Unit Speaker - Level input
Variable Input Sensitivity (250mV - 6V)
Fully Complementary Output Stage with Class-D Voltage Amplification
Gold-plated Power, Input and Output Connectors
1-Ohm Stable ( 2 ohm parallel )
All tests to be done, unless otherwise specified, from 20Hz to 320Hz at 14.4V DC into 2 ohm loads and adjust
the units gain so that with a .775 volt input signal the unit is at its maximum rated output. All measurements
will be done using an Audio precision system one and the supply voltage.
An A+ line voltage of 14.4V DC shall be applied to the unit under test for all measurements unless otherwise
specified. The voltage applied to the unit shall be measured at the power connection on the Amplifier.
Signal Source
Unless otherwise specified, all tests shall be conducted with the Audio Signal Generator output configured to
be balanced, less than or equal to 50 ohm source impedance, and floating. The signal source "GND" shall be
connected to the Amplifier PWR GND at the Amplifier.
Output Load
Unless otherwise specified, all tests shall be conducted with 2 ohm resistive loads having less than 10%
reactive components at any frequency below 350Hz. Each resistor shall have a value that remains within 1%
while dissipating the rated output of the unit under test.
Power Indicator LED steadily illuminates for normal operation. LED blinks when
protection circuitry is engaged, and during power up.
Features
BPX1100.1
Power Amplifier
2
Controls and Connections
Mounting the Amplifier
The JBL BP Series amplifiers can be mounted in virtually any location inside the vehicle.
However, make sure to keep the amplifier away from heater vents or ducts.
1. At the chosen site, use the amplifier as a mounting template and mark the locations of the
four mounting holes.
2. Drill a small pilot hole at each marked location.
3. Mount the amplifier and securely tighten the mounting screws.
BPX1100.1
Power Amplifier
Controls and Connections
4. Preamp-Level Input Connector - Connects to
5. Pre amp-Level AUX output Connector
line-level output from the source unit.
3. Speaker Output Connector - Connect speaker
wiring to these connectors. See wiring instruc-
tions on page 4 for more information.
2. Fuse - Three 30 Amp ATC type Fuses.
1. Power Connection for 12V+, GND and REM
connections for power wires. See wiring instruc-
tions on page 4 for more information.
6. Input-Level Control - Adjusts input sensitivity
7. This switch is select X-over slope
for pre-amp level and speaker level inputs.
10. The crossover frequency can be set at any frequency
11. (1) The HP frequency can be set at any frequency
(2) Bass Boost control will provide at frequency
Between 32Hz and 320Hz.
Between 20Hz and 100Hz.
Being set between 20Hz ~ 100Hz
9.
8. This switch is set to 2-channel mode(2CH/BR) to drive
a pair of subwoofers or bridge(mono) mode to drive a
single subwoofer(PARALLEL).
It's allowed to use parallel mode when the nominal
impedance of the speaker system is 2 ohm or greater
1 2 3
4 56
8
97
1011
Remotr Volume Control Jack.
3
APPLICATIONS – BPx MODELS
To the right are several application
diagrams to help plan your subwoofer
system installation. Figures 1 through 3
show how to configure the JBL Power
Series subwoofer amplifiers (models
BPx500.1, BPx1100.1 and BPx2200.1)
for 2-channel, bridged-mono and
parallel-mono operation
“Setting the Output Mode” on page 6).
NOTE: For simplicity, Figures 1 through
3 do not show power, remote and input
connections.
NOTE: If the nominal impedance
of your speaker system is close to
2 ohms, be prepared to try both
bridged and parallel configurations to
determine which performs better.
3
BPx Amplifier
(partial rear panel)
*
SEE MANUAL FOR PARALLEL CONNECTION
2 CHANNEL
BRIDGED
PARALLEL
*
CH 1
CH 2
SPEAKER OUTPUTS
NEON
Subwoofer Subwoofer
Set OUTPUT MODE
to 2CH/BR
(on input panel)
PARALLEL 2CH/BR
OUTPUT MODE
12dB 24dB
32Hz 320Hz
FREQ
SLOPE
X-OVER
BPx Amplifier
(partial rear panel)
*
SEE MANUAL FOR PARALLEL CONNECTION
2 CHANNEL
BRIDGED
PARALLEL
*
CH 1
CH 2
SPEAKER OUTPUTS
NEON
Subwoofer (less than 2 ohms)
Set OUTPUT MODE
to PARALLEL
(on input panel)
PARALLEL 2CH/BR
OUTPUT MODE
12dB 24dB
32Hz 320Hz
FREQ
SLOPE
X-OVER
jumper
Figure 1. The JBL Power Series
subwoofer amplifier is set to
2-channel mode to drive a pair
of subwoofers.
Figure 2. The JBL Power Series
subwoofer amplifier is set to
bridged (mono) mode to drive
a single subwoofer. Use this
mode only when the nominal
impedance of the speaker
system is 2 ohms or greater.
Figure 3. The JBL Power Series
subwoofer amplifier is set to
parallel mode to drive a single
subwoofer. Use this mode only
when the nominal impedance
of the speaker system is less
than 2 ohms.
NOTE: A jumper is added
between the + terminals.
BPx Amplifier
(partial rear panel)
*
SEE MANUAL FOR PARALLEL CONNECTION
2 CHANNEL
BRIDGED
PARALLEL
*
CH 1
CH 2
SPEAKER OUTPUTS
NEON
Subwoofer (2 ohms or greater)
Set OUTPUT MODE
to 2CH/BR
(on input panel)
PARALLEL 2CH/BR
OUTPUT MODE
12dB 24dB
32Hz 320Hz
FREQ
SLOPE
X-OVER
Power Series Amp OM 5/20/03 10:51 AM Page 3
Power Amplifier
BPX1100.1
Typical System Configuration
Vehicle Battery
Chassis Ground
Ignition
Switch
CD Player or Changer
Cassette/CD Tuner
(Head Unit)
Power Ground
Speakers
60 Amp (Not Included) Main +12V
Amplifier
Power
Connection
Line
Level
Input
Remote On/Off
Remote Antenna
Power Supply
Antenna Motor Ground
Remote On/Off
Black - Power Ground
Red - Main +12V
Black Power
Antenna Input
Power
Antenna
Cassette/Receiver
Power Supply
Wires
Fuse
Fuse
Fuse
Power
Antenna
Relay
BPX1100.1
Power Amplifier
4
TROUBLESHOOTING
SYMPTOM LIKELY CAUSE SOLUTION
No audio No voltage at BATT+ Check voltages at
(POWER LED or REM terminals, amplifier terminals
is off) or bad or no ground with VOM
connection
No audio DC voltage on Amplifier may need
(PROTECT LED amplifier output service; see enclosed
flashes every warranty card for
4 sec.) service information
No audio Amplifier is Make sure amplifier
(PROTECT overheated cooling is not blocked
LED is on) at mounting location;
verify speaker-system
impedance is within
specified limits (see
“Specifications” on the
next page)
No audio Voltage less than 9V on Check vehicle
(PROTECT BATT+ connection charging system for
and POWER defective voltage
LEDs flash) regulator
I-E/OPT LED Amplifier is being Check INPUT
is on all times overdriven LEVEL setting;
(not flashing) see previous page
No audio Voltage more than 16V Check vehicle
(PROTECT or less than 8.5V on charging system for
LED is on) BATT+ connection defective voltage
regulator
Distorted audio Input sensitivity is Check INPUT
not set properly, or LEVEL setting; or
amplifier or source check speaker wires
unit is defective for shorts or grounds
Distorted audio Short circuit in Remove speaker leads
and PROTECT speaker or wire one at a time to locate
LED flashes shorted speaker or
wire, then repair
Music lacks Speakers are not Check speaker
“punch” connected properly connections for
proper polarity
Power Amplifier
BPX1100.1
Printed Circuit Board (Top View)
BPX1100.1
Power Amplifier
5
Printed Circuit Board (BOTTOM View)
BPX1100.1
Power Amplifier
6
Printed Circuit Board (SUB TOP View)
BPX1100.1
Power Amplifier
PAS132-01
PAS132-01
PAS132-01
PAS132-01
PAS132-01
PAS132-01
PAS132-01
PAS132-01
PAS132-01
PAS132-01
REV.0
REV.0
REV.0
REV.0
REV.0
REV.0
REV.0
REV.0
REV.0
REV.0
A20K
2K
623PCB4-B
A20K
2K
623PCB4-B
A20K
2K
623PCB4-B
A20K
2K
623PCB4-B 623PCB4-B
2K
A20K
A20K
2K
623PCB4-B
A20K
2K
623PCB4-B 623PCB4-B
2K
A20K A20K
2K
623PCB4-B 623PCB4-B
2K
A20K
VR701
R701
MOD02
VR701
R701
MOD02
VR701
R701
MOD02
VR701
R701
MOD02 MOD02
R701
VR701
VR701
R701
MOD02
VR701
R701
MOD02 MOD02
R701
VR701
VR701
R701
MOD02 MOD02
R701
VR701
7
Otros manuales para BPx1100.1
2
Tabla de contenidos
Otros manuales de Amplificador de JBL
JBL
JBL Club A600 Manual de usuario
JBL
JBL VMA160 Manual de usuario
JBL
JBL PX600.2 Manual de usuario
JBL
JBL Synthesis SDA-1700 Manual de usuario
JBL
JBL BP600.1 Manual de usuario
JBL
JBL BP1200.1 Manual de usuario
JBL
JBL GX-A604 Manual de instalación y operación
JBL
JBL Synthesis S5160 Manual de usuario
JBL
JBL GT-X646 Manual de usuario
JBL
JBL Synthesis S800 Manual de usuario
JBL
JBL 6290 Manual de usuario
JBL
JBL GTR-7535/104/102 Manual de usuario
JBL
JBL SR Series Manual de usuario
JBL
JBL 5306 Manual de usuario
JBL
JBL GTO-3EZ Manual de usuario
JBL
JBL SR6670A Manual de usuario
JBL
JBL GTR-7535 Manual de usuario
JBL
JBL DA850 Manual de usuario
JBL
JBL GTO5355 Manual de usuario
JBL
JBL GT5-S422 Manual de usuario
