Jbc GAL0405 Manual de usuario

Este manual sirve para los siguientes modelos

9

Tabla de contenidos

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar

Goobay

Goobay 97790 Manual de usuario

GAL0405, GAL0608,

GAL0910, GAL1115, GAL1618

Guide Kits for AL250

INSTRUCTION MANUAL

Guide kit for AL250 .................................. 1 unit

Packing List

The following items should be included:

Manual ......................................................... 1 unit

Ref. 0033061

*Driver gear is included only in the Ø 1.1 - 1.5

mm & Ø 1.6 - 1.8 mm guide sets for a correct

dragging of the solder wire.

Ref. 0002399 - Ø 0.4 - 0.5 mm / 0.015 - 0.02 in

Ref. 0002402 - Ø 0.6 - 0.8 mm / 0.023 - 0.03 in

Ref. 0002401 - Ø 0.9 - 1.0 mm / 0.035 - 0.04 in

Ref. 0002843 - Ø 1.1 - 1.5 mm / 0.043 - 0.06 in

Ref. 0013915 - Ø 1.6 - 1.8 mm / 0.062 - 0.07 in

This manual corresponds to the following references:

driver gear

2

1. Unlock the dragging mechanism.

Guide Set

1

2

2

Guide Set Assembly

8-10 m m

(0.31 - 0.40 in)

Guide tube screw

3

4

3. Insert the guide set in the tool. You

must leave a gap of 8-10 mm between the

cartridge tip and the end of the guide tube.

4. Tighten the guide tube screw to block the

position of the guide.

2. Place the guide set and tighten the

screws.

www.jbctools.com

3

6

5. Draw the solder wire from the reel to the

entrance of the guide tube.

Guide

tube entrance

5

6. Close the dragging mechanism.

4

LOADING

SOLDER WIRE

--

++

++

--

7. Connect the Auto-feed Iron to the station

and switch it on. Lift the auto-feed iron from

the stand and press the WIRE LOAD key until

Fast wire

dragging

Solder wire dragging button

Guide tube

A. Adjust the dragging strength to allow the

forwarding of the solder wire and to avoid

stall and or clogging situations when any

cause arises.

Clutch Regulation

A

B

the solder wire comes out of the end of the

guide tube.

B. Tighten the dragging mechanism.

www.jbctools.com

5

When using solder wire within Ø 1.1 and Ø 1.8 mm you must use the drivergear (ref. 0002863) for

the dragging system to function properly. This gear replaces the one supplied with the station. To

do this,follow these instructions:

1. Open the dragging mechanism.

1

Driver Gear Replacement

6

2. Unscrew the clutch regulation assembly

and pull it out.

3. Pull out the standard driver gear supplied

with the station.

4. Place the new driver gear (ref. 0002863)

supplied with the guide set.

5. Place the regulation assembly and screw it.

Close the dragging mechanism.

www.jbctools.com

7

This product should not be thrown in the garbage.

In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must

be collected and returned to an authorized recycling facility.

Warranty

JBC’s 2 year warranty covers this equipment against

all manufacturing defects, including the replacement

of defective parts and labour.

Warranty does not cover product wear or misuse.

In order for the warranty to be valid, equipment must

be returned, postage paid, to the dealer where it was

purchased.

Get 1 extra year JBC warranty by registering here:

https://www.jbctools.com/productregistration/

within 30 days of purchase.

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

0 0 0 4111- 0 8 0 124

Speciﬁcations

GAL0405, GAL0608, GAL0910, GAL1115, GAL1618

Guide Kit for AL250

Ref. 0002399 - Ø 0.4 - 0.5 mm / 0.015 - 0.02 in

Ref. 0002402 - Ø 0.6 - 0.8 mm / 0.023 - 0.03 in

Ref. 0002401 - Ø 0.9 - 1 mm / 0.035 - 0.04 in

Ref. 0002843 - Ø 1.1 - 1.5 mm / 0.043 - 0.06 in

Ref. 0013915 - Ø 1.6 - 1.8 mm / 0.062 - 0.07 in

- Net weight: 28g / 0.06lb

- Package dimensions / weight: 245 x 185 x 45 mm / 100 g

(L x W x H) 9.65 x 7.28 x 1.77 in / 0.22 lb

Complies with CE standards.

ESD Safe.