JB Systems RAVE BAR Manual de usuario

ENGLISH USER MANUAL

JB SYSTEMS®1/10 RAVE BAR

OPERATION MANUAL

Thank you for buying this JB SYSTEMS®product. To take full advantage of all possibilities and for your own

safety, please read these operating instructions very carefully before you start using this unit.

FEATURES

•3 effects in one single unit !

•14x3W Warm White Leds

•120 SMD RGB Leds

•180 SMD Cold White Leds

•Prepared for wireless DMX: just plug-in an optional WTR-DMX DONGLE ! (optional, Briteq® code 4645)

•Multiple working modes:

•DMX-control: via 1, 2, 6, 34 or 37 channels

•Standalone: sound activated with internal mic

•Master/slave: wonderful synchronized lightshows.

•4-digit LED-display for easy menu navigation

BEFORE USE

•Before you start using this unit, please check if there’s no transportation damage. Should there be any, do

not use the device and consult your dealer first.

•Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary

for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused

by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects

or problems caused by disregarding this user manual.

•Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user

manual.

Check the contents:

Check that the packing contains the following items:

•Operating instructions

•RAVE BAR

•Mains cable

ENGLISH USER MANUAL

JB SYSTEMS®2/10 RAVE BAR

SAFETY INSTRUCTIONS:

•To protect the environment, please try to recycle the packing material as much as possible.

•To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

•To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or may even cause damages.

•This unit is for indoor use only.

•Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign

object enters the unit, immediately disconnect the mains power.

•Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture

must be fixed at least 50cm from surrounding walls.

•Don’t cover any ventilation openings as this may result in overheating.

•Prevent use in dusty environments and clean the unit regularly.

•Keep the unit away from children.

•Inexperienced persons should not operate this device.

•Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.

•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

•Allow the device about 10 minutes to cool down before to start servicing.

•Always unplug the unit when it is not used for a longer time or before to start servicing.

•The electrical installation should be carried out by qualified personal only, according to the regulations for

electrical and mechanical safety in your country.

•Check that the available voltage is not higher than the one stated on the unit.

•The power cord should always be in perfect condition. Switch the unit immediately off when the power cord

is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

•Never let the power-cord come into contact with other cables!

•This fixture must be earthed in order to comply with safety regulations.

•Don’t connect the unit to any dimmer pack.

•Always use an appropriate and certified safety cable when installing the unit.

•In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.

•Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same

type and electrical specifications!

•In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

•The housing and the lenses must be replaced if they are visibly damaged.

•Please use the original packing when the device is to be transported.

CAUTION: To reduce the risk of electric shock, do not remove

the top cover. No user-serviceable parts inside. Refer servicing

to qualified service personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the

use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence

of important operation and maintenance (servicing) instructions in the literature accompanying

this appliance.

This symbol means: indoor use only

This symbol means: Read instructions

This symbol determines: the minimum distance from lighted objects. The minimum distance

between light-output and the illuminated surface must be more than 0.1 meter

The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for

mounting on non-combustible surfaces)

CAUTION: Do not stare at operating lamp.

May be harmful to the eyes.

ENGLISH USER MANUAL

JB SYSTEMS®3/10 RAVE BAR

•Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering

from epilepsy.

DESCRIPTION:

1. BRACKET: with knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook.

2. DMX INPUT: 3pin male XLR-connector used to connect the projector with the DMX controller or with the

previous unit in the DMX chain.

3. MAINS INPUT: with ProCon socket, connect the supplied mains cable here.

4. [MENU] button: used to browse the different functions in the menu.

5. [▲] button: to increase the values shown on the display.

6. [▼]button: to lower the values shown on the display.

7. [ENTER] button: used to confirm your choice or to enter the setup mode of a function.

8. M-DMX INPUT: Please note that this USB-connector is NOT used for updates or to connect the unit to a

PC! Instead this USB-connector makes it very easy to add wireless DMX to the unit! Just add the

(optional) WTR-DMX DONGLE from BRITEQ®and you will get wireless DMX! Moreover you will be able

to connect other DMX-controlled equipment to the DMX-output so you can share the wireless DMX

function with all connected units! No extra settings to be made in the setup menu, just follow the

procedure in the user manual supplied with the WTR-DMX DONGLE from BRITEQ®. The separate

WTR-DMX DONGLE is available from WWW.BRITEQ-LIGHTING.COM (order code: 4645)

9. MAINS OUTPUT: with ProCon connector. You can use a special XLR/Powercon cable to connect up to

max. 16A (power).

10. DMX OUTPUT: 3pin female XLR-connector used to connect the projector with the next unit in the DMX

chain.

11. DISPLAY shows the various menus and the selected functions.

OVERHEAD RIGGING

•Important: The installation must be carried out by qualified service personal only. Improper

installation can result in serious injuries and/or damage to property. Overhead rigging requires

extensive experience! Working load limits should be respected, certified installation materials

should be used, the installed device should be inspected regularly for safety.

•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

•The device should be installed out of reach of people and outside areas where persons may walk by or be

seated.

•Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s

weight.

•Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.

This secondary safety attachment should be installed in a way that no part of the installation can drop

more than 20cm if the main attachment fails.

•The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!

•Don’t cover any ventilation openings as this may result in overheating.

•The operator has to make sure that the safety-relating and machine-technical installations are approved by

an expert before using them for the first time. The installations should be inspected every year by a skilled

person to be sure that safety is still optimal.

ENGLISH USER MANUAL

JB SYSTEMS®4/10 RAVE BAR

ELECTRICAL INSTALLATION

Important: The electrical installation should be carried out by qualified personal only,

according to the regulations for electrical and mechanical safety in your country.

Electrical installation for 1 standalone unit:

•Insert the mains cable. The unit starts working immediately in the last selected mode.

•Refer to chapter HOW TO SETUP to learn how to switch between the different working modes.

Electrical installation for two or more units in master/slave:

•Connect the units together using good quality balanced microphone cables. The unit that has no cable

connected to its DMX-input is the “master”, the others are the slave units.

•Make sure that all units are connected to the mains.

•Refer to chapter HOW TO SETUP for more information.

Electrical installation for two or more units in DMX-mode:

•The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to

“daisy chain” your DMX controller and all the connected units with a good quality

balanced cable.

•To prevent strange behavior of the light effects, due to interferences, you must use

a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this

simply won’t work!

ENGLISH USER MANUAL

JB SYSTEMS®5/10 RAVE BAR

•Make sure that all units are connected to the mains.

•Each light effect in the chain needs to have its proper start address so it knows which commands from

the controller it has to decode. In the section HOW TO SETUP you will learn how to set the DMX

addresses. Remember that each projector uses 2 channels, a possible address setup could be: unit1 =

001 ~ unit2 = 003 ~ unit3 = 005 ~ unit4 = 007 ~ etc.

HOW TO SETUP:

MAIN MENU:

•To select any of the menu options, press the

[MENU] button up to when the required option is

shown on the display.

•Use the [▼] and [▲] buttons to change the

parameters of the mode.

•Use the [ENTER] button to confirm your setting

DMX512 Address + DMX mode + DMX fail mode

Settings

Used to set the start address + the DMX mode in

a DMX setup.

You can also set how the projector should react

in case there would be a DMX signal failure.

•Press the [MENU] button until [Addr] is shown on

the display.

•Use the [▼] and [▲] buttons to change the

DMX512 address.

•Press the [ENTER] button to confirm your setting

•Use the [▼] and [▲] buttons to select the desired

DMX mode (1ch, 2ch, 6ch, 34ch or 37ch mode).

•Press the [ENTER] button to confirm your setting

•Use the [▼] and [▲] buttons to select the desired

DMX fail mode:

o[bLC]: when the signal is lost, the

projector will go in Blackout mode

(no light output)

o[HOLd]: when the signal is lost, the

projector will keep on working

according to its last received

command.

•Press the [ENTER] button to confirm your setting

SLAVE MODE

When you have one projector working in

standalone mode (without DMX controller), you

can connect other Rave Bars to this unit and put

them in SLAVE mode so they will do exactly the

same things as the first (master) projector.

•To put a projector in SLAVE mode, just press the

[MENU] button until SLAU is shown on the

display.

•Press the [ENTER] button to confirm your setting

STANDALONE MODE:

You can use the projector without DMX controller

and set the desired parameters manually.

1. FIXED DIMMER LEVEL AND STROBE

SPEED

•Press the [MENU] button until [CoLo] is shown on the display.

•Press [ENTER] to confirm your choice.

ENGLISH USER MANUAL

JB SYSTEMS®6/10 RAVE BAR

•Use the [▼] and [▲] buttons to set the intensity of the light output for the selected color (00=blackout,

255=max. output).

o[r000 –r255] : red

o[g000 –g255] : green

o[b000 –b255] : blue

o[u000 –u255] : 14 x 3W warm white LEDs

o[S000 –S255] : 180 cool white SMD LEDs

o[St_0 –St_9] : strobe speed ALL LEDs

•Press the [ENTER] button to confirm your setting

2. SOUND MODE

Used to set the automatic Sound Controlled Mode.

•Press the [MENU] button until [Soud] is shown on the display.

•Use the [▼] and [▲] buttons to set the desired sound mode [Sou1 –Sou4]

•Press [ENTER] to confirm your setting.

•[SEn1 –Sen9] : sensitivity of the build-in microphone ([Sen1]=low sensitivity, [SEn9]=high sensitivity).

•Press [ENTER] to confirm your setting.

OPERATING INSTRUCTIONS

A. Standalone 1unit:

•Just connect the projector to the mains.

•Select the desired STANDALONE MODE ([Shou –Soud –Colo –StAt])

•Refer to chapter HOW TO SETUP to learn how to make the settings.

B. Two or more units in master/slave setup:

•Connect several units together. Refer to the chapter “electrical installation” to learn how to do this.

•Select one of the STANDALONE MODES on the master (the first Rave Bar in the DMX chain)

•Set all the other projectors in SLAVE mode.

•The projectors will now follow the program of the master projector so they all work synchronously.

C. Controlled by universal DMX-controller:

•Connect all units together. Refer to the chapter “Electrical installation for two or more units in DMX-

mode” to learn how to do this (don’t forget to address all units properly!)

•Connect all units to the mains and turn on the DMX controller.

Since each unit has its own DMX-address, you can control them individually. Remember that each unit

uses 1, 2, 6, 34 or 37 DMX-channels, depending on the DMX-mode you have selected in the menu. See

the different DMX charts below:

DMX Charts

1CH Mode :

DMX

Channel

DMX-value

function

remarks

000-009

No function

010-044

Auto program 1

Random, slow->fast

045-079

Auto program 2

14x3W WW + RGB, slow->fast

080-114

Auto program 3

14x3W WW + 180xCW, slow->fast

115-149

Auto program 4

RGB + 180xCW, slow->fast

150-184

Auto program 5

14x3W WW, slow->fast

185-219

Auto program 6

RGB, slow->fast

220-254

Auto program 7

180xCW, slow->fast

255

Sound mode

ENGLISH USER MANUAL

JB SYSTEMS®7/10 RAVE BAR

2CH Mode :

DMX

Channel

DMX-value

function

remarks

000-009

No function

010-044

Auto program 1

Random, slow->fast

045-079

Auto program 2

14x3W WW + RGB, slow->fast

080-114

Auto program 3

14x3W WW + 180xCW, slow->fast

115-149

Auto program 4

RGB + 180xCW, slow->fast

150-184

Auto program 5

14x3W WW, slow->fast

185-219

Auto program 6

RGB, slow->fast

220-254

Auto program 7

180xCW, slow->fast

255

Sound mode

000-255

Speed

Program 1-7, slow->fast

6CH Mode :

DMX

Channel

DMX-value

function

remarks

000-255

Dimmer

000-009

14x3W WW LEDs OFF

010-019

14x3W WW LEDs ON

020-029

14x3W WW program 1

030-039

14x3W WW program 2

040-049

14x3W WW program 3

050-239

…

240-255

14x3W WW program 23

000-009

RGB LEDs OFF

010-021

Static color 1

022-033

Static color 2

034-045

Static color 3

046-057

Static color 4

058-069

Static color 5

070-081

Static color 6

082-093

Static color 7

094-105

Static color 8

106-117

Static color 9

118-129

Static color 10

130-141

RGB LEDs program 1

142-153

RGB LEDs program 2

154-165

RGB LEDs program 3

166-177

RGB LEDs program 4

178-189

RGB LEDs program 5

190-201

RGB LEDs program 6

ENGLISH USER MANUAL

JB SYSTEMS®8/10 RAVE BAR

202-213

RGB LEDs program 7

214-225

RGB LEDs program 8

226-237

RGB LEDs program 9

238-249

RGB LEDs program 10

250-255

RGB LEDs program 11

000-009

CW LEDs OFF

010-027

CW LEDs ON

028-045

CW LEDs program 1

046-063

CW LEDs program 2

064-243

…

244-255

CW LEDs program 13

000-255

Speed

Slow->fast

000-009

No function

010-255

Strobe

Slow->fast

34CH/37CH Mode :

DMX

Channel

DMX-value

function

remarks

000-255

3W WW LED1

000-255

3W WW LED2

000-255

3W WW LED3

000-255

3W WW LED4

000-255

3W WW LED5

000-255

3W WW LED6

000-255

3W WW LED7

000-255

3W WW LED8

000-255

3W WW LED9

000-255

3W WW LED10

000-255

3W WW LED11

000-255

3W WW LED12

000-255

3W WW LED13

000-255

3W WW LED14

000-255

RGB-1 RED

000-255

RGB-1 GREEN

000-255

RGB-1 BLUE

000-255

RGB-2 RED

000-255

RGB-2 GREEN

000-255

RGB-2 BLUE

000-255

RGB-3 RED

000-255

RGB-3 GREEN

000-255

RGB-3 BLUE

000-255

RGB-4 RED

000-255

RGB-4 GREEN

Tabla de contenidos

Otros manuales de Equipo de DJ de JB Systems

JB Systems

JB Systems COB-4BAR Manual de usuario

JB Systems

JB Systems LED Rotogobo Manual de usuario

JB Systems

JB Systems MCD 150 Manual de usuario

JB Systems

JB Systems BL-B18 Manual de usuario

JB Systems

JB Systems beat 6 mk2 Manual de usuario

JB Systems

JB Systems UV-400 Manual de usuario

JB Systems

JB Systems SPACE-4 Mk2 LASER Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

JB Systems

JB Systems Dj-kontrol 3 Manual de usuario

JB Systems

JB Systems MULTIBEAM LASER Manual de usuario

JB Systems

JB Systems USB PARTYSET Manual de usuario

JB Systems

JB Systems LIVESET 2 Manual de usuario

JB Systems

JB Systems RAVE SPOT Manual de usuario

JB Systems

JB Systems SPYDER-RGB LASER Manual de usuario

JB Systems

JB Systems PlanoSpot 7TC Manual de usuario

JB Systems

JB Systems CD 100 Manual de usuario

JB Systems

JB Systems INTRUDER Manual de usuario

JB Systems

JB Systems mix 3 USB Manual de usuario

JB Systems

JB Systems Sunbar White Manual de usuario

JB Systems

JB Systems BEAT6 Mk2 Manual de usuario

JB Systems

JB Systems CLUB7USB Manual de usuario

JB Systems

JB Systems DJ-kontrol 2 Manual de usuario

JB Systems

JB Systems PARTY SPOT Manual de instalación

JB Systems

JB Systems Led Globe Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario

KAM

KAM DMX Laser80 FScan Manual de usuario