Jasic TIG Series Manual de usuario
2
Your new product
Thank you for selecng this Jasic product.
This product assembly manual has been designed to ensure that you get the most from your new
product. Please ensure that you are fully conversant with the informaon provided paying parcular
aenon to the safety precauons which can be found in the Jasic machine operang manual. The
informaon provided within the assembly manual and the product operang manual will help protect
yourself and others against the potenal hazards that you may come across.
Please ensure that you carry out daily and periodic maintenance checks to ensure years of reliable and
trouble free operaon.
Please call your Jasic distributor in the unlikely event of a problem occurring.
Please record below the details from your product as these will be required for warranty purposes (if
applicable) and to ensure you get the correct informaon should you require assistance or spare parts.
Date purchased ________________________________________
From where ________________________________________
Serial number ________________________________________
The serial number (if applicable) is normally located on the top or underside of the machine and will
begin with AA) and for further informaon on your Jasic product warranty registraon please visit:
www.jasic-warranty.co.uk
Disclaimer
Whilst every eort has been made to ensure that the informaon contained within this manual is
complete and accurate, no liability can be accepted for any errors or omissions.
Please note:
Products are subject to connual development and may be subject to change without noce.
Regularly check our product pages at www.Jasic.co.uk for revision updated operang manuals.
No part of this manual may be copied or reproduced by any means without the wrien permission of
Wilkinson Star Limited.
3
TIG TROLLEY COMPATABILITY
These assembly instrucons are suitable for the following Jasic TIG welding packages:
JT-202A-WC
JT-202D-WC
JT-300P-WC
JT-315MWD-WC
CONTENTS
Check the trolley packaging for any signs of damage.
Carefully remove all the components, check that all parts are present and retain the packaging unl the
assembly is complete.
Kit Contents:
1 x Base Unit (assembled) 2 x Cylinder Chain/Straps 2 x Side xing brackets
1 x Upright Cylinder Support 2 x Top Shelf Brackets 1 x Top unit (with handle)
6 x M5 Screws 10 x M10 Screws 12 x M6 Screws
Please Note: This kit is used for other machine packages, you may note that extra screws are supplied and
as a result there may be some screws le over once you have fully assembled the trolley package.
For the following instrucons we have used the Jasic JT-315 ACDC Mul Wave TIG power source and
cooler as shown below.
4
CONTENTS
The below shows the main contents of the TIG trolley assembly kit.
Various sundry items (required for assembly)
Base unit (item 1) including assembled wheels Upright Cylinder Support (item 3)
Side xing brackets (item 4)
Top shelf (item 2) also showing circled top shelf brackets
5
ASSEMBLY
1Place the base unit on a at surface, locate the 2 Locate the cooler base brackets (circled
cylinder support (Item 3) and use M10 screws (A) yellow) which secures the water cooler to
to x the cylinder support to the base unit (item1). the base unit. (brackets supplied with cooler)
3Place the cooler on its side and mount the two brackets supplied with the water cooler (circled
yellow) to the boom of the cooler as shown using the screws (B) supplied with the cooler.
Please Note: Fit the front bracket to the holes that are more central on the boom of the cooler.
4 Mount and x the water cooler to the base unit (item 1) using the supplied qty 4 screws (B).
6
ASSEMBLY
5Fit the two side brackets (item 4) to the water 6 Fit the TIG wire ‘cup’ (item 5) to the base
cooler as shown below. using the supplied 3 screws (C)
7Remove the boom side front and rear screws either side of the power source (the middle screw may
not be required to be removed) and mount the power source on top of the water cooler lining up the
holes of the bracket. (The bracket should be on the outside of the power source panel). Secure the
power source with the screws that were removed.
7
ASSEMBLY
8Remove the top brackets shown with item 2 9 Mount the top shelf (item 2) on top of the
and t to the top of the power source as shown ed brackets and use the screws removed
below. Use the screws you have removed from earlier to x the top shelf in place. Also secure
the power source lid to x the two brackets in the top shelf (item 2) to the cylinder upright
place. (item 3) with screws (A).
10. Fix (item 6) which assists holding the TIG wire in place, to the top panel (item 2) as shown below using
two screws ©, a 7mm spanner may be required to assist
with fastening this accessory in place.
11. Fit the supplied bole chains (as shown below) through
the relevant slots on item 3 and the assembly is now
complete.
12. Connect the water cooler power plug to the control socket on the rear panel of the TIG power source.
13. Check the relevant TIG machine operang manual for instrucons for ng a water cooled TIG torch.
8
July 2021 - Issue 1
Otros manuales para TIG Series
4
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Sistema de soldadura de Jasic
Jasic
Jasic 315P AC/DC Digital Manual de usuario
Jasic
Jasic MIG 400S Manual de usuario
Jasic
Jasic Arc 140 Manual de usuario
Jasic
Jasic CUT60 (L204) Manual de usuario
Jasic
Jasic EVO 2.0 EP-45 Manual de usuario
Jasic
Jasic Plasma Cut Series Manual de usuario
Jasic
Jasic ARC400 Manual de usuario
Jasic
Jasic EVO 2.0 TR-01 Manual de usuario
Jasic
Jasic Arc 200 PFC Manual de usuario
Jasic
Jasic Plasma Cut Series Manual de usuario
Jasic
Jasic EVO 2.0 LC-30 Manual de usuario
Jasic
Jasic MIG 350P Manual de usuario
Jasic
Jasic L20701 Manual de usuario
Jasic
Jasic MIG 350 Compact Manual de usuario
Jasic
Jasic MIG 250S Manual de usuario
Jasic
Jasic AC/DC315P Guía de inicio rápido
Jasic
Jasic CUT80 (L205) Manual de usuario
Jasic
Jasic MIG250P Manual de usuario
Jasic
Jasic Power Arc 160 PFC Manual de usuario
Jasic
Jasic EVO 2.0 EM-200CT Manual de usuario
Manuales populares de Sistema de soldadura de otras marcas
TAFA
TAFA 30*8B35 Manual de usuario
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manual de usuario
ESAB
ESAB Buddy Arc 145 Manual de usuario
CIGWELD
CIGWELD 636804 Guía rápida
Red-D-Arc
Red-D-Arc DC-400 Manual de usuario
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario
