Jasic Plasma Cut 45 Manual de usuario

Jasic Cut 45

PT60 Plasma Hand Torch Manual

Wilkinson Star Technical

Contents Page

Before starng any cung acvity thoroughly read the operang manual rst to familiarize yourself with the safe and correct

operaon of your Jasic plasma machine. Always ensure that you have suitable eye protecon and protecve clothing. Also take

the necessary steps to protect any persons within the cung area.

Index Page Number

Jasic Cut 45 with PT60 Plasma Torch Overview 3

PT60 Consumable Breakdowns 4

PT60 Torch Informaon 7

Machine torch opon 8

Safety Informaon 9

General Plasma Cung Informaon 10

Stand-o Cung 11

Drag Cung 12

Piercing 13

Bevelling 13

Gouging 14

Cung Tips and Techniques 15

Plasma Machine Gas Supply - Compressed Air 16

Notes 17

Contact Details 18

Jasic Cut 45 Plasma Cung Machine

supplied with PT60 6m Plasma Hand Torch

Wilkinson Star Technical

PT60 (6m Pt No 09637/LG) Torch Specicaons

PT60 (12m Pt No 09639/LG)

Duty Cycle : 60 Amps at 80%

Gas Air Pressure - Cung : 65-75 PSI (4.5 - 5.0 bar)

Gas Air Flow : 360 SCFH (170 lpm)

Pilot Arc Ignion : NON HF

Jasic Plasma Cut 45 Circle Cung

Guide Kit - part number 51866

Item No Part Number Descripon Pack Qty

109603 PT60 Torch Head 1

1A 5162060 Torch head 'O' Ring 1

209605 Handle c/w Switch 1

352582 Electrode - Back Striking 5

460028 Gas Distributor 1

551312P.09 Contact Cung Tip (0.9) 30-40A Back Striking 10

651313P.10 Flat Cung Tip (1.0) 40-50A Back Striking 10

751318.06 Contact Cung Tip (0.65) 10-20A Back Striking 10

751318.08 Contact Cung Tip (0.8) 20-30A Back Striking 10

751318.09 Contact Cung Tip (0.9) 30-40A Back Striking 10

852583 Extended Electrode Back Striking 10

10 51314.09 Extended Tip Contact (0.9) 30-40A Back Striking 10

11 51318L.06 Extended Tip Contact (0.65) 10-20A Back Striking 10

11 51318L.08 Extended Tip Contact (0.8) 20-30A Back Striking 10

12 51318C.09 Shielded Cung Tip (0.9) 30-40A Back Striking 10

12 51318C.10 Shielded Cung Tip (1.0) 40-50A Back Striking 10

14 60389 Retaining Cap 1

14 60389S Retaining Cap (long life) 1

16 60389C Shield Cup Body 1

18 60432 Double Pointed Spacer (for items 6 & 7 only) 1

19 60485 Shield Cap, Hand 1

21 60368 Wrench for Electrode 1

Jasic Cut 45 Plasma with PT60 6m Hand Torch

Wilkinson Star Technical

Jasic Cut 45 with PT60 plasma hand torch

Stand o and exposed contact p cung setup

Item No Part Number Descripon Pack Qty

109603 PT60 Torch Head 1

1A 5162060 Torch head 'O' Ring 1

209605 Handle c/w Switch 1

352582 Electrode - Back Striking 5

460028 Gas Distributor 1

551312P.09 Contact Cung Tip (0.9) 30-40A Back Striking 10

651313P.10 Flat Cung Tip (1.0) 40-50A Back Striking 10

751318.06 Contact Cung Tip (0.65) 10-20A Back Striking 10

751318.08 Contact Cung Tip (0.8) 20-30A Back Striking 10

751318.09 Contact Cung Tip (0.9) 30-40A Back Striking 10

10 51314.09 Extended Tip Contact (0.9) 30-40A Back Striking 10

11 51318L.06 Extended Tip Contact (0.65) 10-20A Back Striking 10

11 51318L.08 Extended Tip Contact (0.8) 20-30A Back Striking 10

14 60389 Retaining Cap 1

14 60389S Retaining Cap (long life) 1

18 60432 Double Pointed Spacer (for items 6 & 7 only) 1

21 60368 Wrench for electrode 1

Wilkinson Star Technical

Jasic Cut 45 with PT60 plasma hand torch

Drag cap cung (enclosed p) setup

Wilkinson Star Technical

Item No Part Number Descripon Pack Qty

109603 PT60 Torch Head 1

1A 5162060 Torch head 'O' Ring 1

209605 Handle c/w Switch 1

352582 Electrode - Back Striking 5

460028 Gas Distributor 1

852583 Extended Electrode Back Striking 10

12 51318C.09 Shielded Cung Tip (0.9) 30-40A Back Striking 10

12 51318C.10 Shielded Cung Tip (1.0) 40-50A Back Striking 10

16 60389C Shield Cup Body 1

19 60485 Shield Cap, Hand 1

21 60368 Wrench for electrode 1

PT60 Plasma Hand Torch

Wilkinson Star Technical

The PT60 plasma torch supplied has the ‘euro style’ power/gas connecon, pilot cable and switch pins connecons.

All Jasic plasma cung systems and torches supplied incorporate a safety circuit to prevent operator injury when

changing consumables etc. This is a simple ring circuit that breaks the electrical torch switching as soon as the

retaining cap is removed prevenng machine operaon. Without such a protecon circuit as previously menoned

the open circuit voltage could be as high as 350V DC at the torch head.

The torch head encompasses a full set of consumables as shown right, these consumables are made

up of a cooling tube, torch electrode, swirl ring for gas distribuon, cung p, retaining cap and if

required a stand o device to ensure the same distance between p and material being cut.

Fing the PT60 plasma torch

On the Jasic Cut 45 plasma machine, the below torch ng instrucons

will need to be observed.

• Locate plasma torch plug into euro connector socket as shown in

image 1 below

• Push the torch (image 1) whilst at the same me rotate the locking

nut on torch clockwise unl fully connected and ght as in image 2

below

Image 1 Image

Plasma Torch Connecon Diagram

Current : 40 - 125 Amps

Duty Cycle : 125 Amps at 60%

Gas : Air/N2

Gas Pressure - Cung : 72-87 PSI (5.0-6.0 bar)

Gas Flow @ 125A : 630 SCFH (295 lpm)

Post Flow Time : 45 Seconds

Pilot Arc Current : 15 - 18Amps

Pilot Arc Ignion : NON HF

Wilkinson Star Technical

Item No Part Number Descripon Pack Qty

103710 Torch Head 1

1a 03700.60 Torch Head ‘O’ Ring 10

207218 Posioning Tube 1

3220857 Swirl Ring (45-85A) Max Life 1

552677 Electrode (45/105A) 5

6220930 Cung Tip (45A Precision Cut) 10

7220941 Cung Tip 45A) 10

11 60309TA Shield Cup Body (45-85A) 1

13 51929 Shield Cap (45A) Precision Cut 1

14 220817 Machine Shield (45-85A) 1

16 07219 Posioning Tube With Rack 1

17 60309THA Shield Cup Body (45-85A)

C/W Ohmic Clip 1

Please Note: Conguraon above only to be used on the Jasic Cut 45

Plasma Machine Torch - TM125 6m - Euro (Pt No 70061)

TM125 12m - Euro (Pt No 03736CX)

Plasma Cung Safe Working Pracce

Safety glasses must be worn at all times in addition to welding mask Long and loose hair must be contained

Oil free leather gloves and spats must be worn Sturdy footwear with rubber soles must be worn

Close fitting/protective clothing to cover arms and legs must be worn A welding mask with shade number 11 protective filters must be worn

Respiratory protection devices may be required Hearing protection may be required when cutting thick material

PRE-OPERATIONAL SAFETY CHECKS

• Locate and ensure you are familiar with all machine operaons and controls.

• Ensure material to be cut poses no hazard. Consult the manufacturers' Material Safety Data Sheets (MSDS) for specic technical data and precauonary measures for any materials or

coangs on materials cut with this equipment.

• Check workspaces and walkways to ensure no slip/trip hazards are present, ensure the work leads and hoses do not create a trip hazard.

• Ensure the work area is clean and clear of grease, oil and any ammable materials.

• Keep the equipment, work area and your gloves dry to avoid electric shocks.

• Ensure the gloves, handpiece and work leads are in good condion.

• Ensure other people are protected from ashes by closing the curtain to the welding bay or erecng screens.

• Start the fume extracon unit before beginning cung operaon. Ensure machine is used in a well-venlated area if not used in a welding bay.

OPERATIONAL SAFETY CHECKS

• Ensure machine is correctly set up for current and airow.

• Ensure work return earth cables make rm contact to provide a good electrical connecon.

ENDING OPERATIONS AND CLEANING UP

• Switch o the machine and fume extracon unit when work completed.

• Turn o the air supply and hang up handpiece, hose and welding cables.

• Leave the work area in a safe, clean and dy state.

DON’T

• Do not use faulty equipment. Immediately report suspect equipment.

• Do not weld or cut containers that have held combusble liquids or gases.

• Do not heat or cut metals coated with or containing materials that emit toxic fumes, unless coang is removed from the work surface.

• Never leave the machine running unaended.

This safety page does not necessarily cover all possible hazards associated with plasma equipment safety and should be used in conjuncon with the operang manual along

with other references such as risk assessments. It is designed as a reminder to users prior to equipment use and as a guide to be used to compliment operator training.

POTENTIAL HAZARDS AND INJURIES

 Electric shock

 Noise

 Body burns

 Compressed air

 Radiaon burns

 Fumes

 Noxious gas

 Flying sparks and falling slag

Wilkinson Star Technical

General Plasma Cung Informaon

Before starting any welding or cutting activity ensure that you have suitable eye protection and

protective clothing. Also take the necessary steps to protect any persons within the welding area.

Notes for cung operaon

 Do not touch the hot workpiece with bare hands to avoid burning.

 It is recommended not to ignite the arc in the air if not necessary, for it will shorten the lifespan of the electrode and nozzle of the torch.

 It is recommended to iniate the cung from the edge of the workpiece unless penetraon is needed.

 Ensure spaer comes from the boom of workpiece while cung. If spaer comes upwards from the top of workpiece, it indicates that the

workpiece has not been fully cut through. This could be due to not enough power or the cung torch is moved too fast.

 For cung a round or shaped piece or to meet precise cung requirement, a stencil board or other tools are needed.

 It is recommended to pull the cung torch while cung.

 Keep the nozzle of the cung torch upright over the workpiece and check if the arc is moving with the cung line. Do not bend the cable too

much, step on or press upon the cable to avoid restricng the air ow. The cung torch may be burned if the air ow is too low. Keep the cung

cable away from sharp edges.

 When the workpiece is nearly cut o, slow down the cung speed and release the torch trigger to stop cung.

 Check the torch consumables frequently to prolong the life.

 Always ensure the correct consumables are ed in the torch. Incorrect items may cause damage to the torch or machine.

 It is recommended that a torch of maximum length of 6 metres is used. If the torch cable is too long, the performance of this cung machine

such as arc ignion will possibly be aected due to the fact that the inner resistance of the cable will reduce the output voltage.

• Please Note:

• Your air supply must be free of moisture, water, oil or any other contaminants. Excessive water or oil may cause double arcing, excessive

electrode/p wear or even torch head failure. Contaminants will also cause poor cut quality.

• When starng the arc, ensure you keep the pilot arc me to a minimum to avoid excessive wear on the cung p.

• Do not overghten the electrode when ng a new set of consumables. Over ghtening may cause damage to the internal torch head thread

so that the cung p will not seat correctly.

• Only use the supplied or recommended ’O’ ring lubricant or grease for your plasma torch head, using the wrong lubricant that cannot

withstand high temperatures could cause damage to the plasma torch head.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de Jasic

Jasic

Jasic TIG200PACDC PFC Manual de usuario

Jasic

Jasic L20701 Manual de usuario

Jasic

Jasic Arc 140 Manual de usuario

Jasic

Jasic AC/DC315P Guía de inicio rápido

Jasic

Jasic EVO 2.0 Manual de usuario

Jasic

Jasic TIG 200 AC/DC Digital Series Manual de usuario

Jasic

Jasic MIG 200 PFC Manual de usuario

Jasic

Jasic EVO 2.0 EM-200CT Manual de usuario

Jasic

Jasic EVO 2.0 LC-30 Manual de usuario

Jasic

Jasic TIG Series Manual de usuario

Jasic

Jasic EVOLVE200 PLUS Manual de usuario

Jasic

Jasic EVO 2.0 EM-160C Manual de usuario

Jasic

Jasic MIG SERIES Manual de usuario

Jasic

Jasic Cut 160 Manual de usuario

Jasic

Jasic MIG 270 Separate Manual de usuario

Jasic

Jasic MIG 350C Manual de usuario

Jasic

Jasic Plasma Cut 100 Manual de usuario

Jasic

Jasic MIG 350 Compact Manual de usuario

Jasic

Jasic Cut 81 Manual de usuario

Jasic

Jasic ARC PFC Series Manual de usuario

Jasic

Jasic MIG SERIES Manual de usuario

Jasic

Jasic TIG 200 P AC-DC Guía de inicio rápido

Jasic

Jasic TIG 200 AC/DC Analog Manual de usuario

Jasic

Jasic TIG 200 Dual Voltage Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario