IWILL P55TU Manual de usuario

EC Declaration of Conformity

Iwill Corp.

No. 9-1, Kong 6th RD.,

Lin Kou 2nd Industrial

Park, Taipei, Taiwan R.O.C.

declare under sole responsibility that the

P55TU motherboard

meets the intent of Directive 89/336/ECC forElectromagnetic Compatibility.

Compliance was demonstrated to the followingspecificationsas listed in the

official Journal of the European Communities:

EN 50081-1Emissions:

EN 55022 Radiated, Class B

EN 55022 Conducted, Class B

EN 60555-2 Power Harmonics

EN 50082-1Immunity:

IEC 801-2 Electrostatic Discharge

IEC 801-3 RF Radiat

IEC 801-4 Fast Transient

About this manual

This P55TU SCSI Motherboard is the newest memberto our SCSI Motherboard

solution products families. It incorporated with Intel4th generation 430HX

Chipset with BGA technology and with Adaptecnew Ultra / Ultra Wide SCSI

embedded which is equilevent to AHA 2940UW. AdaptecRAID port option

ready is a big advantage in this P55TU SCSI motherboard.It can turn this SCSI

motherboard to support hardware SCSI RAID by addingthe RAIDBUS 1000 or

the ARO 1130 adapterfrom Adaptec.

Run with fasterCPU is very important function that thisSCSI Motherboard support.

It support bothP54C up to 200 MHz* and Intel’s next generation P55C processor

with MMX technology.

Feature with Error Check Correction ( ECC ) system memory is another plus on

this SCSI Motherboard to outperform the whole system stability. It equipe 4 of the

72 pin SIMM that supportsEDO DRAM with ECC.

This manualis subject to change without notice.

This manualcontainsinformation protected by copyright law. All rights are

reserved. No any partof this document may be used or reproduced in any forms

or by any means,or stored in a database orretrieval system, without prior written

permission.

Trademark

Intel

/ Pentium is trademark of Intel

Corporation and all other product names

are trademarksandregistered trademarksof their respective owners.

Warning

This motherboard is carefully designed with Intelspec. to fully supportP54C

processor up to 200Mhzand thenew P55C. Since Intel is notshiping theP54C

with 200Mhz and the new P55C CPU at the point that we deliver this

motherboard so we hold theresponsibility on if Intelchange any spec. that cause

the new processor not function properly in this motherboard.

iii

Contents

Chapter 1- Overview

1.1 Features P1

1.2 Specifications P3

Chapter 2- Quick Installation P4

Chapter 3- Hardware Installation

3.1 Preparation and Inspection P6

3.2 Placement P8

3.3 CPU group P10

3.4 Cache Memory P13

3.5 D-RAM Configuration P14

3.6 SCSI Interface P14

3.7 Adaptec RAIDport option P17

3.8 IDE Interface P18

3.9 USB P19

3.10 Enhanced Multi-IO P19

3.11 Other P20

Chapter 4- Award BIOS Setup

4.1 Main Menu P26

4.2 Standard CMOS Setup P29

4.3 BIOS Features Setup P33

4.4 Chipset Feature Setup P39

4.5 Power Management Setup P46

4.6 PNP/PCI Configuration P50

4.7 Integrated Peripherals P52

4.8 Load Setup Defaults P54

4.9 Supervisor/User Password P54

4.10 IDE HDD Auto Detection P55

4.11 HDD Low Level Format P55

4.12 Save & Exit Setup P55

4.13 ExitWithout Saving P55

Chapter 5- SCSI BIOS Setup

5.1 When to Use the SCSI Select Utility P56

5.2 SCSI Select Utility option P57

5.3 Configure / View Host AdapterSettings Menu P57

5.4 SCSI Disk Utilities P64

CHAPTER1

Overview

Thank you for purchasing this P55TU SCSI Motherboard. This operation

manualwill guide you to proper configure and install. It has an overview of the

engineer design and feature of this board.Also, this manualprovidesuseful

information foryour later upgrade or change the configuration.Keep this, for

your futureneed.

1.1 Features

This P55TU SCSI Motherboard is a powerfulcombination of performance,

qua lity and innovative design to address the need of today’s ma rket. With current

Intel P54C, Cyrix 6x86,AMD 5k86 and next generation on Intel P55C with

MMX technology supported, 512K externalLevel 2 Pipelined Burst fast Write-

Back Cache,64 bit Burst Bus DRAM and AdaptecWide/Ultra Wide SCSI

(AHA-2940UW ), fully plug and play Super I/O, this SCSI Motherboard brings

exceptionalprocessing power that could only be achieved by Mini-computer.

Incorporatingthe new emerging industrial standard PeripheralComponent

interconnect (PCI) Local Bus together with the standard 16-bit Industrial

Standard Architecture (ISA), this SCSI Motherboard dramatically bootssystem

I/O through for even the most dema nding application in today’s market.

◼CPU:

CPU socket (socket 7) supports theflexibility of differenttype of current

and future Intel Pentium, AMD (5k86) and Cyrix (6x86) processor. One

easy jumperdesign, while choosing your CPU speed from 75 to 200MHz.

◼Cache memories:

High performance write back secondary cache.This supports Pipelined

Burst Cache512K on-board to achieve the highest performance.

◼BIOS:

Award BIOS, on-screen "Plug & Play" setup forAdaptecSCSI, Enhanced

IDE, andSuper multi-IO. Support Flash ROM ( This ROM provides

better upgradeability for user to updatetheirBIOS data on the system

board,user can down-load newer version BIOS from Internet,BBS or get

the diskette file from your vender.

◼Expansion slots:

5 X 16-bits ISA slots.

3 X 32-bits PCI slots for PCI compatible add-on cards.(PCI#2 is occupied

by the AdaptecSCSI, it is flexible for your choosewhile youinstall a prior

or minor controller on this PCI bus.)

◼Memories:

4 X 72-pin SIMM(Single In Line Memory Module)

Support up to 256MB (minimum of 8MB ) on board.for both the Fast

Page Mode and Extended Data Output(EDO) module with ECC support.

◼Ultra/ Ultra Wide SCSIinterface:

⚫Built in Adaptec PCI Ultra Wide SCSI ( AIC 7880chip ) which

is equilevent to Adaptec AHA-2940UW PCI SCSI controller.

⚫Data transfer rate up to 40MB/Sec.

⚫Complete software driver from Adaptec Inc., include EZ-SCSI

for

DOS/Windows, 7800 Family Set Driver forNetware, Windows NT ,

OS/2 , SCO Unix ,

Unixware.

◼IDE functions:

⚫Built in dualPCI Bus EIDE Channels.

⚫Support ATAPI (AT Attachment Packet Interface)

◼USB interface (Universal Serial Bus):

⚫Plug and Play peripherals outside the box

⚫Up to 12Mbit

⚫Easy of use

◼Floppy Interface:

⚫Support both 3 1/2"and 5 1/4" floppy disk drives and Tape Drive

(360K / 720K/ 1.2M / 1.44M / 2.88MB)

⚫Enabled/Disable selectable from system BIOS

⚫Non-Burst Mode DMA Option

⚫Byte Data FIFO

⚫ModeDriver (option)

◼Serial Port

⚫Two high speed 16550 UART serial port

⚫Address changeable form system BIOS

⚫Programmable Baud Rate Generator

◼Parallel Port:

IRQ selectable for IRQ5(278h), 7IRQ(378h) from system BIOS.

Standard mode--Compatiblewith IBM PC/AT Printer port

EPP Mode --Enhanced Parallel Port compatible(EPP) compatible

IEEE 1284

ECP Mode --Microsoft & Hewlett Packard Extended Capabilities Port

(ECP) Compatible

Incorporates Chip Protect Circuit for protection against damage due to

printer power-on

◼Others function:

Support both Fast Page DRAM or EDO DRAM SIMM.

Support Pentium CPU SMM (System Management Mode).

Using Embeded Battery in RTC (Real Time Clock) which provides

environmentalprotection and longer battery life.

1.2 Specifications

◼Physical Dimensions:

Length: 330mm / Width: 220mm

◼Environmental Requirements:

Temperature 0-55 degrees C (operating or storage)

5% to 95% non-condensingrelative humidity

CHAPTER2

Quick Installation

This SCSIMotherboard isshippedwith

manufacturepresetat:

1. CPU Clock at 100 MHz

2. Adaptec Ultra Wide SCSIChip Enabled

3. Wide SCSI Mode Enabled

4. SCSI Terminator Control by BIOS

5. 512K Pipeline Burst Cache on board

6. Printer ECPMode at DMA3

7. Printer at IRQ7, Address at 378h

8. Serial 1 at IRQ4, Serial 2 at IRQ3

9. PS/2 MOUSE at IRQ 12

Referenceto the Chapter 3 & Chapter 4, if you

havedevices conflictwith themanufacture default.

Step 1. Install CPU and Cooler

Makesure the Clock Frequency is set to thesameas theCPU

installed. (Choose the CPU speed by one jumperon JP10)

Step 2. Install the memory

Plug at least 2 PCS of 72 pins Micro Edge DRAM modules

to either Bank0or Bank1.

Step 3. Install display controller and connect I/O ports

This system boardis designed using PCI (Peripheral Component

Interconnect)and ISA (Industry Standard Architecture) interface

controller. This support +5Volt interface slots. All PCI interface

controllers must be PCI Rev 2.1 compliant.

Step 4. Connect the power supply

Connect P8 and P9 from power supply output.

Step 5. Power on the system

Turn on the Computerpower.

Step 6. Setting up the system

Enter the "Setup Menu" screen by press the " Del " key while

power on or warm reset the system.Always "LOAD SETUP

DEFAULT" at first and select others necessary that your

system require.

Step 7. Save the setup data to the CMOS

Exit the"Setup Menu " screen and then write to CMOS RAM.

And enjoy the high performance system board.

Step 8. After boot yoursystem O.S., insert the AdaptecEZ-SCSI

Installation diskette in a floppy disk drive and follow the EZ-

SCSI operation manualorreference to Adaptec 7800 Family

Set manualwhich will guide you to install theDOS/Windows,

Netware, Windows NT, OS/2 , SCO UNIX, Unixware.

CHAPTER3

Hardware Installation

3.1 Preparation and Inspection

The P55TU SCSI Motherboard,like all electronic equipment is static sensitive.

Please take the proper precautionswhen handlingthis board.You should avoid

static up. If possible, You should ground yourself by touchinga metaltable or

your computerframe.Keep the board in its conductive wrapping until it is

configured and ready to be installed in your system.

For installation, you may need some or all of the following tools:

‧SCSIHDD drive/devices manual(s).

‧IDE HDD drive/devices and floppy drive manual(s).

‧Peripherals that connect to your system's manual(s).

‧MS DOS diskettes with FDISKand FORMATprograms.

‧Medium size flat blade screwdriver.

‧Medium sized Phillips head screwdriver.

‧A 3/16 inch nut driver or wrench.

You should find the Following components whenopen thebox :

1. P55TU SCSI Motherboard.

2. This Operation Manual

3. Adaptecsoftware driver Diskette (EZ-SCSI).

4. Adaptec 7800 Family ManagerSet softwaredriver Diskettes.

5. AdaptecEZ-SCSI Manual.

6. Adaptec 7800 Family ManagerSet Manual.

7. 68 pins high density internal Wide SCSI signal flat cable

8. 50 pins internal SCSI signal flat cable.

9. 40 pins internal IDE signal cable.

10. 34 pins internal Floppy Disk Drive signal cable.

11. 10 pins IDC flat cableto 9 pins D-Sub maleRS-232 connector.

12. 26 pins IDC flat cableto 25 pins D-Sub femaleprinter signal flat

cable.

13. 10 pins IDC flat cableto 25 pins D-Sub male RS-232 connector.

14. 1 x 5 pins IDC flat cable to L-frame5 pins PS-2 mouseport.

15. Musical CPU Cooler.

16. External SCSI-2 port expansion kit (optional).

17. External Wide SCSI port expansionkit (optional).

18. High speed printer port software driver(optional).

19. 3 ModeDriver (option)

Tabla de contenidos

Otros manuales de Placa madre de IWILL

IWILL

IWILL WO2 Instrucciones de funcionamiento originales

IWILL

IWILL DPIILS2 Manual de usuario

IWILL

IWILL DP533 Series Manual de usuario

IWILL

IWILL LE370 Manual de usuario

IWILL

IWILL DS133R Manual de usuario

IWILL

IWILL KK400 Series Manual de usuario

IWILL

IWILL VX133u Manual de usuario

IWILL

IWILL piils Manual de usuario

IWILL

IWILL VD133 Manual de usuario

IWILL

IWILL BD100 Plus Manual de usuario

IWILL

IWILL KK266plus-R Instrucciones de funcionamiento originales

IWILL

IWILL IWILL P4D-N Manual de usuario

IWILL

IWILL Motherboard DJ800 Manual de usuario

IWILL

IWILL BS100 Manual de usuario

IWILL

IWILL P4G Series Manual de usuario

IWILL

IWILL DVD266 Manual de usuario

IWILL

IWILL P4E Series Manual de usuario

IWILL

IWILL DVD266u-RN Manual de usuario

IWILL

IWILL VD133 Manual de usuario

IWILL

IWILL dca200 Manual de usuario

IWILL

IWILL PIINS Manual de usuario

IWILL

IWILL DPX2-S320 Manual de usuario

IWILL

IWILL K7S3 Series Manual de usuario

IWILL

IWILL KK266Plus Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario