iWave FPM-8416 Manual de usuario
www.hk-ifly.com
FPM-8416 User Manual
Contents
1 Introduction .................................................................................................................................. 1
2 Connectors and LEDs ...................................................................................................................2
3 Setting up FPM-8416 units ...........................................................................................................5
3.1 Setting up steps of HDMI Video transmitting ................................................................... 5
3.2 Network Configurations .....................................................................................................5
3.3 Setting up steps of Network Communication .................................................................... 6
4 Details and Notice ........................................................................................................................ 7
4.1 TTL Serial Cable ................................................................................................................7
4.2 Ethernet Cable ....................................................................................................................7
4.3 Serial Data Format ............................................................................................................. 8
4.4 Notice ................................................................................................................................. 8
www.iwavecomms.com
１
1 Introduction
FPM-8416 is the model name of middle range (up to 14-16km) point-to-point HDMI （or
SDI）video & network transmission device.
Each set of FPM-8416 contains the following items
One transmitter unit, with a camera logo on it.
One receiver unit, with a monitor logo on it.
Two transmitter-antennas.
Two receiver-antennas, which are longer than transmitter-antennas.
Four antenna-cabls.
One TX side HDMI cable(Or one SDI cables,each cable has two headers , one is
SDI header, one is SMA header to connect FPM-8416), and one RX side HDMI
cable.
Four Power cables.
Four Ethernet cables, each cable has two headers, one is RJ45 header, one is 4P
header to connect FPM-8416.
Two TTL-Serial cables, each cable has two headers, one is 5P header to connect
FPM-8416, one is 3P header to connect external device. Voltage is 3.3V.
Two USB-TTL-Serial dongles.
Each kind of cable is packed in its own transparent bag labeled with model name.
The items may subject to change due to different customer specific configurations.
Please refer “FPM-8416 technical specification” for specifications and parameters.
www.iwavecomms.com
２
2 Connectors and LEDs
Front Side
TX Unit
RX Unit
Camera logo for TX unit, one Mini HDMI port or SDI port.
Monitor logo for RX unit,one Mini HDMI port.
Right Side
One 2P Power connector (Model XT30PW). The voltage range is 7~18V.
www.iwavecomms.com
３
One power switch.
One Power LED, it will be on if power is on.
One WAN LED. It will be flashing if the video stream is transmitting/receiving
over wireless channel
Three wireless status LEDs. LED1 will be on if transmitter unit and receiver unit
are both power on and have established wireless connection successfully.LED2
and LED3 are reserved for production testing.
One SMA connector, to connect an antenna .
One Micro USB connector, it’s reserved for production testing.
Left Side
One 5P serial connector to connect the TTL-serial cable, to transmit serial signal,
voltage is 3.3V.
One SMA connector, to connect an antenna. Both left side and right side SMA
connector should connect to antenna before power on.
TWO LAN connectors.
TWO LAN LEDs. Each is above one LAN connector.
--ON: The LAN connector is connected successfully to external device via a LAN
cable.
--Flashing: Data is transmitting on the LAN connector.
www.iwavecomms.com
４
Rear Side
One standard ¼”-20 screw hole, for installing/mounting the unit on tripod,
platform, etc.
www.iwavecomms.com
５
3 Setting up FPM-8416 units
3.1 Setting up steps of HDMI or SDI Video transmitting
Connect two antennas to transmitter unit by antenna-cables.
Connect two antennas to receiver unit by antenna-cables.
Connect a video source (video camera, camcorder, etc) to transmitter unit by TX
side HDMI or SDI cable, and connect a monitor to receiver unit by RX side HDMI
cable.
Connect power source to both units by power cables.
Power on both units and devices connecting to them.
After 10~20 seconds, LED1 on both units should be on if wireless connection
has been established successfully.
After a few seconds, the video capturing by the video source on the transmitter
side, should be playing on the monitor on the receiver side.
Note: If you want to see the video on PC, you should first install one software
named Tplayer on yout PC, then use Ethernet cable to connect Lan1
or Lan 2 in FPM-8416 . At the end , click the software and select adapter .
If one serial device is connected to transmitter side, another serial device is
connected to receiver side, and their voltage/data format is configured
according by section 4.3 Serial Data Format, they should be able to
communication with each other now.
3.2 Network Configurations
FPM-8416 units are working as wireless routers, the transmitter and receiver connects two
different network segments: 192.168.1.X and 192.168.2.X
IP Address of FPM-8416 units
Transmitter
Receiver
192.168.1.1
192.168.2.129
www.iwavecomms.com
６
IP configuration of devices connecting to FPM-8416
Transmitter side
Receiver Side
IP Address
192.168.1.X
192.168.2.X
gateway
192.168.1.1
192.168.2.129
mask
255.255.255.0
255.255.255.0
3.3 Setting up steps of Network Communication
Connect two antennas to transmitter unit by antenna-cables.
Connect two antennas to receiver unit by antenna-cables.
Configure the IP/gateway/mask of devices connecting to both units according
by 3.1.
Connect network devices to LAN ports of transmitter/receiver unit.
Connect power source to both units by power cables.
Power on both units and devices connecting to them.
After 10~20 seconds, LED1 on both units should be on if wireless connection
has been established successfully.
Now the devices on transmitter side should be able to communicate with
devices on receiver side.
If one serial device is connected to transmitter side, another serial device is
connected to receiver side, and their voltage/data format is configured
according by section 4.3 Serial Data Format, they should be able to
communication with each other now.
Note: FPM-8416 supports HDMI or SDI video transmitting and network communication
simultaneously. While when HDMI or SDI video is transmitting over wireless channel, there is
only 100kbps throughput left in the channel for LAN1+LAN2.
www.iwavecomms.com
７
4 Details and Notice
4.1 TTL Serial Cable
TTL Serial cable is for transmitting 3.3V TTL Serial signals
One header is 5P JST eGH header, the pin number shown in following picture, it shows
the header side with metal exposed
(note: Wire color is irrelevant)
Pin number
Signal
1
TXD
2
RXD
3
3.3V output, max 500mA (to power external device if necessary)
4
GND
5
Reserved
Another header consists of 3 Dupont plugs with different color wire:
Color
Signal
Red
TXD
Yellow
RXD
Black
GND
4.2 Ethernet Cable
One header is standard RJ45
Another header is 4P JST eZH header
www.iwavecomms.com
８
4.3 Serial Data Format
Default Baud Rate
115200
Data Bits
8
Parity
No
Stop bit
1
Voltage
3.3V
4.4 Notice
Before powering on units, make sure both SMA has connected to antennas.
Powering on a unit without antenna as load, the PAs inside it may subject to
damage.
Two antennas of one unit should keep certain distance.We commend 1 meter
or larger for transmitter side, 2 meters or larger for receiver side. If two
antennas don’t keep proper distance, the wireless signal may become weaker,
max range may become shorter.
Don’t dismantle or modify FPM-8416 units.
Tabla de contenidos
Otros manuales de Hardware de computadora de iWave
iWave
iWave FIM-2405 Manual de usuario
iWave
iWave iW-RainboW-G35D Manual de instalación
iWave
iWave iW-RainboW-G40M Manual de instalación
iWave
iWave i.MX6 Qseven PMIC SOM Manual de instalación
iWave
iWave FIM-2430 Manual de usuario
iWave
iWave FIM-1440 Manual de usuario
iWave
iWave FDM-6600 Manual de usuario
iWave
iWave FPS-8408 Manual de usuario
iWave
iWave i.MX 8M Mini Manual de usuario
iWave
iWave FMS-8480 Manual de usuario
iWave
iWave i.MX53 Manual de instalación
iWave
iWave iW-RainboW-G30D Manual de usuario
iWave
iWave iW-RainboW-G57M Manual de instalación
iWave
iWave FIP-2410 Manual de usuario
iWave
iWave iW-RainboW-G24M Arria10 SoC FPGA SOM Manual de usuario
iWave
iWave iW-RainboW-G17D Manual de usuario
iWave
iWave FD-6100 Manual de usuario
iWave
iWave FDM-615PTM Manual de usuario
iWave
iWave iW-RainboW-G25S Manual de usuario
iWave
iWave FIP-2420 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
