ITC TS-0690 Manual de usuario
Intelligently digital conference
system
User Manual
TS-0690
Before using the system, please read this manual first
NOTE:
This manual only as an instructions for user, not for service purposes. From the
date of issue, if the function or technical parameters change later, another supply
mentary instruction will be added, the details can be inquired to the manufacturers.
This manual is a product manufacturer Copyright, unauthorized and any entity
or individual shall not take part or all the contents as commercial purposes.
This manual used for intelligent digital conference system.
!
SAFETY OPERATIONAL GUIDANCE
In order to make sure the correct operation and safety using, please comply with
the following conditions when installation, operating and maintenance.
1) Make sure the connection of the ground wire is well enough when installation.
Do not use two-core plug. And make sure the input voltage of power supply is
as same as the one marked on the main controller.
2) Do not open the cover of the unit without permission especially the
high-voltage components marked with AC 100V to 240V, or there is risk of
shock.
3) Do not put the unit in extremely cold or hot place.
4) The unit will be heating when working. Please keep environment ventilation to
avoid overheating.
5) Please power off the unit in wet weather or not in use.
6) Please disconnect the AC power wiring from the AC power supply before the
below operations:
A. Remove or re-assembly any parts of the unit.
B. Disconnect or re-connect any plug of the unit or other connection
1Non professionals without permission, please do not attempt to open the
enclosure,do not repair, in order to avoid the accident or exacerbation of
equipment damage degree.
8) Don't take any corrosive chemical powders or liquids spilled in the equipment or
in the vicinity of.
1
1. Introduction of Digital Conference System
About ITC Digital Conference System
◆Digital conference system is another high-tech professional product after
multimedia central control products and audio-video matrix products. It
includes discussion units, simultaneous interpretation system, IR voice
distribution, remote telephone conference, voting and camera tracking etc.
◆Based on our complete system solution idea, it could be closely compatible
with both DCS (Digital conference System) and MCS (Multimedia Central
System) to become a complete intelligent conference system solution.
◆This user manual is applicable to Intelligent Digital Conference Controller,
Discussion Units, Camera Tracking System and Telephone Conference System.
2
2. Features
◆Supporting 6 video signals inputs: RCA, BNC, VGA, 3 lines of video signal
inputs.
◆Built-in Scaler, transferring VIDEO signal to VGA output, capable of being set
as 800x600，1024x768，1280x1024 DPI in the software.
◆Supporting TS and TH series conference controller at the same time and
compatible with three kinds of camera tracking controllers: TH-0580,
TH-9000M and TS-0690.
◆The tracking controller has a function of screen freeze, and the period of
screen freeze could be set by the software.
◆The ID number and preset position of the camera could be set by PC. Each
camera could be preset about 127+1 and with 6 cameras at max.
◆The control camera is supporting different Baud rates such as 9600，2400，
4800，19200, and different protocols such as Samsung. VISCA. Pelcd-D.
3
3. TS-0690 Auto Video Tracking Controller
Functions
1) Power—Power indicator.
2) Power switch.
1) Power input, supporting AC 100-240V input.
2) To the ground.
3) VIDEO INPUTS—connecting 6 camera video signal input.
4) VIDEO OUTPUTS—output RCA, BNC, VGA3 camera video signal.
5) CODE—protocol and Baud rate setting switch (not supporting the protocol
from other supplier at present).
6) CAMERA NET— using in high-speed camera RS485.
7) DATA—connecting with the conference controller named TH-0802M.
8) CONFERENCE SYSTEM—connecting with the conference controller
(TS-0604M).
9) CONTROL SYSTEM—connecting with the central controller (PC).
4
4. Technical Specifications
Model
Technical specifications
Auto Video Tracking Controller
Video
Gain 0 dB
Video Bandwidth
150MHz (-3dB),full-loading
0 -10MHz:≤+/- 0.1dB
0 -30MHz:≤+/- 0.5dB
multi-channel to single channel
cross talk -50dB @ 5 MHz, -45dB @ 10 MHz
Differential phase I/OS <1.28 degree，3.58MHz
Differential phase error 0.1%, 3.58-4.43MHz
Differential phase gain error 0.1degree, 3.58-4.43MHz
The max transmission delay 5nS(±1nS)
the switching speed 200 ns(longest time)
Signal type composite video signal
video input
interface 6 BNC female interface
minimum/maximum electric
level analog signal: 0.5V ～2.0V p-p
impedance 75 Ω
back wave loss -30dB@5MHz
genlock 0.3V-0.4Vp-p
The largest DC offset error 15mV
Video output
interface
1 BNC female interface and 1 RCA female
interface
minimum/maximum electric
level Analog signal: 0.5V ～2.0V p-p
Impedance 75 Ω
back wave loss -30dB@5MHz
DC offset ±5mV ±5mV at max
conversion type vertical interval
interface 15-pin HD female interface
minimum/maximum electric
level 2.0V p-p
Impedance 75 Ω
back wave loss <-40dB@5MHz
DC offset ±5mV ±5mV at max
sync signal
input/output type NTSC 3.58，NTSC4.43，PAL，SECAM;
Controlling types
5
Model
Technical specifications
Auto Video Tracking Controller
serial control interface 9-pin female type D RS-232 interface
Baud rate and protocol
Baud rate: 9600, data bit: 8 bits, stop bit: 1,
without parity check bit
specifications
power supply AC100-240V 50～60Hz(power switching)
temperature temperature of storage and operating:-20°～
+70°C
Dimension 485(L)x 245(W)x 45mm(H)
Weight About 1.5kg
5. Instruction of using PC software
5.1 Six video channels，Set up the conference platform
1) Open the PC software, set the serial, switching the video through PC software,
the display screen could be switched to different channel displays.
Notice: The address of video channel should be as same as the camera's.
5.2 Screen freeze period function
1) The screen freeze period could be set through PC software from 1-6 seconds.
The screen freeze period is beside the setting period when the camera is
rotating. It also has the function of protecting power losing.
5.3 Image resolution
1) Any of the three image resolutions could be selected by PC software and it
has the function of protecting power losing.
6
5.4 Getting the information of code switching
1) Turning the code switching on the rear panel of the unit, re-up electricity of
the unit, click "achieve" on the PC software to get the code switching protocol of
the camera tracking controller, Baud rate and the type of camera. Checking
whether the protocol, Baud rate and camera type are as same as the real setting
of the camera connection.
If only turning the first code, choosing VISCA protocol.
If only turning the second code, choosing SAMSUNG protocol.
If neither the first or second code is turned, choosing Pelcd D protocol.
If only turning the third code, choosing the Baud rate of the control camera at
2400.
If only turning the fourth code, choosing the Baud rate of the control camera at
4800.
If both the third and fourth codes are turned, choosing the Baud rate of the
control camera at 19200.
If neither the third or the fourth code is turned, choosing the Baud rate of the
control camera at 9600.
If the fifth code is turned, it is desk top camera; if not, it is wall mount camera.
5.5 Reset to Factory Defaults
Click "Reset to Factory Defaults", the screen freeze period of this is 1S, the DPI
is 1024*768, the camera channel number is the first one(it is valid when re-up
electricity).
5.6 Camera address setting
Camera Address ，Input the corresponding camera
address to control the cameras by the following keys.
7
5.7 The invoking, delete and setting of camera presetting
Choosing the camera protocol, input camera address and presetting position to
control the unit.
5.8 Setting the presetting position of the unit
1) Choosing the right protocol, camera address, presetting position, unit
address, adjusting the camera position via the up and down keys to the right
unit, then click "Setting" to finish the presetting bit of the unit. After setting all
the presetting bits accordingly, the camera will automatically point to speech
unit when opening the units.
5.8.1 Supporting three kinds of camera protocol
It could control the rotation direction of the camera and the presetting bits by
selecting the three kinds of different protocols in the PC software.
Tabla de contenidos
Otros manuales de Sistema de conferencias de ITC
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
