ipf electronic DW35312 Series Manual de usuario
manual pressure sensorspage 1
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!
Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
Manual
pressure sensors
DW35312x
DW36312x
page 2 manual pressure sensors
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!
Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
table of contents
Safety instructions page 3
Controls and indicating elements page 4
page 5
page 6
page 8
page 9
page 9
page 10
page 10
page 11
page 12
page 12
page 15
page 16
page 17
Description of the operating elements
Menu / overview
Operation modes of the switching outputs
Switch-point with release position
Switch-point with hysteresis
Window function with switch-point
Window function with hysteresis
Operating modes
Programming
List of parameters
Mounting and electrical connection
Initial operation / operation
Factory settings / Technical data
Dimensional drawings / list of articles
page 18
manual pressure sensors page 3
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!
Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
Safety instructions
Read the product description before installing the unit. Ensure that the product
is siutable for your application without any restric-tions.
Non-adherence to the operating instructions or technical data can lead to
personal injury and/or damage to property.
In all applications please check the compliance of the product materials (see
technical data) with the media to be measured.
Never use these articles in applications where the safety of a person depends
on their functionality.
page 4 manual pressure sensors
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!
Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
Controls and indicating elements
description function symbol
1 4-digit display displays the current system pressure
parameter, parameter values
265.4
2 LED red
S1
displays the switching state of output 1
lights, if the output is switched -
3 LED red
S2
displays the switching state of output 2
lights, if the output is switched -
4 programming button
Enter/ Set
selection of menu and parameters
setting and saving of parameters
Enter
Set
Enter
Set
5 arrow key
up
setting the parameter values
increasing the value
(fast, keep the button pressed)
6 arrow key
down
setting the parameter values
decreasing the value
(fast, keep the button pressed)
7 ESC finishing programming without saving
keyboard lock: press both the arrow keys at
the same time
ESCESC
manual pressure sensors page 5
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
265.4
265.4265.4
SP.2
Description of the operational controls
Display
4-digit LED display
Symbolic description:
shows the current system pressure (RUN-Mode), menu name, parameters
and parameter values.
blinking display in RUN-Mode: fault report (Error).
3 x blinking in PROGRAMM mode: saving current value after pressing
Enter/Set button.
The indication on the display depends on the programmed function.
If one of these functions is selected in the enhanced Menu, the indication
will be shown on the display.
Program button Enter/Set
Symbol:
Enter
Set
Enter
Set
Selection of menus and submenus as well as confirming and saving of parameter values.
Short pressing in the RUN-Mode →starting up the base menu.
Arrow keys
Symbol:
and
Increasing and decreasing the parameter values and scrolling of the menu.
Pressing the button continuous, the value increases or decreases in „fast-forward“ mode.
Pushing the button →the value changes step by step.
page 6 manual pressure sensors
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
ESC- button
Symbol:
ESCESC
Pressing both arrow keys + at the same time results in the ESC function.
With the ESC function you can step backwards inside the menu and parameters
without saving the settings.
In order to leave all menus and submenus please press the ESC-button again and again
until you are back in the RUN-mode.
Keyboard lock
If the device is in the RUN-Mode and you press the arrow keys + at the same
time for at least 5 seconds, the keyboard lock will be activated.
The display shows „sLOC“, blinking 3 times.
Now the adjusted settings can be read but not be changed.
For cancelling the Keyboard Lock please press both arrow keys + for at least 5
seconds again.
Menu / overview
1. level
manual pressure sensors page 7
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
2. level
page 8 manual pressure sensors
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!
Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
Operation modes of the switching outputs
notes:
•The following examples and descriptions of the switching output 1 (SP1) refer to the
switching function „normally open“ (no). If the switching output 1 is set „normally
closed“ (nc) the states are reversed.
•The minimum range between the switching outputs (SP.1 and rSP.1) is 1% of the
nominal pressure; stated by the system.
•The smallest adjustable hysteresis is 1% of the nominal pressure; stated by the sys-
tem.
•All examples are effective for output 2, if this output is defined as switching output
(SP-2) also.
manual pressure sensors page 9
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
switch-point with release position
Programmed parameters: SP.1:
250.0 bar
rP.1:
40.0 bar
An increasing pressure up to SP.1 (e.g. 250bar), switches the output according to the ad-
justed switching function (no or nc). This state remains also for higher pressure.
For decreasing pressure the switching state changes with the pressure value at rP.1 (e.g.
40bar). If SP.1 will be changed, rP.1 remains the same.
The minimum range between SP1 and rSP.1 is 1% of the maximum pressure.
Switch-point with hysteresis
Programmed parameters:
SP.1:
50.0 bar
HYS.1:
20.0 bar
An increasing pressure up to SP.1 (e.g. 50bar) switches the output according to the ad-
justed switching function (no or nc). This state remains also for higher pressure.
For decreasing pressure the switching state changes after passing the hysteresis (e.g.
20bar). If SP.1 will be changed, the hysteresis HYS1 remains the same, that is the release
position is (SP.1 – 20)bar.
pressure [bar]
switch-point
release position
switch-point
pressure [bar]
page 10 manual pressure sensors
ipf electronic gmbh
Kalver Str. 25 - 27
58515 Lüdenscheid - Germany
www.ipf-electronic.com Subject to alteration!
Tel +49 2351 9365-0
Fax +49 2351 9365-19 info@ipf-electronic.com
Window function with release position
Programmed parameters: SP.1:
250.0 bar
rP.1:
40.0 bar
Due to the window function, the monitoring of a defined pressure range is possible.
As soon as the pressure reaches the adjusted range between rP.1 (40bar) and SP.1
(250bar), the output switches according the chosen switching function (no or nc).
The switching state changes if the pressure leaves the adjusted pressure range.
The values for the switching point and the release point have to be defined separately.
If SP.1 changes, rP.1 will remain the same.
Window function with hysteresis
Programmed parameters: SP.1:
50.0 bar
HYS.1:
20.0 bar
If the pressure hits the adjusted window between (SP.1-HYS.1) and SP.1 (50bar), the
output switches according to the adjusted switching function (no or nc). The switching
function changes when leaving the window. If SP.1 changes, the hysteresis will not
change, e.g. the release position is (SP.1 – 20)bar.
pressure [bar]
switching pointrelaese position
pressure [bar]
switching point SP1
Este manual sirve para los siguientes modelos
12
Tabla de contenidos
Otros manuales de Accesorios de ipf electronic
ipf electronic
ipf electronic RO570900 Manual de usuario
ipf electronic
ipf electronic ON430570 Manual de usuario
ipf electronic
ipf electronic OTQ90170 Manual de usuario
ipf electronic
ipf electronic OT05E244 Manual de usuario
ipf electronic
ipf electronic PT230020 Manual de usuario
ipf electronic
ipf electronic OT059170 Manual de usuario
ipf electronic
ipf electronic OTR49175 Manual de usuario
ipf electronic
ipf electronic ON330571 Manual de usuario
ipf electronic
ipf electronic UT990934 Manual de usuario
ipf electronic
ipf electronic PT120320 Manual de usuario
ipf electronic
ipf electronic UT300027 Manual de usuario
ipf electronic
ipf electronic UT360321 Manual de usuario
ipf electronic
ipf electronic OT059176 Manual de usuario
ipf electronic
ipf electronic UT30C310 Manual de usuario
ipf electronic
ipf electronic OT330571 Manual de usuario
ipf electronic
ipf electronic DW34311 Series Manual de usuario
ipf electronic
ipf electronic UT129521 Manual de usuario
ipf electronic
ipf electronic PY740020 Manual de usuario
ipf electronic
ipf electronic OTR49174 Manual de usuario
ipf electronic
ipf electronic UT139073 Manual de usuario
