IPC PW-C25 Manual de usuario

Service Manual

Rev.1.0 January 2013

PW-C25 & PW-C25P

Models

1509P-M 230V 50Hz

I1509P-M 230V 50Hz

1813P-T 400V 50Hz

I1813P-T 400V 50Hz

I1310P4-M 230V 50Hz

Pag. 2

C25 / PW

C25P

outer layout

High pressure hose – spray gun – lance

Hose reel handle

Main switch 0-I

Chemical tap and regulator

Lance holder

Water inlet fitting

Water outlet fitting

Pressure adjust

Pump oil window

Pressure gauge

Hose reel rotation lock

Chemical tank

Lance holder

High pressure outlet

Foot lever

Refill cap

Pag. 3

C25 / PW

C25P inner

layout

Water outlet fitting

Water inlet fitting

Pressure gauge

Oil cap with air breath

By-pass valve

Total stop micro-switch

Pressure adjusting knob

Oil cap for handling and

transportation

High pressure pump

Oil level window

Electric motor starting

capacitor

Electric motor Electric enclosure

Chemical injector

Chemical tap and dose

Main switch

Standard accessories

set, that includes the

inlet water filter and

“garden” quick inlet

fitting.

Pag. 4

PW-C25 / PW-C25P

electric box components

layout

Electric box for wiring

the electric motor, the

starting capacitor, the

total stop switch and the

power cord.

Electric box for on – off

main switch

Pag. 5

Service Manual

INDEX

Topics

1. The machine doesn’t starts Page

1a No electrical connection 7

1b No electrical supply to the electric motor or

motor thermal sensor overload intervened or burnt fuses 7

1c The micro-switch of bypass valve not working

(only for machine with total stop system)

1d Contactor not working (on versions three phase or P4) 13

2. No water jet at the lance nozzle Page

2a Bad or missing water feeding connection 14

2b Inlet water filter clogged 14

2c Air intake from the water feeding circuit 15

2d Pump head valves ceased 15

2e High pressure nozzle clogged 16

3. No pressure to the lance Page

3a Defective water feeding connection 17

3b Inlet water filter clogged 17

3c Air intake from the water feeding circuit 18

3d Pump head valves ceased or worn 18

3e Lance nozzle set in low pressure mode (detergent mode) 19

3f High pressure nozzle worn or deformed 19

3g Pressure adjusting valve setting at minimum position 20

3h Seat of pressure adjusting valve damaged 20

3i Pump gaskets worn or water leaks from the pump head 23

Ip Cleaning S.p.A.

Viale Treviso, 63 – 30026 Summaga di Portogruaro – VENICE – ITALY

Tel. +39 0421 205511 (r.a.) – Fax +39 0421 204227

Internet address: www.ipcportotecnica.com

e-mail address: infoipcportotecni[email protected]

Pag. 6

4. Poor detergent delivery Page

4a Detergent tap closed/off or clogged 24

4b Empty detergent tank or nozzle not set in detergent mode 25

4c The check valve of the detergent circuit is sticky or clogged 25

4d High pressure outlet pipes clogged or too much extended (over 20 m).

Wear and tear of the detergent nozzle 26

4e Pressure regulator is not set at maximum position 26

5. Oil and water emulsion phenomena to the high pressure pump oil Page

5a Extremely high environment humidity percentage 27

5b High pressure pump gaskets worn 28

5c High pressure pump pistons damaged 28

6. The total stop system doesn’t intervenes

(only for machines having this option) Page

6a Water leaks from the high pressure outlet circuit 29

6b Micro-switch of the bypass valve, or contactor, not functioning 29

Pag. 7

1. The machine doesn’t starts

1) TROUBLE: Rotating the main switch “0 – I” (A) the high pressure cleaner doesn’t starts or

starts, but suddenly stops after a while.

CAUSES: 1a No electrical connection

1b No electrical supply to the electric motor or motor thermal sensor overload

intervened or burnt fuses

1c The micro-switch of bypass valve not working

(only for machine with total stop system)

1d Contactor not working (on versions three phase or P4)

REMEDIES:

1a Check the power supply voltage using a “multimeter”.

The machine power supply characteristics are indicated on the machine data plate placed on the

rear side of its chassis.

For single-phase models, the allowed voltage tolerance is +/- 5%.

For three-phase models, the allowed voltage tolerance is +/- 10%.

If the voltage is over or lower than the above mentioned tolerance, the machine electric

components may become damaged.

Pay maximum attention while checking electric component: danger of electric shocks.

1b Pay maximum attention: danger of electric shocks.

Disconnect the machine from the power supply before opening the electric enclosures, hence:

(

)

Machine data plate

Pag. 8

- check using a multimeter, the conductivity of the main switch contacts, rotate the switch knob to

position “I” and in case of problems, replace the switch with a new component.

To open the electric enclosures, proceed as following described:

Opening:

3. Remove the main switch knob

Remove the machine cover

5. Check the main switch contacts continuity using a

multimeter, if damaged replace it.

2. Remove the handle cover

4. O

pen the electric box cover

Pag. 9

- If the thermal sensor of the electric motor is intervened, the electric motor is disconnected and

the machine cannot work.

The thermal sensor, intervenes when the motor winding temperature is over 155°C and in order

to cool it down and allows its automatic reset, are required some minutes with the electric motor

off.

The thermal sensor is built-in into the motor winding of single phase models, while is wired into

the electric box for three-phase models or for P4 models.

The thermal sensor is a protection against overload and needed to prevent burning of the motor

windings, but has a limited life in term of number of interventions and if the machine has been

used continually under overloaded, the thermal sensor can become damaged and loose the

capacity to self reset, hence not allowing the motor to restart when decreases the winding

temperature.

In order to restore a damaged thermal sensor, is needed to replace the complete electric motor

stator.

- If the fuses of the socket or to the plug are burnt, the machine is not power supplied; replace the

fuses and check if their amperage is enough for the machine Amperage characteristics that are

readable on its data plate.

Take into consideration that a low voltage supply can cause difficulties to the motor starting and

as a consequence can makes that fuses burn.

We recommend to check the machine amperage using a clamp meter in order to be sure that the

machine working at the maximum pressure is not absorbing more Ampere than what indicated on

its data plate.

Measured

Amperage

should be less or

equal than Amperage wrote to the machine

data plate.

Check the Amperage with a A clamp meter

after switching on the machine and checking

that the machine is correctly power supplied

by the fuses.

Pag. 10

Electric diagrams

Single phase by-pass Single phase total stop

Otros manuales para PW-C25

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hidrolavadora de IPC

IPC

IPC PW-C23P Manual de usuario

IPC

IPC PW-H31 1708 NE 1x230v Manual de usuario

IPC

IPC PW-H35 Runner-H Manual de usuario

IPC

IPC HPS 1012M Manual de usuario

IPC

IPC BENZ-C H 1811Pi Manual de usuario

IPC

IPC ML.Compact 1910M Manual de usuario

IPC

IPC Royal Press Manual de usuario

IPC

IPC 1813P-T Manual de usuario

IPC

IPC HPS-HD-H 1012M Manual de usuario

IPC

IPC Sibi Max Manual de usuario

IPC

IPC PW-C04 Manual de usuario

IPC

IPC PW-H25 Universe Manual de usuario

IPC

IPC PW-C25 Manual de usuario

IPC

IPC PW-C08 Manual de usuario

IPC

IPC 146085 Manual de usuario

IPC

IPC 146075 Manual de usuario

IPC

IPC PW-C50 Manual de usuario

IPC

IPC D 1814P4 T Manual de usuario

IPC

IPC PW-C23 Manual de usuario

IPC

IPC IWD-H Series Manual de usuario

IPC

IPC N. Royal Jet Manual de usuario

IPC

IPC Galax-H PW-H50 Series Manual de usuario

IPC

IPC Portotecnica ML.Compact 1910M Manual de usuario

IPC

IPC PW-H10 Manual de usuario

Manuales populares de Hidrolavadora de otras marcas

Shark

Shark RG-232637 Manual de usuario

Shakti Technology

Shakti Technology S3 Manual de usuario

Kärcher

Kärcher K 4 Pure Manual de usuario

Porter-Cable

Porter-Cable D25806-025-2 Manual de usuario

REM POWER

REM POWER HDEm 662 Manual de usuario

Landa

Landa HS-3000 Manual de usuario

Craftsman

Craftsman 580.752270 Manual de usuario

HIKOKI

HIKOKI AW 100 Manual de usuario

Delco

Delco DC 1302 Manual de usuario

Kärcher

Kärcher K 3 Full Control Manual de usuario

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manual de usuario

ARKSEN

ARKSEN 014-HG-14141-HR Manual de usuario

Black & Decker

Black & Decker PW1700SPX Manual de usuario

Kärcher

Kärcher 595 - SPARE Guía

Kranzle

Kranzle B 10 200 Manual de usuario

Stihl

Stihl RE 90 Manual de usuario

Husky

Husky HU80911 Manual de usuario

PowR-Quip

PowR-Quip PQ-2600 Manual de usuario