IP-COM W40AP Manual de usuario
Quick Installation Guide
WirelessN300CeilingAccessPoint
Model:W40AP
Package Contents
Access point * 1
Bracket * 1
Power adapter * 1
Mounting accessory (including sleeve anchors and screws) * 1
Quick installation guide * 1
If any item is incorrect, missing, or damaged, please keep the original package and contact the local reseller or distributor
immediately.
For more product or function details, please go to www.ip-com.com.cn to download the user guide.
1. Know Your AP
LED
indicator
StatusDescription
SYS
Solid onThe system is starting.
If the indicator is still solid on after the AP finishes startup,
it indicates that the system is faulty.
BlinkingThe AP is working properly.
OffTheAP is powered off or the LED indicator is disabled.
Port / ButtonDescription
LAN
It is a 10/100 Mbps auto-negotiation port used to transmit data or supply PoE
power for the AP using Ethernet cable. PoE devices complied with IEEE 802.3af
or IEEE 802.3at standard can supply power to the AP.
PWR It is a DC power jack used to connect to the included power adapter.
RESET
It is used to reset theAP.
Method to reset: When the SYS indicator blinks, hold the RESET button down for
about 8 seconds. The AP is reset successfully when the SYS indicator gets solid
on.
2. Install the AP
Tip:
You may need a rubber hammer, a marker, a hammer drill, a drill bit, a screwdriver, and a ladder for the installation. Please
prepare them yourself.
❶ Position the bracket onto the celling and mark screw holes on the celling with the marker.
❷ Drill holes in the marked positions using hammer drill.
❸ Knock the sleeve anchors into the holes using the rubber hammer.
❹ Align the screw holes with the holes in the ceiling, and then use the included screws to fix the bracket.
❺ Connect an Ethernet cable (CAT5 or better) to the LAN port of the AP. If you choose to power on the AP by DC supply,
connect the PWR port of the AP using the power adapter included in the package.
❻ Insert the hooks of the AP into the slots of the bracket, and slide the AP to one side to make sure that the AP is fixed
well in the bracket.
3.Set Up Your WiFi Network
Note: PoE supply is used as an example in all the setup instructions below.
Scenario 1: Set up WiFi network without a management device for IP-COM AP
Tip:
Connect one AP to your PoE switch first. After configuring the AP, connect another AP, perform ❸,❹, and
on it, and so on.
❶ Connect devices
Connect your AP to a PoE port of the PoE switch using an Ethernet cable. Refer to the following figure for detailed
connection.
After finishing connection, ensure that the AP’s LED indicator blinks and the lower-right network icon on your computer
is not displayed .
LAN WAN
Uplink
❷Configure the IP address of your computer (Example: Win7)
Right-click the network icon on the lower-right corner of your computer. Click Open Network and Sharing Center, Local
Area Connection, and then Properties. Double-click Internet Protocol Version 4 (TCP/IPv4), select Use the following IP
address, set IP address to 192.168.0.x(x: 2 to 253. The IP address in this example is 192.168.0.10) and Subnet mask to
255.255.255.0, and click OK.
❸Log in to the web UI of the AP
Start a web browser on your computer, and enter the AP’s management IP address (192.168.0.254) in the address bar,
and press Enter. Then enter the user name and password (default: admin/admin) of the AP, and click Login.
Tip: If you cannot log in to the web UI of the AP, refer to Q1 in FAQ.
❹Set WiFi name and WiFi password for the AP
Click Quick Setup, then configure SSID (WiFi name), Security Mode (WPA2-PSK is recommended), Key, and click
Save.
Change the IP address of the APClick Network, LAN Setup. Change the IP address of the AP to 192.168.0.x(x: 2 to
253), and ensure that the new IP address has not been used in this network, then click Save. For example, you can
set the new IP address of the firstAP to 192.168.0.201, and the new IP address of the second AP to 192.168.0.202.
Wait a moment for the settings to take effect. Now you can access the internet by connecting your wireless devices to
the AP’s WiFi network.
WiFi name: The SSID you set in step .
WiFi password: The key you set in step .
Scenario 2: Set up WiFi network with an IP-COM AP Controller
❶ Connect devices
Use Ethernet cables to connect APs to the PoE ports of the switch, and your computer to the IP-COM AP Controller
(AC). Refer to the following figure for detailed connection.
❷ Configure APs
In order to configure your APs, start a web browser on your computer and log in to the web UI of the AC. Refer to your
AC’s user guide for detailed configuration instructions.
IP‐COMAPController
UPlink LAN WAN
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de IP-COM
IP-COM
IP-COM W45AP Manual de usuario
IP-COM
IP-COM AP355 Manual de usuario
IP-COM
IP-COM W30AP Manual de usuario
IP-COM
IP-COM AP255_US Manual de usuario
IP-COM
IP-COM AP615 Manual de usuario
IP-COM
IP-COM AP375 Manual de usuario
IP-COM
IP-COM W45AP Manual de usuario
IP-COM
IP-COM W185AP Manual de usuario
IP-COM
IP-COM W300AP Manual de usuario
IP-COM
IP-COM Pro-6-IW Manual de usuario
Manuales populares de Punto de acceso inalámbrico de otras marcas
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario
Ubiquiti
Ubiquiti NanoStation NSM2 Manual de usuario
Cisco
Cisco Aironet 1550 Series Manual de usuario
Aruba
Aruba IAP-335 Manual de usuario
Advantek Networks
Advantek Networks AWN-AP-54MR Manual de usuario
Buffalo
Buffalo AirStation WLA-L11G Manual de usuario
