IOptron CEM26 Manual de usuario

Instruction on Polar Scope Replacement of a CEM26/GEM28 Mount

Toll needed: a set of metric Allen wrench

DO NOT OVER TIGHTEN THE SET SCREW!!!

To Remove/Replace/Rotate a CEM26/GEM28 iPolar:

For GEM28

1. Unthread the red RA rear cover

2. Release two set screws on RA axle.

3. Pull out the iPolar

4. Set the mount in Zero Position and insert a New iPolar

5. Check the iPolar orientation to make sure ALT adjustment will result image vertical movement.

For CEM26

1. Release the screws from side

2. Release the other screw from the bottom

3. Pull out the iPoler

4. Set the mount in Zero Position and insert a New iPolar.

5. Check the iPolar orientation to make sure ALT adjustment will result image vertical movement.

To Install an AccuAlignTM Optical Polar Scope:

The RA axis locking wrench will not be able to be used due to the length of optical polar scope.

The LED brightness is not adjustable. You’ll need to block part of the LED if you would like a dim illumination.

1. Set the mount at Zero Position

2. Insert the optical polar scope. Set any one of major marks on top to assume the 12 o’clock position.

3. Tighten the set screws

4. Thread in the polar scope LED. Plug the 3mm DC plug into the LED and 5.5mm plug into DC 12V OUT socket on

main board.

5. Turn on the mount power to check the LED and polar scope.

Major mark

Polar Scope Alignment

There are three Reticle Adjustment Screws on the side of the Polar scope, as shown in the following photo.

(1) Aim the polar scope to a distant object, such as a flag top or building corner. Adjust the object lens to focus the polar

scope to the object. Adjust the eyepiece to see the dial clearly. Center the object in polar scope by adjusting mount

altitude and azimuth adjustment screws.

(2)Bring the object half the distance to the center by adjusting the reticle adjustment screws. Loose one screw first,

then tighten the other screw(s). Only loose/tighten one screw at a time and very small amount of turn each time to

avoid the reticle totally lost its position. It may take a few minutes to familiarize yourself with the screws that move the

polar scope in the appropriate direction. PLEASE do not over tighten the setting screws. The reticle is made from a

glass.

(3) Rotate the mount 180 degree to bring the mount back to the left side. If you are lucky enough, the object will stay in

center of the polar scope. Otherwise, repeat Step 1 to further move the object to the center. After few times, the object

will stay in center when the mount is flipped from right to left.

Rotate

Center the object

Bring the object

half the distance

to the center

Rotate

Center the object

Bring the object

half the distance

to the center

Reticle Adj. Screws

Objective Lens

Lock Ring

Otros manuales para CEM26

Este manual sirve para los siguientes modelos

Otros manuales de Rack y soporte de iOptron

iOptron

iOptron CEM70 Manual de usuario

iOptron

iOptron CEM40G Manual de usuario

iOptron

iOptron HEM27 Manual de usuario

iOptron

iOptron CEM120 Manual de usuario

iOptron

iOptron CEM25P Manual de usuario

iOptron

iOptron 7100P Manual de usuario

iOptron

iOptron C70A Series Manual de usuario

iOptron

iOptron CEM40EC Manual de usuario

iOptron

iOptron CEM25P Manual de usuario

iOptron

iOptron iEQ30 Pro 3000E Manual de usuario

iOptron

iOptron CEM40 Manual de usuario

iOptron

iOptron CEM120 7300 Manual de usuario

iOptron

iOptron GEM45EC Manual de usuario

iOptron

iOptron GEM28 Manual de usuario

iOptron

iOptron iEQ30 Pro 3000E Manual de usuario

iOptron

iOptron SmartStar CubePro GOTO AltAz Manual de usuario

iOptron

iOptron CEM40 Manual de usuario

iOptron

iOptron HAZ31 Manual de usuario

iOptron

iOptron HEM27 Manual de usuario

iOptron

iOptron SmartStar iEQ45 Manual de usuario

iOptron

iOptron HAE29 Manual de usuario

iOptron

iOptron MiniTower GOTO Manual de usuario

iOptron

iOptron CEM26 Manual de usuario

iOptron

iOptron CEM60 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario