intertel EncoreCX Manual de usuario
EncoreCX
Internet Module Manual
1
Table of Contents
TABLE OF CONTENTS .......................................................................................................................1
INTRODUCTION ..................................................................................................................................2
FEATURES .............................................................................................................................................2
CONNECTING TO THE ENCORECX PROGRAMMING AND MAINTENANCE
SOFTWARE ...........................................................................................................................................3
RESETTING THE INTERNET MODULE.........................................................................................4
INSTALLATION WIZARD..................................................................................................................4
PC SETTINGS........................................................................................................................................6
USING THE INTERNET ......................................................................................................................6
LOCAL AREA NETWORK .................................................................................................................6
WIDE AREA NETWORK ....................................................................................................................6
DSL ......................................................................................................................................................7
BROADBAND .........................................................................................................................................7
INDICATORS ........................................................................................................................................7
DSL/BROADBAND PROFILE.............................................................................................................8
TIMEBANDS........................................................................................................................................10
DHCP SERVER....................................................................................................................................11
FIREWALL ..........................................................................................................................................13
FILTERS...............................................................................................................................................14
OUTGOING TRAFFIC FILTERS ..............................................................................................................14
INCOMING TRAFFIC FILTERS ...............................................................................................................15
STATISTICS ........................................................................................................................................17
LAN STATISTICS.................................................................................................................................17
ICMP STATISTICS ...............................................................................................................................19
SPECIFICATIONS ..............................................................................................................................21
LAN....................................................................................................................................................21
DSL ....................................................................................................................................................21
PROTOCOLS .........................................................................................................................................21
AUTHENTICATION ...............................................................................................................................21
DHCP .................................................................................................................................................21
ROUTING .............................................................................................................................................21
FIREWALL ...........................................................................................................................................21
ACCESS CONTROL................................................................................................................................21
MANAGEMENT ....................................................................................................................................21
EncoreCX
Internet Module Manual
2
Introduction
The Internet module is an EncoreCX system module that provides multi-user high-speed Internet
access using a Digital Subscriber Line (DSL) or Broadband. It also provides a Local Area Network
that allows users to network PCs and share printers and other resources within the office. It is easy to
install and manage using the installation wizard and management system. It can be installed during
the initial installation phase or added later.
Features
The Internet module has the following features:
·Installation wizard for easy setup
·Multi-user Internet access
·Local Area Networking
·DSL
·Broadband
·Firewall
·PC-based management
·External indicators
EncoreCX
Internet Module Manual
3
Connecting to the EncoreCX Programming and
Maintenance Software
·Select Connect on main screen. The following screen is displayed.
·Select Connect on pop-up screen.
·Select Internet Module. The following screen is displayed.
·Installation Wizard takes you to the Installation Wizard screen.
EncoreCX
Internet Module Manual
4
·Internet Module Configuration takes you to the Configuration screen.
·Get Configuration receives all settings and updates the corresponding fields in the management
system.
·Set Configuration sends all management system settings to the Internet Module.
·Restore Factory Defaults restores all settings to the original factory settings.
·Back takes you back to the previous screen.
For some configuration changes to take effect, a warm reset must be performed on the Internet module.
A prompt will appear on the EncoreCX Programming and Maintenance software screen requesting a
reset.
Resetting the Internet Module
The Internet module must be reset for some configuration changes to take effect. It can be reset via
the Programming and Maintenance software or by using the RESET button on the Internet Module
MDF. For reset via the Programming and Maintenance software, go to the main system screen and
select Diagnostics \ System Resets \ Internet Module \ Warm Reset.
Installation Wizard
The installation wizard allows you to quickly and easily set up an Internet connection.
Before you use the wizard, you must have the following information on hand.
·Will DSL or Broadband be used to access the ISP?
·If DSL is to be used, get the following information. This will be provided by your ISP.
- Username
- Password
- Which of the following protocols are used by the DSL modem ?
·PPPoE (Point-to-Point Protocol over Ethernet)
·Dynamic IP address assignment
·Static IP address assignment
If static IP addressing is used, skip the DSL Wizard and proceed to the DSL Profile.
·If Broadband is to be used, get the following information. This will be provided by your ISP.
- Username
- Password
- Which of the following protocols are used by the Cable modem ?
·PPPoE
·Dynamic IP address assignment
·Static IP address assignment
If static IP addressing is used, skip the Broadband Wizard and proceed to the Broadband
Profile.
EncoreCX
Internet Module Manual
5
The following procedure is now used to set up Internet access.
·Select Installation Wizard on the main screen. The following screen is displayed.
·Select DSL/Broadband. The following screen is displayed.
·Enter the Username. This will be provided by the ISP.
·Enter the Password. This will be provided by the ISP.
·Select either PPPoE or IP.
Note: If static IP addressing is used, skip the ADSL Wizard and proceed to the ADSL Profile.
·Click on the radio button - Enabled.
·Click Send.
The Internet module is now set up to access the Internet using DSL or Broadband.
EncoreCX
Internet Module Manual
6
PC Settings
Each PC used to browse the Internet must be configured to obtain an IP address automatically.
·Right click Network Neighborhood.
·Left click Properties.
·Select Protocols tab.
·Scroll through protocols listed and highlight TCP/IP Protocol and click the properties tab.
·Click radio button Obtain an IP address from a DHCP server.
·Click OK.
The PC is now set up to automatically obtain an IP address from the DHCP server in the Internet
module.
Internet Explorer must also be configured as follows.
·Select Tools on the menu bar.
·Select Internet Options on drop-down menu.
·Click Connections tab.
·Click LAN Settings.
·Ensure that Use a proxy Server box is not checked.
Using the Internet
Launching Internet Explorer on any PC connected to the LAN will automatically connect the user to
the Internet.
Local Area Network
The Internet module has a LAN (Local Area Network) which allows multiple PCs to connect to the
Internet. It also allows users to network PCs and share printers and other resources.
The Internet module has four 10/100 switched Ethernet ports for connecting PCs or other devices. If
more than four LAN devices are to be connected, an external Ethernet hub or hubs can be connected to
any or all of the ports to expand the LAN. The Internet module can accommodate up to a total of 100
LAN devices.
The RJ-45 connectors for these ports are located on the Internet module's Main Distribution Frame
(MDF) and are used to connect PCs or other LAN devices to the Internet module. Each port is set for
auto-configuration and auto-sensing to automatically adapt to network card settings in the PC or other
device that is connected to it. Also, each port can automatically adapt itself to a standard or crossover
cable.
Wide Area Network
The Internet module can use ADSL or Broadband to access the Internet.
EncoreCX
Internet Module Manual
7
DSL
DSL provides "always on" service, meaning the Internet module is permanently connected to the
Internet using a standard telephone line. The telephone line is terminated at the user end by a splitter
that provides a normal telephone connection as well as a high-speed data connection.
The Internet module is factory fitted with a 10 Base-T port for connecting to an external DSL modem.
A RJ-45 connector is provided on the Internet module backplane. The service provider installs the line,
the splitter and the DSL modem.
Broadband
Broadband provides "always on" service, meaning the Internet module is permanently connected to the
Internet using a cable modem.
The Internet module is factory fitted with a 10 Base-T port for connecting to an external cable modem.
A RJ-45 connector is provided on the Internet module backplane for connecting to the modem.
Indicators
The Internet module has six Light Emitting Diodes (LEDs) on the front of the Internet Module to
indicate the following:
·Active Flashing indicates normal operation
·WAN Flashing indicates traffic on 10 Base-T port
·LAN 1 Indicates activity on LAN port 1
·LAN 2 Indicates activity on LAN port 2
·LAN 3 Indicates activity on LAN port 3
·LAN 4 Indicates activity on LAN port 4
EncoreCX
Internet Module Manual
8
DSL/Broadband Profile
While the installation wizard provides a simple method of setting up the Internet module using the
minimum number of settings, the profile settings provide the user with the ability to assign static IP
addressing and access to Timebands to control Internet access.
The following procedure is used to set up the DSL/Broadband profile.
·Select Internet Module Configuration on the main screen. The following screen is displayed
·Select WAN on the Internet Module Configuration screen. The following screen is displayed
EncoreCX
Internet Module Manual
9
·Select DSL/Broadband Profile on the WAN Setup screen. The following screen is displayed.
·Enter the Username assigned by the ISP to allow access to the Internet. The username can be up
to 60 alphanumeric characters long.
·Enter the Password assigned by the ISP to allow access to the Internet. The password can be up to
20 alphanumeric characters long.
·Selecting aProtocol.
Select PPPoE or IP depending on how the ADSL service is delivered. This information will
be provided by your ISP.
·If using PPPoE, select PPPoE and proceed to the next step (NAT Enabled).
·If IP addresses are dynamically assigned by the ISP, select IP and proceed to the next step
(NAT Enabled).
·If IP addresses are to be statically defined, select IP and enter the relevant IP addresses in
the following fields:
Default Gateway IP address
WAN Net Mask
WAN IP address
Primary DNS Server
Secondary DNS Server
·NAT Enabled - this box is checked by default. This allows all PCs connected to the LAN to
concurrently access the Internet.
·Profile Enabled - this enables the profile.
·Click Save.
·Click Send.
·Timebands takes you into the Timebands menu, which allows you to restrict Internet access
during certain times of the day. The default setting is that no restrictions are applied. See the
section on Timebands.
The Internet module is now set up for Internet access using DSL.
Otros manuales para EncoreCX
2
Tabla de contenidos
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
