Intermec MicroBar NX Manual de usuario
MB/NX/IG/00/E/961031
MicroBar NX
Installation Guide
Preliminary Edition
October 1996
MB/NX/IG/00/E/961031
Notice
The MicroBar NX products described in this manual comply with CE directives for electromagnetic
emission levels and electrical immunity.
The information contained in this manual is for informational purposes only and is subject to
change without notice. No part of this manual may be copied or reproduced in any manner without
the prior written permission of United Barcode Industries.
MicroBar products are covered by patents issued or pending in the USA and other countries.
MicroBar is a trademark of United Barcode Industries.
MicroBar NX configuration codes are compatible with other new-generation UBI
products.
MicroBar NX configuration codes are not compatible with the MicroBar LS/PS.
MB/NX/CE/10/E/970210 iii
Scanner Technology Center
DECLARATION OF CONFORMITY
We,
UBI Scanner Technology Center
Immeuble Le Naurouze, Rue Carmin
Voie No.3, Innopole - BP 187
31676 Labège Cedex
France
declare under our sole responsibility1that the product(s)
MicroBar NX
to which this declaration relates
is (are) in conformity with the following standards:
Emission: EN 50081-1 (1992)
EN 55022 (1987) Class B
Immunity: EN 50082-1 (1992)
IEC 801-2 (1984 -91) 8kV in the air
IEC 801-3 (1984) 3 V/m
IEC 801-4 (1988) 1kV
Low voltage: EN 60950 (1993)
following the provisions of Directives
89/336/EEC
73/23/EEC
Toulouse 30/11/1996
...................................................................
Sven Skarendahl
President
1UBI assumes no responsibility as regards fulfilling the CE Directive if the product(s) is (are)
handled, modified or installed in other manners than those described in UBI’s manuals.
UBI Scanner Technology Center
Immeuble Le Naurouze, Rue Carmin
Voie No.3, Innopole - BP 187, 31676 Labège Cedex, France
Tel: +33 (0)5 61 39 98 58
•
Fax: +33 (0)5 61 39 20 00
iv MB/NX/CE/10/E/970210
MB/NX/IG/00/E/961031 v
What you are going to do . . .
This Installation Guide tells you how to install and set up your MicroBar NX to operate
successfully in most working situations.
The present guide does not cover all the configuration capabilities of your MicroBar NX. The
full set of configuration options is provided in the
MicroBar NX Reference Manual
.
Step by step how to install and set up your MicroBar NX
1 Check you have everything you need ..........................................................1-1
2 Switch off the host system and connect up the MicroBar NX ....................... 2-1
3 Connect the data input devices to the MicroBar NX.....................................3-1
4 Switch on the host system............................................................................4-1
5 Enter the interface number for your host system.......................................... 5-1
6 Set up the output transmission parameters..................................................6-1
7 Set up the data input parameters .................................................................7-1
Additional information is provided in the appendix
A Symbology parameters for barcode readers ................................................A-1
B Laser scanner parameters ...........................................................................B-1
C Magstripe parameters...................................................................................C-1
D RS-232 input device data transmission parameters.....................................D-1
E Additional operating parameters ..................................................................E-1
F If you have a problem . . ..............................................................................F-1
G Test codes................................................................................................... G-1
What you are going to do . . .
vi MB/NX/IG/00/E/961031
MB/NX/IG/00/E/961031 1-1
1 Check you have everything you need
Checklist of items for your installation
all systems MicroBar NX
the right cable for your host system
this
MicroBar NX Installation Guide
options UBI pen barcode reader
dual pen adaptor
MicroBar NX Reference Manual
MicroBar NX
decoder and interface unit used to connect one or more data input
devices:
• pen barcode readers
• laser/CCD barcode readers in wand/laser emulation
• undecoded magstripe readers
• RS-232 input devices—electronic scales, barcode readers,
magstripe readers, . . .
to a data processing host system—keyboard emulation for PCs and
terminals, RS-232 communication, . . .
external power supply
5V mains power supply adapter—necessary if the host system does
not provide enough electrical power to drive the MicroBar NX
1. Check you have everything you need
MB/NX/IG/00/E/9610311-2
MB/NX/IG/00/E/961031 2-1
2 Switch off the host system and
connect up the MicroBar NX
Host interfaces
Keyboard wedge—All except Wyse, DEC 220 / 320 / 420...........................2-2
Keyboard wedge—Wyse, DEC 220 / 320 / 420 ........................................... 2-3
RS-232 C / TTL ............................................................................................2-4
Dual RS-232 C .............................................................................................2-5
keyboard wedge
MicroBar NX connected between a keyboard and the host system—
data from the MicroBar NX is transmitted in keyboard emulation mode
to provide instant software compatibility (external power supply usually
required)
dual RS-232 C
MicroBar NX connected between two systems communicating through
an RS-232 link (external power supply usually required)
2. Switch off the host system and connect up the MicroBar NX
MB/NX/IG/00/E/9610312-2
Keyboard wedge—All except Wyse, DEC 220 / 320 / 420
• undecoded pen
• wand emulation device
• 5V power supply
(if required)
host computer
keyboard input
connector
Ø
input device
5V power supply
(if required)
31
2
4
1. Switch off the host system.
2. Disconnect the keyboard from the host computer.
3. Use the appropriate keyboard wedge cables to connect the MicroBar
NX between the keyboard and the host computer.
4. If your system requires an external power supply, connect the power
supply (jack or modular plug) to the MicroBar NX.
MDo not switch on the host computer or plug the external power supply into the
mains socket.
Otros manuales para MicroBar NX
1
Tabla de contenidos
Otros manuales de Escáner de Intermec
Intermec
Intermec SG10T Manual de usuario
Intermec
Intermec MaxiScan 3100 Manual de usuario
Intermec
Intermec IV7 Manual de usuario
Intermec
Intermec IF30 Manual
Intermec
Intermec MaxiScan 2500 Manual de usuario
Intermec
Intermec Sabre 1551C Manual de usuario
Intermec
Intermec MaxiScan 3300 Manual de usuario
Intermec
Intermec SG20T Manual de usuario
Intermec
Intermec Sabre 1514 Manual de usuario
Intermec
Intermec SR61T Manual de usuario
Intermec
Intermec SF51 Manual de usuario
Intermec
Intermec Sabre 1551 Manual de usuario
Intermec
Intermec Sabre 1517 Manual
Intermec
Intermec MicroBar NX Manual de usuario
Intermec
Intermec MaxiScan 2210 Manual de usuario
Intermec
Intermec Sabre 1514 Manual
Intermec
Intermec Sabre 1551 Manual
Intermec
Intermec Trakker Antares 2420 Manual de usuario
Intermec
Intermec ScanPlus 1800ST Manual de usuario
Intermec
Intermec ScanImage 1470 Manual de usuario
