Intermec Trakker Antares 2475 Manual de usuario
Trakker Antares®
2475 Vehicle-Mount
Terminal
Installation
Instructions
Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203-9280
U.S. service and technical support: 1-800-755-5505
U.S. media supplies ordering information: 1-800-227-9947
Canadian service and technical support: 1-800-668-7043
Canadian media supplies ordering information: 1-800-268-6936
Outside U.S.A. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for the purpose of allowing customers to
operate and/or service Intermec manufactured equipment and is not to be released, reproduced, or used for any
other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
2002 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, INCA (under license), MobileLAN, JANUS, IRL, Trakker Antares,
EZBuilder, TE 2000, Data Collection Browser, dcBrowser, Universal Access Point, UAP, Duratherm,
EasyCoder, Precision Print, PrintSet, Virtual Wedge, and CrossBar are either trademarks or registered
trademarks of Intermec.
Throughout this manual, trademarked names may be used. Rather than put a trademark (or ) symbol in
every occurrence of a trademarked name, we state that we are using the names only in an editorial fashion, and
to the benefit of the trademark owner, with no intention of infringement.
There are U.S. and foreign patents pending.
Contents
iii
Contents
Preparing to Install the Terminal 5
Guidelines for Mounting the Terminal 5
Required Tools and Materials 6
Installing the Terminal and Connecting Devices 6
Attaching the Antenna 7
Installing the Terminal 7
Using the Rail Mount 10
Installing and Connecting the DC Power Supply 11
Connecting the External Power Supply 13
Attaching a Scanner 14
Connecting to Serial Devices 15
Charging the Backup Battery 16
Blank page
Trakker Antares 2475 Vehicle-Mount Terminal Installation Instructions
5
Preparing to Install the Terminal
The Trakker Antares®2475 vehicle-mount terminal is designed to be mounted on a
vertical or horizontal surface on a vehicle such as a forklift truck. You can also use the
rail mount accessory to mount the terminal to a rail on the vehicle. You use a DC power
supply that is connected to the vehicle’s battery to power the 2475.
You can also mount the 2475 in an office location to program, develop, and test
applications. You use an external power supply and adapter cable to power the 2475.
Make sure you have the necessary equipment to install the 2475 and connect it to your
network. You need the following equipment that ships with the terminal:
•2475 terminal
•Antenna
•Mounting bracket and hardware
•2475 DC power supply cable
You may also need the following equipment (sold and ordered separately) to install the
terminal:
•DC power supply kit (10 to 36 VDC kit or 15 to 96 VDC kit)
•External power supply and power supply adapter cable
•Rail mount accessory and hardware
•Scanner and scanner cables
•RS-232 serial communications cable
Before you install the terminal, you should follow the guidelines for mounting the
terminal.
Guidelines for Mounting the Terminal
Before you install the mounting bracket, read these guidelines:
•Mount the 2475 where the operator can easily see the screen and use the keypad. If
possible, you should mount the terminal in a location that avoids glare from
overhead lighting and sunlight.
•Route all cables to minimize exposure to damage. Make sure the cables will not be
pinched or rubbed by any moving parts on the vehicle. In some applications, you
may need to sheath the cable to prevent it from being pinched.
•Secure the power cables at least every 45 cm (18 in) throughout the length of the
cable run—use adjustable clamps or tie-wraps to secure the cables.
Trakker Antares 2475 Vehicle-Mount Terminal Installation Instructions
6
Required Tools and Materials
You need the tools and materials listed next to install your 2475. These tools and
materials are not supplied with the terminal.
•Common hand tools and mounting hardware
•Electric drill and drill bits
•Wire crimping and stripping tool
•Heatshrink tubing
•Heat gun
Installing the Terminal and Connecting Devices
The steps to install your 2475 depend on the mounting location and the accessories you
want to attach to the terminal.
To install the 2475
1. Attach the antenna to the 2475.
2. Install the terminal on a vehicle or on a surface in an office environment.
3. Install and connect the DC power supply or the external power supply (office
location only).
4. Attach a scanner.
5. Connect to serial devices.
6. Fully charge the backup battery.
These procedures are described in detail in the next sections.
Trakker Antares 2475 Vehicle-Mount Terminal Installation Instructions
7
Attaching the Antenna
The antenna is shipped with the terminal. Remove the
antenna from the shipping box and attach the antenna
as shown.
You can also use an Intermec-approved accessory
antenna to improve RF communications. For more
information, see your Intermec sales representative.
Caution
Make sure all components with antennas are at least
0.3 m (1 ft) apart when power is applied. Failure to
comply could result in equipment damage.
Conseil
Assurez-vous que la distance entre tous les éléments
avec antennes soit d’au moins 0.3 mètres (un pied)
avant de faire la connexion avec l’alimentation
2475I009.eps
électrique, faute de quoi vous risquez d’endommager votre installation.
Installing the Terminal
Before you install the terminal, read the “Guidelines for Mounting the Terminal”on
page 5. You can use the mounting bracket to mount the 2475 on a vertical or horizontal
surface.
The mounting bracket ships in three separate pieces: two identical mounting plates and
one mounting arm.
Mounting
plate 1
Mounting
plate 2
Mounting
arm
2475I043.eps
Trakker Antares 2475 Vehicle-Mount Terminal Installation Instructions
8
To install the mounting bracket, you must complete these steps:
1. Attach one of the mounting plates to the 2475.
2. Install the other mounting plate and the mounting arm on a mounting surface.
3. Attach the 2475 to the mounting arm.
Each of these steps is described in the following procedures. You can also use the rail
mount accessory to mount the terminal to a rail on a vehicle. For help, see “Using the
Rail Mount”on page 10.
To attach a mounting plate to the 2475
1. Position the mounting plate so that the holes on the mounting plate align with the
holes on the back plate of the terminal. Make sure that the mounting plate ball is
oriented toward the top of the 2475 as shown.
2475I011.eps
Tapered head
screws (4 places)
2. Insert the four tapered head screws to attach the mounting plate to the terminal.
Tighten the tapered head screws with a Phillips #3 screwdriver.
Trakker Antares 2475 Vehicle-Mount Terminal Installation Instructions
9
To install the other mounting plate and the mounting arm on the mounting surface
1. Using the mounting plate as a template, mark and drill the holes in the vertical or
horizontal mounting surface.
Mounting
surface
Mounting
plate
2475I004.eps
2. Attach the mounting plate using appropriate hardware (not provided) through each
of the holes in the mounting plate and the mounting surface.
3. Attach the mounting arm to the mounting plate on the vehicle.
a. Squeeze the top of the mounting arm. The top of the mounting arm contains the
spring.
Spring
Mounting
arm
2475I005.eps
b. Position the bottom of the mounting arm over the ball on the mounting plate,
and release the mounting arm.
Trakker Antares 2475 Vehicle-Mount Terminal Installation Instructions
10
To attach the 2475 to the mounting arm
1. Attach the terminal and mounting plate assembly to the mounting arm, and adjust
the terminal to the best-possible viewing angle for the vehicle operator.
2. Tighten the knob to secure the terminal to the mounting arm.
Mounting
arm
Mounting
plate (2475
not shown
for clarity)
2475I008.eps
3. Periodically inspect the knob on the mounting arm to make sure it is still tight.
Check the mounting bracket assembly for any signs of fatigue, such as cracking,
which may develop over extended use in extreme (vibration) environments. Replace
any damaged hardware immediately to ensure continued, safe operation.
Using the Rail Mount
You can use the rail mount accessory (Part No. 072363) to attach the 2475 to a square
or rectangular rail on a vehicle.
Note: The rail mount can be installed on a rail that is up to 5 x 3.8 cm (2 x 1.5 in). Do
not install the rail mount on a rail that is larger than 5 x 3.8 cm (2 x 1.5 in).
Otros manuales para Trakker Antares 2475
2
Tabla de contenidos
Otros manuales de PDA de Intermec
Intermec
Intermec CN3E Series Guía
Intermec
Intermec CK60 Ethernet Multidock Manual
Intermec
Intermec Janus 2010 Instrucciones de instalación y funcionamiento
Intermec
Intermec 1007CP01 Manual de usuario
Intermec
Intermec PEN*KEY 6400 Manual de usuario
Intermec
Intermec CN51 Manual de usuario
Intermec
Intermec JANUS JG2010 Manual de usuario
Intermec
Intermec CK60 Ethernet Multidock Manual
Intermec
Intermec PEN*KEY 6620 Manual de uso y cuidado
Intermec
Intermec Trakker Antares 2410 Manual
Intermec
Intermec 6212 Manual de usuario
Intermec
Intermec Trakker Antares 2425 Manual
Intermec
Intermec CN51 Manual de usuario
Intermec
Intermec Trakker Antares 2425 Manual de usuario
Intermec
Intermec CK71 Manual de usuario
Intermec
Intermec 600 Series 602 Manual de usuario
Intermec
Intermec CK32 Manual
Intermec
Intermec Trakker Antares 2415 Manual
Intermec
Intermec 6650 Manual de usuario
Intermec
Intermec CK61 Manual
