Intermec JANUS JG2010 Manual de usuario

P/N 065714-001

User’s

Manual

JANUS

™

2010

Hand-Held Computer (4MB)

IntermecCorporation

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

U.S. service and technical support: 1-800-755-5505

U.S. media supplies ordering information: 1-800-227-9947

Canadian service and technical support: 1-800-688-7043

Canadian media supplies ordering information: 1-800-268-6936

Outside U.S. and Canada: Contact your local Intermec service supplier.

The information contained herein is proprietary and is provided solely for the purpose of allowing

customers to operate and/or service Intermec manufactured equipment and is not to be released,

reproduced, or used for any other purpose without written permission of Intermec.

Information and specifications in this manual are subject to change without notice.

1997 by Intermec Corporation

The word Intermec, the Intermec logo, JANUS, IRL, TRAKKER, Antares, Duratherm, Precision

Print, PrintSet, Virtual Wedge, and CrossBar are either trademarks or registered trademarks of

Intermec Corporation.

CardID™ and CardSoft™ are trademarks of SystemSoft Corporation. Some of the information in this

manual is based on copyrighted material contained in the CardSoft™ 3.1 Software User’s Guide,

published by SystemSoft Corporation, 1992-1994, Natick, Massachusetts.

Throughout this manual, trademarked names may be used. Rather than put a trademark (™ or )

symbol in every occurrence of a trademarked name, we state that we are using the names only in an

editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.

Contents

iii

Contents

Before You Begin xix

Warranty Information xix

Safety Summary xix

Warnings and Cautions xx

About This Manual xx

Suggested Reading xxvi

Getting Started

What Is the JANUS 2010 Reader? 1-3

Accessories for the Reader 1-4

JANUS 2010 Models and Options 1-5

Using the Reader for the First Time 1-6

Unpacking the Reader 1-6

Charging the NiCad Battery Pack 1-7

Installing the NiCad Battery Pack 1-8

Turning On the Reader for the First Time 1-9

Setting the Time and Date 1-10

Attaching a Wand or Scanner 1-11

Verifying That the Reader Is Operating Correctly 1-12

Turning the Reader On and Off 1-13

Where Do You Go From Here? 1-14

Learning How to Use the Reader

JANUS 2010 Features 2-3

Using the Alphanumeric Keypad 2-4

Finding the Special Keys 2-5

How to Type the Characters Printed on the Keypad 2-6

How the Ctrl, Alt, and Shift Keys Work 2-7

How the Compound Function Key Works 2-8

Capitalizing All Characters 2-10

Learning How to Use the Cursor Keys 2-11

Using the Number Pad 2-13

Finding Out If the Number Pad Is Enabled or Disabled 2-16

How to Enter ASCII Characters 2-16

JANUS 2010 Hand-Held Computer User’s Manual (4MB)

Using the Large Numeric Keypad 2-17

Finding the Special Keys 2-17

How to Type the Characters Printed on the Keypad 2-18

How to Type Other Characters 2-19

How to Use the Reader’s Display 2-20

Choosing the Display Sizes and Parameters 2-21

Using Text or Graphics Mode 2-23

Using the Display as a Viewport 2-23

Trying Out the Viewport 2-24

What Are Viewport Movement Steps? 2-25

Moving the Viewport 2-25

If You Cannot See the Cursor 2-27

Adjusting the Display From the DOS Prompt 2-27

Understanding the Icons 2-29

Understanding the Reader’s Audio Signals 2-31

Demonstrating the Reader’s Audio Signals 2-33

Using a Headphone or Earphone 2-33

Locating the Communications Ports 2-34

Learning About the Reader’s Batteries 2-35

Lithium Bridge Battery 2-35

How to Maximize the Internal Bridge Battery Life 2-35

Installing the Battery Pack 2-36

Removing the Battery Pack 2-37

Checking the Power Remaining in the NiCad Battery Pack 2-38

Charging the Battery Pack 2-39

Disposing of the NiCad Battery Pack 2-39

Recognizing a Low or Discharged Battery 2-40

Managing Your Battery Power 2-41

Using an External Power Supply 2-42

Defining the Reader’s Drives 2-43

Managing the Reader’s Memory and Disk Space 2-44

Learning About the Software

What Software Is Provided With the Reader? 3-3

What Software Is Provided on the Companion Disks? 3-5

Using DOS Commands 3-6

Contents

Defining the Startup Files 3-7

AUTOEXEC.BAT File 3-7

CONFIG.SYS File 3-9

MS-DOS Startup Menu 3-11

Learning How to Change the Contents of Drive C 3-11

Using Auto-Loader to Change Drive C 3-14

Installing Auto-Loader on Your Host Computer 3-14

Using an External Power Supply 3-16

Adding or Editing Files on Drive C 3-16

Replacing All Files on Drive C 3-18

Deleting Files From Drive C 3-19

Copying One Image File to More Than One Reader 3-21

Using MakeDisk and PutDisk to Change Drives C or D 3-24

Deciding Where to Run MakeDisk 3-24

Creating and Filling the Working Source Directory 3-25

Creating the New Image File 3-26

Loading the New Image File 3-26

Examples of Using MakeDisk and PutDisk 3-28

Creating and Using a Physical RAM Drive 3-32

Understanding When Files Are Saved or Lost 3-32

Deciding How Much Memory to Use for RAM Drives 3-33

Creating a RAM Drive 3-33

Programming for the Reader 3-35

Using JANUS PSK and JANUS Application Simulator 3-36

Using IRL and PC-IRL 3-36

Making PSK Applications That Work With BFT 3-37

Preparing Applications to Recover From Lockups 3-37

Using Reader Services in Applications 3-37

Making More Memory Available on the Reader 3-38

Not Installing the PC Card Drivers 3-39

Unloading and Loading Reader Wedge TSR 3-39

Understanding the Bar Code Wedge 3-40

Enabling Direct Hardware Wedge Functions 3-40

Using the Wedge Configuration Program 3-41

JANUS 2010 Hand-Held Computer User’s Manual (4MB)

Using PC Cards in the Reader

Learning About PC Cards 4-3

What Is PCMCIA? 4-3

Features of the JANUS PC Card Software 4-4

Locating the PC Card Drives 4-4

Which PC Cards Are Supported by JANUS? 4-5

Which Expansion Cards Are Recommended? 4-5

Which Memory PC Cards Are Recommended? 4-5

Configuring the Reader to Reset the Type I Drive 4-6

Inserting and Removing PC Cards 4-8

Inserting Cards Into the Type I PC Card Drive 4-8

Inserting Cards Into the Type II Drive 4-11

Reader Beeps for PC Cards 4-14

Configuring, Formatting, and Using PC Cards 4-14

Preparing to Use ATA Cards 4-15

Initializing and Formatting an ATA Card 4-16

Using an ATA Card 4-17

Preparing to Use Flash Cards 4-18

Erasing a Previously Formatted Flash PC Card 4-18

Formatting a Flash PC Card 4-19

Using a Flash PC Card 4-21

Preparing to Use I/O Cards 4-21

Configuring the JANUS device to Use an I/O Card 4-22

Resetting the PC Card Drive for I/O Cards 4-22

Preparing to Use SRAM Cards 4-23

Formatting an SRAM PC Card 4-23

Using the SRAM PC Card 4-24

Replacing Lithium Batteries in an SRAM Card 4-24

Managing the Power on the PC Card Drive 4-25

Managing the PC Card Drivers in the Startup Files 4-27

Drivers in CONFIG.SYS 4-27

Drivers in AUTOEXEC.BAT 4-28

Tips for Enabling PC Card Drivers 4-28

Contents

vii

Configuring the Reader

About the Configuration Parameters 5-3

Choosing the Symbologies the Reader Will Decode 5-3

Specifying How the Reader Will Communicate 5-4

Controlling How the Reader Will Operate 5-4

About the Configuration Files 5-4

Configuring the Reader With Configuration Files 5-4

Creating Configuration Files 5-5

Creating Multiple Configuration Files 5-5

Backing Up Your Configuration Files 5-6

How to Configure the Reader 5-6

Using the Interactive Configuration Application 5-7

Selecting Menus and Commands 5-8

Filling In Fields, Marking Check Boxes, and Saving Changes 5-8

Using a Series of Screens to Configure a Parameter 5-9

Using Multiple Configuration Files 5-9

Configuring the Reader by Scanning Bar Codes 5-11

Configuring the Reader With IRL Z Commands 5-12

Configuring the Reader With PSK Functions 5-12

Sending Commands From a Host Computer 5-12

Editing a Configuration File 5-13

Loading a Configuration File From the DOS Prompt 5-14

Loading a Configuration File Whenever You Boot 5-15

Restoring the Reader’s Default Configuration 5-16

Recording Your Reader’s Configuration 5-16

Networking the Reader

How the JANUS 2010 Fits Into Your Network 6-3

Working With JANUS COM Ports 6-6

Identifying JANUS COM Ports 6-6

Examining the COM1 Optical Port Signals 6-7

Understanding How IRQs Affect COM Ports 6-7

Designating the Scanner Port as COM2 6-8

Planning the Network Connection 6-9

Choosing a Communications Application 6-9

Choosing a Communications Protocol 6-10

Choosing a Protocol Handler 6-11

JANUS 2010 Hand-Held Computer User’s Manual (4MB)

viii

Configuring the Reader for Communications 6-12

Selecting the COM Port 6-13

Configuring the Communications Protocols 6-13

Multi-Drop Protocol Parameters 6-14

PC Standard Protocol Parameters 6-14

Point-to-Point Protocol Parameters 6-14

Polling Mode D Protocol Parameters 6-14

User-Defined Protocol Parameters 6-15

Activating One Communications Protocol 6-15

Loading and Unloading a Protocol Handler 6-15

Loading and Unloading a Protocol Handler at the DOS Prompt 6-16

Loading a Protocol Handler When You Boot the Reader 6-16

Loading and Unloading a Protocol Handler With a Batch File 6-17

Loading and Unloading a Protocol Handler With an Application 6-18

Specifying a Value for the FIFO Control Register 6-18

Connecting the Reader to Another Device 6-21

Running Interlnk to Transfer Files 6-23

Differentiating Between Client and Server 6-23

Example of Using Interlnk 6-24

Interlnk System Requirements 6-26

Installing Interlnk on the Host Computer 6-26

Making the Host Computer the Client 6-27

Making the Reader the Client 6-29

Interpreting the Server’s Status Screen 6-30

Redirecting Drives From the DOS Prompt 6-32

Exiting Interlnk 6-33

Restarting Interlnk 6-33

Running Communications Manager 6-34

Using Communications Manager Menus 6-34

Selecting Menus and Commands 6-36

Moving Around the Screen and Filling In Fields 6-36

Exiting Screens and Saving Changes 6-37

Using a Series of Screens to Configure a Parameter 6-37

Exiting Communications Manager 6-37

Typing Commands at the DOS Prompt 6-38

Downloading Applications Across the Network 6-38

Examples of Using BFT 6-39

Examining a Typical BFT Session 6-41

Preparing the Reader and Host Computer for BFT 6-42

Differentiating Between Client and Server 6-43

Starting an Application When the FTA Terminates 6-45

Using FTA Commands on the Reader 6-45

Contents

Typing FTA Commands on the Reader 6-45

Learning the Syntax of FTA Commands 6-46

Editing the FTA Initialization File 6-48

Working With IRL

Learning About IRL 7-3

Using the IRL Desktop 7-4

Opening the IRL Desktop 7-4

Closing the IRL Desktop 7-5

Exploring the IRL Desktop User Interface 7-5

Selecting Menus and Commands 7-7

Moving the Cursor Through the Screen 7-7

Exiting a Screen 7-7

Practicing With the IRL Desktop User Interface 7-7

Executing Commands in the IRL Desktop 7-8

Running an IRL Program 7-8

Pausing an IRL Program 7-9

Exiting an IRL Program 7-9

Downloading an IRL Program 7-10

Transmitting IRL Files 7-10

Receiving IRL Files 7-11

Clearing IRL Data Files 7-11

Specifying the Path for Programs and Data Files 7-12

Setting the Path With an Environment Variable 7-13

Including a Data File Path in the OPEN Command 7-14

Selecting the Path From the IRL Desktop 7-14

Resuming IRL Programs 7-15

Exiting a Program So You Can Resume It Later 7-15

Resuming a Program From the DOS Prompt 7-16

Resuming a Program From the IRL Desktop 7-16

Freeing Enough Memory to Run an IRL Program 7-17

IRL Reader Commands 7-18

JANUS 2010 Hand-Held Computer User’s Manual (4MB)

Preparing the Reader for International Use

Configuring the Reader for a Language 8-3

Installing Auto-Loader on Your Host Computer 8-3

Choosing a Method to Configure a Language 8-5

Using the LOADADD Batch File With the NLS Option 8-5

Using the LOADNEW Batch File 8-6

Using the LOADLANG Batch File 8-8

Using an International Keypad 8-9

Finding the Special Keys 8-9

How to Type the Characters Printed on the Keypad 8-10

Typing the Characters On and Above the Alphabetic Keys 8-10

Typing the Characters On and Above the Numeric Keys 8-11

Typing Diacritical or Accent Marks 8-12

Using the Alt Key 8-12

Capitalizing All Characters 8-13

Using the Number Pad 8-13

Using DOS Code Pages 8-14

Using the French Keypad 8-15

Using the German Keypad 8-16

Using the Italian Keypad 8-17

Using the Spanish Keypad 8-18

Booting and Resetting the Reader

Booting the JANUS Reader 9-3

Warm Booting the Reader 9-3

Cold Booting the Reader 9-4

Resetting the Reader 9-5

Forcing the Reader to Turn Off 9-5

Breaking Out of an Application 9-5

Displaying the Boot Loader Menu 9-6

Limiting Access to Advanced Reader Commands 9-8

Using Storage Mode to Preserve the Bridge Battery 9-9

Dumping the Reader’s 640K Conventional Memory 9-11

Loading Flash Memory 9-13

Otros manuales para JANUS JG2010

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de PDA de Intermec

Intermec

Intermec 6500 Manual de uso y cuidado

Intermec

Intermec NORAND 6642 Manual de usuario

Intermec

Intermec 6110 Manual de usuario

Intermec

Intermec CN4 Manual de usuario

Intermec

Intermec PEN*KEY 6620 Manual de usuario

Intermec

Intermec Trakker Antares 2455 Manual

Intermec

Intermec Trakker Antares 2420 Manual de usuario

Intermec

Intermec Trakker Antares 2400 Manual de usuario

Intermec

Intermec CN3E Series Manual de usuario

Intermec

Intermec Trakker T2090 Manual de usuario

Intermec

Intermec PEN*KEY 6200 Manual de usuario

Intermec

Intermec Trakker Antares 2460 Manual de usuario

Intermec

Intermec Trakker Antares 2415 Manual

Intermec

Intermec PEN*KEY 6400 Manual

Intermec

Intermec Trakker Antares 2420 Manual de usuario

Intermec

Intermec Trakker Antares 2400 Manual de usuario

Intermec

Intermec CN2B Manual

Intermec

Intermec 6220 Manual de usuario

Intermec

Intermec 751G Manual

Intermec

Intermec JANUS JG2050 Manual de usuario

Intermec

Intermec PEN*KEY 6100 Manual de usuario

Intermec

Intermec 600 Series 602 Manual de usuario

Intermec

Intermec CN4 Manual de usuario

Intermec

Intermec Trakker Antares 2480 Manual de usuario

Manuales populares de PDA de otras marcas

SPOT

SPOT SPOT Manual de usuario

Palm

Palm handheld Manual de usuario

Winmate

Winmate E500QK Manual de usuario

Getac

Getac PS236 Manual de usuario

Sharp

Sharp CE-1600P Manual de usuario

HTC

HTC PHAR100 Manual de usuario

Mindeo

Mindeo M40 Manual de usuario

Acer

Acer n30 Manual de usuario

ASCOM

ASCOM 9D24 EX Manual de usuario

Unitech

Unitech PA520BTNF Manual de usuario

HandHeld

HandHeld Nautiz X3 Manual de usuario

Casio

Casio PALM Manual de usuario

Sharp

Sharp TM-20 Guía de inicio rápido

Atid

Atid AT870 Manual de usuario

AML

AML M7225 Manual de usuario

Audiovox

Audiovox Maestro Manual técnico

Casio

Casio PV-750 Plus Manual de instrucciones y seguridad

Unitech

Unitech PT630 Manual de usuario