Intermatic ET9232 Guía

ET9232 Ethernet Module

Ethernet Module Replacement Instructions

MODEL ET9232

• Turnpoweroffatmainpanelbeforeservicingthisswitchortheequipmentitcontrols.

• Morethanonedisconnectswitchmayberequiredtode-energizetheequipmentbeforeservicing.

WARNING

Keeplow-voltagewiringseparatefromhigh-voltagewiring,includingdeadfrontmaterialbetweenwiringareas.Separate

conduitmaybeusedforlow-voltagewiringifnolinevoltagewiringispresent.

Risk of Fire or Electric Shock

Ethernet Module Replacement Guidelines

There are separate Ethernet Module replacement instructions for the one and two circuit time

switches and the 4 to 16 circuit time switches. Be sure to follow the applicable Ethernet Module

replacement instructions for your ET90000 time switch.

ReplacingEthernetModuleon1or2CircuitTimeSwitch

Follow the instructions below to replace an Ethernet Module on a 1 or 2 circuit ET90000 time switch.

1. Disconnect power to the time switch.

2. Open the time switch enclosure cabinet door.

3. At the bottom of the time switch, disconnect the Ethernet cable from the port in the Ethernet

module plastic enclosure.

4. Disconnect the Ethernet module ribbon cable connector plug from the terminal connector.

5. Remove the rivets that secure the Ethernet Module and remove the module from the plastic insulator.

6. Dispose of the rivets and module.

7. Align the new Ethernet module plastic enclosure over the holes on the plastic insulator and

secure the plastic enclosure with the rivets provided with the new module.

8. Connect the ribbon cable connector plug to the terminal connector.

9. Insert the Ethernet cable into the Ethernet port in the enclosure.

10. Close the time switch enclosure door.

11. Return power to the time switch.

CAUTION Risk of Unintended Equipment Operation

Figure 1. ET90000 with Ethernet Module components shown

Terminal

Connector

Ribbon

Cable

Ethernet

Cable port

Rivet (2)

Ethernet Module

Plastic Enclosure

ReplacingEthernetModuleon4to16CircuitTimeSwitch

Follow the instructions below to replace an Ethernet Module on a 4 to 16 circuit ET90000 time switch.

1. Disconnect power to the time switch.

2. Open the time switch enclosure door.

3. Remove the screws from the deadfront and remove the deadfront from the enclosure. Set aside

the deadfront and screws for re-use.

4. Remove the screw that secures the time switch controller door assembly. Set aside the screw

for re-use.

Deadfront Screws

Deadfront

Figure 2. Removing the deadfront.

Figure 3. Time switch controller door assembly with screw.

5. On the inside of the door assembly, disconnect the Ethernet cable from the module.

6. Disconnect the Ethernet module ribbon cable connector plug from the applicable terminal

connector.

7. Remove the three screws that secure the Ethernet Module and remove the module from inside

of the door assembly. Set aside the screws for re-use.

8. Open the new ET9232 Ethernet module plastic enclosure and remove the board.

9. Discard the plastic enclosure.

10. Remove and discard the ribbon cable from the Ethernet module board.

11. Align the module board over the holes on the door assembly and secure the board with the

screws previously removed in step 7.

12. Connect the ribbon cable connector plug to the applicable terminal connector. See Figure 4.

13. Insert the Ethernet cable into the Ethernet port on the module.

14. Close the door assembly and secure with the screw previously removed in step 4.

15. Return the deadfront to the enclosure and secure with the screws previously removed in step 3.

16. Close the time switch enclosure door.

17. Return power to the time switch.

Figure 4. Removing the Ethernet Module.

Figure 5. Ethernet module plastic enclosure.

158--01118

LIMITED ONE YEAR WARRANTY

If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace

it, at its sole option, free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply

to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to

unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of

the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as

this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE

WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY

AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME

STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) completing a warranty claim

on line at www.intermatic.com. This warranty is made by: Intermatic Incorporated, Customer Service 7777 Winn Rd. Spring Grove, Illinois 60081-9698.

For warranty service go to: http://www.intermatic.com or call 815-675-7000.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081

www.intermatic.com

Tabla de contenidos

Otros manuales de Unidad de control de Intermatic

Intermatic

Intermatic DDT40 Manual de usuario

Intermatic

Intermatic SS7 SERIES Manual de usuario

Intermatic

Intermatic K4536SST Manual

Intermatic

Intermatic K4621 Manual de usuario

Intermatic

Intermatic K4251 Manual de usuario

Intermatic

Intermatic K4321C Manual de usuario

Intermatic

Intermatic ICUBE Manual de usuario

Intermatic

Intermatic PF1100 SERIES Manual de usuario

Intermatic

Intermatic SS8 Series Manual de usuario

Intermatic

Intermatic Grasslin Talento Smart LAN Manual de usuario

Intermatic

Intermatic LC2000 Instrucciones de funcionamiento

Intermatic

Intermatic NE3BC Manual de usuario

Intermatic

Intermatic K4000 series Manual de instrucciones

Intermatic

Intermatic K4121M Manual de usuario

Intermatic

Intermatic P1353ME Manual de usuario

Intermatic

Intermatic LC4500 Series Manual de instrucciones

Intermatic

Intermatic LC4 Series Manual de instrucciones

Intermatic

Intermatic T40000R Series Manual

Intermatic

Intermatic K4023C Manual de instrucciones

Intermatic

Intermatic ET9250 Guía de configuración

Intermatic

Intermatic K4141C Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario