Intergraph TDZ 2000 GL2 Workstation Manual de usuario

DHA0287A5, 10/99

TDZ 2000 GL2 Workstation

Late-Breaking News

General

System Audio

If you change the default IRQ assignments in the system BIOS or if you reprogram the BIOS, you

must set the Sound Blaster 16 audio card’s IRQ to 5 using the driver’s SETUP.EXE program. The

SETUP.EXE program is part of the SNDBLSTNTDRV system software product available in InterSite

Version Manager. For instructions on reinstalling the driver software, see the README.TXT file

delivered with the driver. See System Setup for information on configuring the BIOS.

SCSI Disk Drive Configurations

The system attempts to boot from an IDE drive before it attempts to boot from a SCSI drive. Do

not restart the system with a bootable CD in the CD-ROM drive.

You can change the system’s boot device order in the system BIOS to boot first from a diskette,

then from a SCSI disk drive, and then from the ATAPI CD-ROM drive. See System Setup for

information on using BIOS Setup to do this.

Symbios SCSI Controller

Your system may hang intermittently while booting, at the “Z” logo screen with a blinking cursor

or after scanning the devices connected to the Symbios SCSI controller. If this happens:

1. Restart the system and run BIOS Setup.

2. Go to Advanced CMOS Setup.

3. Disable Quick Boot.

4. Save the change and exit from BIOS Setup.

See System Setup for information on using BIOS Setup. This procedure marks unused IDE ports

as “not installed,” so you must repeat it if you add any IDE devices later.

You may need to use the SCSI Configuration Utility to configure the operation of SCSI peripherals

connected to the controller. You can find the SCSI Configuration Utility (PCI_CFG.EXE) on the

SYSUTIL diskette delivered with the system. This utility lets you configure the SCSI controller,

perform a low-level format on a SCSI disk drive, select boot order, and verify media. See SCSI

Configuration Utility Help for instructions on using the SCSI Configuration Utility.

Targa 2000 RTX Card

To use a Targa 2000 RTX card with the system’s Sound Blaster 16 audio card, reserve IRQ 5 for

ISA/EISA use in the system BIOS (under PCI/Plug and Play Setup). See System Setup for

instructions on using BIOS Setup to do this.

PC Card Adapter

If you change the default IRQ assignments in the system BIOS or if you reprogram the BIOS, you

must reserve IRQ 11 for use with the PC Card adapter. This ensures correct operation of the PC

Card adapter. See the System Board Manual for information on using BIOS Setup.

When installing the audio card driver software on a system with a PC Card adapter running

Windows NT 4.0, you may see a “new hardware found” message that asks you which driver to

install. Select Do not install a driver. The PC Card adapter will work and the “new hardware

found” message will not display again.

Operating System Support for USB Peripherals

Your system includes Universal Serial Bus (USB) ports for USB peripherals. Windows 98 and

Windows 95 Service Release 2.1 (or later) support USB peripherals. Windows NT 4.0 does not

support USB peripherals. Microsoft will add USB support to a future Windows NT release.

System BIOS

See System Setup for detailed information on BIOS configuration. Do not use the BIOS

information the System Board Manual. Information on the following BIOS Setup parameters in

System Setup has been updated:

♦Under Standard CMOS Setup/Boot Sector Virus Protection, the Optimal default setting is

Disabled.

♦Under Advanced CMOS Setup/Default Primary Video, the Optimal default setting is PCI; the

other setting is AGP.

♦Under Advanced CMOS Setup/Processor Serial Number, the Optimal default setting is

Disabled. This parameter is for systems with Pentium III processors.

Pentium III Processors

Intel’s Streaming SIMD Extension Driver was installed on the system before shipment. This

driver increases performance for drivers and applications designed to take advantage of it. If you

reinstall the operating system, you should also reinstall this driver. You can find it in the QFE_SSE

system software product, which you can get from the Support pages on the World Wide Web

(http://www.intergraph.com/ics/) or the Intergraph System CD-ROM. See the README.TXT file

delivered with QFE_SSE for more information.

Pentium III processors require system BIOS version 1.21 or higher. 600 MHz Pentium III

processors require system BIOS version 1.24 or higher. You do not need to set system board

jumpers to match a Pentium III processor’s speed.

Windows NT 4.0

Ethernet Network Setup and Configuration

On a system equipped with an Ethernet network controller, note the following:

♦Network controller driver software is preinstalled. Operating system Setup no longer prompts

you to install networking.

♦Core network software and the NetBEUI network protocol are preinstalled. If you want to

connect the system to another type of network (such as TCP/IP), you must add the appropriate

network protocol using the Network applet in the Control Panel. Reinstall the appropriate

Windows NT 4.0 Service Pack software after making such changes, as recommended by

Microsoft.

Microphone Operation

If your system’s microphone does not function, try this. Double-click the speaker icon in the

taskbar tray to display the Volume Control. On the Options menu, click Properties, and then click

Recording. In the list of volume controls, check the box for the microphone, and then click OK.

3D Pipes Screen Saver and Dual-Screen AccelSTAR II Graphics

On a system with dual-screen AccelSTAR II graphics, the 3D Pipes screen saver does not display.

If you activate this screen saver, you will only see a black screen. A driver fix for this problem is

under investigation. When available, a revised driver will be posted to the Support pages on the

World Wide Web (http://www.intergraph.com/ics/) and to the Intergraph Bulletin Board Service

(1-256-730-8786).

Automatic Shutdown

If you reinstall Windows NT, be sure to reinstall the Automatic Shutdown Utility, which is

available as backup media (SHUTDOWN) in InterSite Version Manager. If you do not, pressing the

system’s Standby button momentarily will put the system in a “suspend” state from which it will

not awaken. You will have to turn system power off and on to return to normal operation, and

chkdsk will run when the system restarts.

Windows 98

Windows 98 and

System Setup

Your System Setup document may contain Windows 95 information. If your system was delivered

with Windows 98, refer to the following items for information that replaces or supplements the

Windows 95 information in the System Guide.

Windows 95 Drivers

Intergraph Computer Systems has preinstalled some Windows 95 drivers on systems delivered

with Windows 98. These drivers are provided as backup media in InterSite Version Manager.

Make copies of these drivers, as you may need them to reinstall the operating system and

associated system software.

The installed Windows 95 drivers were certified on Windows 98, and can be used until vendor-

supplied Windows 98 versions are available. When they have been certified for use, Windows 98

versions of these drivers will be posted to the Support pages on the World Wide Web

(http://www.intergraph.com/ics/) and to the Intergraph Bulletin Board Service

(1-256-730-8786).

Booting into Safe Mode

The graphics driver software installed on your system is set for a display resolution of 1024 x 768.

If you connect the system to a monitor that does not support this resolution, the system may boot

into Safe Mode and the standard VGA display resolution of 640 x 480. If the system boots into a

distorted video display, you can restart the system and, before Windows starts, press F8 to boot

into Safe Mode.

Once the system is in Safe Mode, right-click the operating system desktop and select Properties.

Click the Settings tab, and set an appropriate display resolution for the monitor and (if needed) and

appropriate monitor type. Then restart the system.

Millennium II Driver and MGAPowerdesk

On a Windows 98 system with Millennium II graphics, the driver software and MGA Powerdesk

software is preinstalled, and is available as backup media in InterSite Version Manager (on

multiple diskettes). If you reinstall Windows 98, reinstall the Millennium II driver:

1. Let Windows 98 Setup detect the Millennium II graphics card.

2. After Windows 98 Setup completes, insert disk 1 of the Millennium II Windows 95 driver

(MILL2DRVW95) in the system’s floppy disk drive.

3. Right-click the desktop and go to Properties/Display/Settings/Advanced/Adapter.

4. Select to change the controller.

5. In the Updated Device Driver Wizard, select to search for a better driver than the one in use.

6. When prompted, select the floppy disk drive containing disk 1 of MILL2DRVW95.

7. Follow the instructions to complete installation of the driver and restart the system.

To use the MGA Powerdesk features, you must reinstall the MGA Powerdesk software separately:

1. Insert disk 1 of the Millennium II Windows 95 driver (MILL2DRVW95) in the system’s floppy

disk drive.

2. In Explorer, find and double-click the SETUP.EXE file on the diskette.

3. When prompted for an installation type, select the Typical option.

4. When prompted, remove disk 1 from the system’s floppy disk drive and insert disk 2.

5. Follow the instructions to complete installation of the Powerdesk software.

MGA Powerdesk includes support for Intergraph Computer Systems monitors. To select the

appropriate Intergraph monitor type, right-click the operating system desktop and go to

Properties/Settings/Advanced/MGA Monitor.

Software for Zip or Jaz Drives

If you purchased an Iomega Jaz or Zip drive with your system, the software included with the drive

options may not function properly in Windows 98. Iomega will release software that is fully

compatible with Windows 98 in August 1998. You will be able to get this software from Iomega’s

Web pages at http://www.iomega.com.

and trademark law. This document may not, in whole or in part, be reproduced in any form or by any means, or be used to make any

derivative work, without written consent from Intergraph Computer Systems.

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of the

rights in technical data and computer software clause at DFARS 252.227-7013. Unpublished rights are reserved under the copyright

laws of the United States.

Intergraph Computer Systems, Huntsville AL 35894-0001

Notice

Information in this document is subject to change without notice and should not be considered a commitment by Intergraph Computer

Systems. Intergraph Computer Systems shall not be liable for technical or editorial errors in, or omissions from, this document.

Intergraph Computer Systems shall not be liable for incidental or consequential damages resulting from the furnishing or use of this

document.

All warranties given by Intergraph Computer Systems about equipment or software are set forth in your purchase contract. Nothing

stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such

warrantites.

Otros manuales para TDZ 2000 GL2 Workstation

Tabla de contenidos

Otros manuales de De oficina de Intergraph

Intergraph

Intergraph TDZ 2000 GX1 Manual de usuario

Intergraph

Intergraph TD-200 Targa 2000 Manual de usuario

Intergraph

Intergraph TD-300 Manual de funcionamiento

Intergraph

Intergraph TD-x20 Setup Manual de usuario

Intergraph

Intergraph TDZ 2000 GL2 Workstation Manual de usuario

Intergraph

Intergraph TDZ 2000 GT1 Manual de usuario

Intergraph

Intergraph TDZ 2000 Manual de usuario

Intergraph

Intergraph Zx10 Ultra-Tower Manual de usuario

Intergraph

Intergraph TDZ 2000 GL1 Manual de usuario

Intergraph

Intergraph TD-x10 Setup Guía del usuario

Intergraph

Intergraph TD-2x Manual de usuario

Intergraph

Intergraph Zx10 6U Manual de lista de piezas

Intergraph

Intergraph TDZ 2000 GL1 Guía del usuario

Intergraph

Intergraph TD-260 Manual de lista de piezas

Intergraph

Intergraph TDZ 2000 GL2 Workstation Manual de usuario

Intergraph

Intergraph TDZ-300 Manual de funcionamiento

Intergraph

Intergraph TDZ 2000 GL2 Workstation Guía del usuario

Intergraph

Intergraph TDZ 2000 GX1 Manual de usuario

Intergraph

Intergraph TDZ 2000 GT1 Manual de usuario

Intergraph

Intergraph TD-300 Manual de funcionamiento

Intergraph

Intergraph Zx1 ViZual Workstation Guía del usuario

Intergraph

Intergraph TD-x20 Setup Guía del usuario

Intergraph

Intergraph TDZ-400 Deskside Manual de funcionamiento

Intergraph

Intergraph TD-22x Manual de lista de piezas

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario