Interfacom TAXITRONIC TXD70 Manual de usuario
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 01/06/2016
INSTALLATION MANUAL
TAXITRONIC TXD70
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 2
INDEX
1. INTRODUCTION......................................................................................................... 4
2. MOUNTING................................................................................................................. 4
2.1. LOCATION OF MX70........................................................................................... 4
2.2. MOUNTING TXD70.............................................................................................. 4
2.2.1. LOCATION OF TXD70................................................................................................. 4
2.3. ELECTRICAL INSTALLATION............................................................................. 5
2.4. CHARACTERISTICS............................................................................................ 5
2.5. INSTALLATION RECOMMENDATIONS .............................................................. 6
2.6. FIRST TIME TURN ON ........................................................................................ 7
2.7. HARDWARE TEST .............................................................................................. 7
2.8. CONFIGURATION PARAMETERS...................................................................... 8
2.8.1. GPRS GSM .................................................................................................................. 9
2.8.2. RT PARAMS............................................................................................................... 10
2.8.3. TICKETS .................................................................................................................... 11
2.8.4. INSTALLATION.......................................................................................................... 12
2.8.5. TOUCHSCREEN CALIBRATION............................................................................... 13
2.8.6. RT PARAMS 2............................................................................................................ 13
2.8.7. SOFT UPDATE .......................................................................................................... 13
2.8.8. KERN UPDATE.......................................................................................................... 14
2.9. SWITCH TO NORMAL MODE ........................................................................... 14
3. TAXIMETER CONFIGURATION ............................................................................... 15
3.1. CONFIGURING IMPULSE SIGNAL.................................................................... 15
3.1.1. PULL-UP CONFIGURATION ..................................................................................... 17
3.1.2. CALCULATION OF THE K CONSTANT.................................................................... 18
3.1.3. ENTERING CONSTANT K......................................................................................... 19
3.2. PROGRAMMING PASSWORDS........................................................................ 19
3.3. SETTING THE CALENDAR - CLOCK................................................................ 19
3.4. RESET TOTALIZERS......................................................................................... 20
3.5. RECORD THE TARIFF ...................................................................................... 20
4. SEALING................................................................................................................... 21
4.1. MX70.................................................................................................................. 21
4.2. TXD70................................................................................................................ 21
5. MAINTENANCE......................................................................................................... 22
5.1. SWITCH TO INSTALLER MODE ....................................................................... 22
5.2. HARDWARE TEST ............................................................................................ 22
5.3. REMOTE TEST.................................................................................................. 23
5.4. REPAIRS............................................................................................................ 23
5.5. SOFTWARE UPDATE........................................................................................ 24
5.5.1. FROM NORMAL MODE............................................................................................. 24
5.5.2. FROM INSTALLER MODE......................................................................................... 24
6. NAVIGATOR LICENSE MANAGEMENT................................................................... 26
7. VERSION CONTROL................................................................................................ 29
ANNEX I: HARDWARE TEST SUMMARY TABLE ........................................................... 30
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 3
DRAWINGS LIST
Drawing 1 Bracket assembly
Drawing 2 TXD70 mounting on bracket
Drawing 3 Connectors
Drawing 4 Electrical installation drawing
Drawing 5 Installation with armored cables
Drawing 6 TXD70 Plastic sealing
Drawing 7 TXD70 Sealing stickers position
Drawing 8.1 TXD70 Cable seals
Drawing 8.2 MX70 Cable seals
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 4
1. INTRODUCTION
This document describes the installation and parameterization of TAXITRONIC TXD70.
2. MOUNTING
2.1. LOCATION OF MX70
TXD70 must be installed so that passengers can’t see or access it, but the verification
office must be able to access it. Seals and serial numbers must be easily visible and
accessible upon verification at a verification office.
Preferred positions are inside the glovebox, under the passenger seat or similar.
It is necessary that the identification sticker and the seals are easy to inspect. For this
reason it is necessary to take care of the orientation, with the stickers looking to the
outside. Cables can’t cover neither the identification sticker nor the seals.
2.2. MOUNTING TXD70
The installation of the TXD70 is to be done on its support (See drawings 1 and 2). The
design of the support allows for 3-dimension orientation of the TXD70, so it is adapted to
different dashboard designs.
The adhesive base is ready to be adhered to plastics, and supports the temperature
ranges inside a vehicle.
The connection is done by only one connector on the back of TXD70. The tools necessary
for installing TXD70 are:
Fixed hexagonal key nº 15.
Allen key nº2, minimum length of the shaft 100mm.
Allen key nº3.
Screwdriver with head H1
Isopropyl alcohol (If there are previous installation or tariff seals to be removed)
The orientation of TXD70 is fixed by screwing the two Allen screws on the sides (points B
and C on drawing 2). The central screw which touches directly on the support ball is not
used (see drawings 1 and 2)
The height of TXD70 is fixed by screwing the central hexagonal key (Points A of drawing 2)
2.2.1. LOCATION OF TXD70
It is normally located on the vehicle dashboard, most times centered, so that both the
passenger and driver can clearly see it.
MX70 needs space enough to open the printer cover, so that the paper can be changed. It
can’t be too close to the windscreen, so that the magnetic card can be passed easily. It
must not interfere with the vehicle airbag, and it must be fitted as low as possible so as to
not obstruct the visibility of the road.
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 5
2.3. ELECTRICAL INSTALLATION
TXD70 admits power supplies between 9 and 30 V, which makes it compatible with the
current 12V and 24V vehicle batteries.
First perform all the connections with the unit disconnected from the car battery. When all
peripherals are connected, and then connect the power supply
If it is necessary to make an intervention in the installation, it is necessary to first
disconnect the main power supply cabling or fuse, and then modify the rest of the
installation.
Drawing 3 details all the TXD70 connectors.
If you use a serial roof light, look at the position of the white mark in the drawing
Install the cabling and peripherals according to the connections diagram in drawing 4.
If an emergency button is used:
- Solder together the brown wire with the yellow wire of the emergency button, and
protect the joint with a thermoretractile cover.
- If the Radiotaxi emergency function is not to be used, the brown wire should be
connected to Ground
2.4. CHARACTERISTICS
The dimensions of the units are:
Length mm
Height mm
Width mm
Weight g
MX70
80
60
32
132
TXD70
179
100
70
624
TXD70 is designed and certified to operate in an environment of electromagnetic class E3
(instruments powered by a vehicle battery) and in a mechanical environment class M3
(high and very high vibration level, such as in a vehicle).
The units are designed to operate indoors, in an temperature range of -25ºC / 70ºC and
without condensation, such as inside a vehicle.
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 6
2.5. INSTALLATION RECOMMENDATIONS
Disconnect the battery positive contact until the whole electrical installation is finished.
Any work on the terminal or accessory must be done with the device disconnected from
the battery or without the general fuse.
Always use the positive and negative directly from the battery, to get a more filtered
power supply and avoid false contacts.
Always connect the cables to the battery with a terminal, never by directly rolling the
cables around the battery contact.
If the cables crosses any edges, like metal edges, the cables must be protected with a
rubber protector
If the power supply cables are too long, they have to be cut to measure. They must
never be rolled.
In case the vehicle has a radio transmitter, separate the transmitter installation as
much as possible from the terminal and its wiring. The transmitter and the terminal
antennae also are to be as separated as possible.
Install all the units and connect the power. Finally connect the general fuse.
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 7
2.6. FIRST TIME TURN ON
Turn on the unit by pressing on the touchscreen.
The unit starts, showing a progress bar. Finally you get a screen with the message
“ENTER A VALID USB”
Connect the USB stick with installer key to the USB connector
A screen requests for the installer password
Enter the password and press OK.
2.7. HARDWARE TEST
Press “HW Test” to access the verification screens, which allow you to check the main
modules of TXD70. See the summary table in Annex I
To exit any of the screens press << Back
Finish the verification of all elements connected to TXD70 before passing to next step. The
verification has to include:
Alarm button
Contact key
Rooflights
Enter the PIN in TXD70 before inserting the SIM. TXD70 does not allow to use SIMs
without PIN in order to protect the taxi drivers against SIM’s robberies.
The SIM is to be inserted with the contacts pointing to the front of TXD70.
TXD70 supports 3.3 V and 1.8 V SIMs. Old 5 V SIMs are not supported.
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 8
2.8. CONFIGURATION PARAMETERS
When in the main Manufacturing screen, press “Configure”
The application configuration parameters will open.
These are not metrological parameters; therefore they are not subject to sealing. They can
be accessed by swiping an installer magnetic card.
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 9
2.8.1. GPRS GSM
GPRS APN
Identification of the GPRS network
Central Port
UDP Port of the central program
GPRS Suffix
GPRS Suffix, used as a second part of
the GPRS user.
Your network support will give you this
data if needed
Local Port
UDP Port of the local TXD70 application
GPRS User
Identification of the TXD70 in the GPRS
network
GPRS
Password
Password of the TXD70 in the GPRS
network
Central IP
Address
IP Address of the Radiotaxi central
This field can not be empty
PIN GSMA
Enter the GSM A PIN
If the SIM is not in:
1.- First enter the PIN
2.- Then the SIM can be entered, with
the contacts towards the front of TXD70
ANI GSMA
Enter the GSM A phone number
PIN GSMB
Not used
ANI GSMB
Not used
Mobitex Cent
Holland specific
INSTALLATION MANUAL TXD70 INTERFACOM, S.A
TXD70_Install_Manual_en_023.doc 10
2.8.2. RT PARAMS
Name
Name of license owner
License
License number
Plate Number
Plate number
NIF
Fiscal ID
Car ID
ID of the car in the Radiotaxi
Driver 1..4
Driver codes of the 4 drivers
Company
Company code
Used by the Prima application
Term SN
TXD70 serial number
This field can not be empty
2 Drivers/Shift
Number of drivers per shift
Used by the Working Time Control application
Pins ShiftNr
To change the Shift number
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Interfacom
