Intellinet 208338 Manual de usuario
intellinetnetwork.com
H.264 HDMI Over IP
Video Wall Extender
User Manual
Models 208338 & 208345
Important: Read before use. • Importante: Leer antes de usar.
2
H.264 HDMI Over IP Video Wall Extender User Manual
CONTENTS
Introduction ........................................................................................................... 3
Setup Components............................................................................................... 3
Hardware Features ............................................................................................... 3
Transmitter.............................................................................................................. 3
Receiver ................................................................................................................ 4
Installation Guide .................................................................................................. 4
Connect Devices................................................................................................... 5
Hardware Installation ........................................................................................... 5
Video-wall Diagram .............................................................................................. 6
VESA Mounting ..................................................................................................... 7
Installation Example .............................................................................................. 7
Management UI.................................................................................................... 8
Download the Management UI ........................................................................... 8
Select Interface ..................................................................................................... 8
Introduction to the Management UI .................................................................... 8
Management UI - Device...................................................................................... 9
Advanced Device Settings .................................................................................. 9
Management UI - Walls....................................................................................... 10
Create New Video Wall ....................................................................................... 10
Set Display Position.............................................................................................. 11
Bezel Correction .................................................................................................. 11
Management UI - Management........................................................................ 12
About ................................................................................................................... 13
Notes .................................................................................................................... 13
Additional Information ........................................................................................ 14
1 32 4 5 6 7
3
User Manual H.264 HDMI Over IP Video Wall Extender
Introduction
The H.264 HDMI Over IP Video Wall Extender offers a cost effective solution to complete a variety of AV setups,
including point-to-point, one-to-many, many-to-many and video-wall configurations. Both the transmitter
and receiver work together to provide Full-HD audio and video to TVs, projectors or monitors up to 100 m
(330 ft.) with nearly zero latency. This Extender works with any HDMI source such as a Blu-ray disk player, DVD
player, PC, notebook, gaming console (ex. SONY PlayStation®, Nintendo SwitchTM) and is HDCP compliant.
No software or utility is required to easily build a video-wall display. The transmitter (TX) and receiver (RX) include
rotary switches to create the desired set up (e.g., a 10-position switch for 10 TX-RX pairings and 16-position
switch for 1x2-, 2x2-, or 3x3-screen video-wall displays). When used with an IGMP-snooping-enabled Gigabit
Ethernet network switch, point-to-point, one-to-many, many-to-many configurations can exist on the same
IP LAN. This Extender is the perfect choice for displaying digital media in all kinds of environments and for all
kinds of purposes, including for surveillance systems, digital signage, trade shows, campuses, airports, shopping
centers and conference centers. Connect up to 10 Transmitters (#208338) and 246 Receivers (#208345).
Setup Components
• H.264 HDMI Over IP Video Wall Extender - Transmitter
• H.264 HDMI Over IP Video Wall Extender - Receiver
• Power adapters — 5 V / 2 A
• HDMI cables
• Mounting hardware (with Channel-ID selector tool)
• Hook-&-loop fastener
• Installation manual
Hardware Features
Transmitter
1 Reset
2 HDMI input port with lock
3 LEDs: status (upper, amber); power (lower, green)
4 Channel ID
5 LAN port
6 Power jack
7 Security-lock slot
1 6 7 82 3 4 5
4
H.264 HDMI Over IP Video Wall Extender User Manual
Receiver
1 Reset
2 Video display ID
3 HDMI output port with lock
4 LEDs: status (upper, amber); power (lower, green)
5 Channel ID
6 LAN port
7 Power jack
8 Security-lock slot
Installation Guide
Complete setup with the instructions below. Images for the setups follow in the Connect Devices chapter.
1 Use HDMI cable to connect the HDMI Input port on the Transmitter to the HDMI Output port on your source.
2 Use HDMI cable to connect the HDMI Output port on the Receiver(s) to the HDMI Input port on your display(s).
3 Use Ethernet cable to complete the desired setup:
a Point-to-point: connect the LAN port on the Transmitter to the LAN port
on the Receiver or to a network switch (to extend the signal).
b One-to-many and many-to-many: connect the LAN ports on the Transmitter(s) and
Receiver(s) to a local area network through a Router and/or Switch hub.
4 Connect each transmitter and receiver to power with the included power adapters.
5 Use the channel-selector tool to match the channel IDs on the Transmitter and Receiver (NOTE:
the devices will not connect automatically; they must be matched manually first).
6 To create a video wall, refer to the Video-wall Diagram section. Order your displays
accordingly and set the Display ID on the receivers to the corresponding positions.
One-to-many
2 2 2
1
3
3 3 3
3 3 3 3
3
3
1
2 2 2 2
1
2
3
4
4
Point-to-point
5
User Manual H.264 HDMI Over IP Video Wall Extender
Connect Devices
Hardware Installation
• Direct connect from Transmitter to Receiver unit.
• Transmitter unit to network switch to Receiver unit.
• Transmitter unit to an IGMP-snooping-enabled network switch to many Receiver units.
• Transmitter unit to network topology (must support IGMP snooping) to many Receiver units.
HDMI
HDMI
Cat5e/6
HDMI HDMI HDMI
HDMI HDMI
Cat5e/6 Cat5e/6 Cat5e/6 Cat5e/6
Cat5e/6 Cat5e/6
Cat5e/6
HDMI
1 1 1
3 3
2
3
3 3 3
3
33
3
3 3 3 3
2 2 2
2 2 2 2
Many-to-many
6
H.264 HDMI Over IP Video Wall Extender User Manual
• Many Transmitter units to an IGMP-snooping-enabled network switch to many Receiver units
• Many Transmitter units to network topology (must support IGMP snooping) to many Receiver units.
Video-wall Diagram
Display ID
12
3 4
5 6
7 8 9
A B C
D E F
Video-wall Diagram
0
HDMI HDMI HDMI
HDMI
Cat5e/6 Cat5e/6 Cat5e/6 Cat5e/6
Cat5e/6 Cat5e/6
Cat5e/6
HDMI
HDMI
Cat5e/6
Cat5e/6
Cat5e/6
Cat5e/6
HDMI HDMI
Max. distance up
to 500 m (1,640 ft.)
when cascading
with four switches
VESA 100 x 100
7
User Manual H.264 HDMI Over IP Video Wall Extender
VESA Mounting
CAUTION! Use only the included power adapters. Using other power adapters may damage your device.
IMPORTANT! Use the correct adapter plug for your area/region. This adapter is for dry and indoor uses only.
Installation Example
6 Done!5 Device connections
4 Select the RX Display ID
3 Select the TX / RX Channel ID
2 You’ll need these:1 Want to set up a 2x2 video wall?
Transmitter (1, #208338)
Network switch
Monitors (4)
Receiver (4, #208345)
8
H.264 HDMI Over IP Video Wall Extender User Manual
Management UI
In One-to-many or Many-to-many setups, the transmitters and receivers in the Intellinet Network Solutions
H.264 HDMI Over IP Video Wall Extender system can be conveniently managed through a Management User
Interface (UI). This UI lets users to create and adjust settings for the connected units, see important information
about them, create video walls and more. To log into the UI, use RJ45 cable to connect to the primary
network switch for all Transmitter and Receiver devices in the setup. See the example setup that follows.
Download the Management UI
Visit the product page at intellinet-network.com/barcode/208338 and click the DOWNLOADS for available
downloads. Click the icon titled INTVWEGUI.exe at the folder of the Management UI to launch the program.
Select Interface
Make sure your computer is on the the same local area network and select the network device named Realtek
PCIe GBE Family Controller. Click “OK”to continue.
Introduction to the Management UI
The management UI includes four pages:
• Device:see the full information of connected Receivers and Transmitters
• Walls:create a new video wall
• Management:select or switch the video source for each created video wall; drag and drop the
transmitters listed on the left to the video-wall setup shown on the right
• About: see publisher and UI version
INTVWEGUI
9
User Manual H.264 HDMI Over IP Video Wall Extender
Management UI - Device
See Receiver & Transmitter Information
The page shows the Device name, MAC address, Device ID and State of all Receivers and Transmitters. To edit
the Device name, select a Receiver or Transmitter device and click the Edit icon on the top right side of the page.
Advanced Device Settings
Right-click a device for these options: Reboot, Reset to default, Audio On/Off, Show ID and Upgrade firmware. A
device goes to the bottom of the list after it is rebooted. Show ID shows the information on the display.
Edit Device name
10
H.264 HDMI Over IP Video Wall Extender User Manual
Management UI - Walls
Create New Video Wall
Follow the steps to create a new video wall:
1 Click Create new wall and select the number of Rows and Columns. Then, edit the Wall name.
2 Click Show all receivers ID to easily identify which display is connected to each receiver.
3 Set the displays’positions using receiver IDs. Select and drag a receiver to the desired position.
4 Click Bezel correction and select the unit to adjust the widths of each side of the display (i.e., top, bottom, left
and right).
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Extensor de Intellinet
Intellinet
Intellinet 208260 Manual de usuario
Intellinet
Intellinet 561648 Manual de usuario
Intellinet
Intellinet 508957 Manual de usuario
Intellinet
Intellinet 525657 ISTREAM HD Manual de usuario
Intellinet
Intellinet 561952 Manual de usuario
Intellinet
Intellinet 207577 Manual de usuario
Intellinet
Intellinet 524353 Manual de usuario
Intellinet
Intellinet 524476 Manual de usuario
Intellinet
Intellinet IPE-2G60 Manual de usuario
Intellinet
Intellinet 561617 Manual de usuario
