Intelligent Sensing Anywhere CLOG500 Manual de usuario

CLOG500

User Manual

ISA – Intelligent Sensing Anywhere

Rua Pedro Nunes, Edifício D

3030-199 Coimbra, Portugal

Phone: +351 239 791 090

Fax: +351 239 791 099

Email: [email protected]

http://www.isasensing.com

CLOG500

CLOG500 User Manual i

Data Versão Descrição Autor

16/07/2014 V0.01 First release of document. Artur Vieira

03/09/2014 V0.02

Added option for variant EXC5_20XY

possibilitie to have possibilitie to have 2

sensors.

Artur Vieira

18/09/2014 V1.0 Revision Ester Soares

27/01/2015 V1.01 Changes for FCC certification Artur Vieira

02/03/2015 V2.00 Revision Ester Soares

CLOG500

CLOG500 User Manual ii

Índice

1General Information.................................................................................................................................................1

1.1 CLOG500 Model Numbering.....................................................................................................................1

2FCC PART 15 compliance......................................................................................................................................2

2.1 RF Exposure Information.............................................................................................................................3

3Warnings.......................................................................................................................................................................3

4Maintenance................................................................................................................................................................4

5Typical Installation procedure.............................................................................................................................4

6Sensor connection....................................................................................................................................................5

6.1 CLOG500 supplied with external cable................................................................................................6

7Placing the CLOG500.............................................................................................................................................6

7.1 Attaching the CLOG500..............................................................................................................................6

7.1.1 Using glue to attach.........................................................................................................................7

7.1.2 Using cable ties to attach..............................................................................................................9

7.2 Possible scenarios........................................................................................................................................10

8Equipment activation...........................................................................................................................................11

8.1 Passing the magnet to activate............................................................................................................11

8.2 Visual Indicators...........................................................................................................................................11

8.3 Equipment information.............................................................................................................................13

9CLOG500 configuration......................................................................................................................................13

9.1 Sensor types and input numbers.........................................................................................................13

9.1.1 Sensors connect through radio device.................................................................................14

10 Tips and Tricks........................................................................................................................................................14

CLOG500

CLOG500 User Manual 1

1General Information

The CLOG500 is a multi-purpose autonomous (GSM/CDMA/GPRS based, battery powered)

remote management system providing data logging, automatic meter reading and alarms,

certified to be used under potential explosive atmospheres.

Collected and stored data is sent to a central server via GSM, through SMS or TCP, with a

configurable frequency from several times a day to one time per week. This data can be

requested by any cell phone using SMS.

The system’s supply is obtained through a long life lithium battery which guarantees great

autonomy and easiness in installation.

1.1CLOG500 Model Numbering

aaC5_xxyz

aa EX = Equipment for Hazardous location (Certified

for ATEX, IECEx, USA and Canada)

Blank = Generic use equipment

xx1

00 = 3 Inputs (software selectable from analogue or digital)

10 = 2 analog inputs

11 = 1 analog input and 1 digital input

20 = 2 Analog Inputs

30 = 3 Digital Inputs

40 = 1 analog Input and 1 digital input

90 = 1 current (0-20mA) input.2

Y30 = No modem 3 = 2G Modem 4 = CDMA 1xRTT

modem

7 = 2G + GPS

modem

z 0 = No ISM Band Transceiver 1 = with ISM Band transceiver

CLOG500

CLOG500 User Manual 2

1Check the safety manual for input parameters.

2This model does not have hazardous location.

2FCC PART 15 compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: "How to Identify and

Resolve Radio-TV Interference Problems." This booklet is available from the U.S.

Government Printing Office, Washington D.C. 20402.

CLOG500

CLOG500 User Manual 3

WARNING: Changes and Modifications not expressly approved by the manufacturer or

registrant of this equipment can void your authority to operate this equipment under

Federal Communications Commission’s rules.

2.1RF Exposure Information

This device meets government’s requirements for exposure to radio waves.

This device is designed and manufactured not to exceed the emission limits for exposure to

radio frequency (RF) energy set by the Federal Communications Commission of U.S.

Government.

The device complies with FCC radiation limits set forth for an uncontrolled environment. In

order to avoid the possibility of exceeding the FCC radio frequency exposures limits, human

proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

3Warnings

PLEASE READ CAREFULLY BEFORE ANY MANIPULATION OF THE EQUIPMENT.

Reading of this manual and safety manual is mandatory prior to any manipulation

of the equipment. Failure to comply with presented safety instructions may lead to

severe damage or injury and loss of liability by the manufacturer.

These instructions must be kept and followed throughout the life of the equipment.

Never open the equipment when a potential explosive atmosphere may be present.

POTENTIAL ELECTROSTATIC CHARGING HAZARD. CLEAN ONLY WITH DAMP

CLOTHS.

Only use approved batteries.

Check other warnings in this manual (always marked with ).

CLOG500

CLOG500 User Manual 4

4Maintenance

The equipment will have no maintenance inside the safety zone. The maintenance

possible to perform on the field is just the batteries exchange and SIM Card

replacement. For others problems the equipment must be returned to

manufacturer.

5Typical Installation procedure

This procedure is valid for versions that contain a GSM or CDMA modem.

For version that only contains the ISM Band transceiver the only necessary steps are the

sensor connection, equipment placement and activation.

1) Connect the sensor to the CLOG500 (see section 6). Some models may already have this

connection.

2) Position the equipment next to the target (gas tank gauge, pulse meter, etc) and attach

it using the base of the equipment (see section 7).

3) Attach the sensor to the target.

4) Prepare the SMS to send to the equipment (see section Error! Reference source not

found.).

5) Activate the CLOG500, passing the magnet in order to prepare it to receive the SMS

configuration (see section 8.1). In some models it may be possible that you need to

operate the ON/OFF switch in order to activate the CLOG500 (see section 8).

a) Check if a red LED starts to flash inside the CLOG500.

b) After 2 minutes a green LED should turn ON and, after 30 seconds, start to flash.

This means that the modem is already registered on the GSM network (ready for the

SMS).

6) Send the SMS to the CLOG500 (see section Error! Reference source not found.).

7) Wait for the response from the CLOG500 (see section Error! Reference source not

found.).

CLOG500

CLOG500 User Manual 5

8) Check if the values for the ‘SQ:’ and ‘MEM:’ are correct (see section Error! Reference

source not found.).

9) Check if the value for the cabled channel is identical to the one shown by the respective

sensor. A 4%~ 6% errors is admissible.

10) Take note of the installation data on a sheet (see section Error! Reference source not

found.).

11) Take all the waste with you.

12) Congratulations, the installation is complete.

6Sensor connection

The only external component connected to the equipment may be a Rochester6320S level

sensor (max length= 3 m), or any sensor / digital switch which are compatible with the

equipment.

The sensor must already have the correct plug to connect to the CLOG500. The sensor

connector is illustrated in the following picture:

Figure 1 - Sensor connector location.

Attention: The sensor connector has a correct position for the cable insertion.

CLOG500

CLOG500 User Manual 6

Figure 2 – CLOG500 with sensor connected.

6.1CLOG500 supplied with external cable

The equipment may be supplied with external cable for sensor connection. The connection

between the equipment and the sensor should be made using a junction box.

Check Installation and safety manual for cable color code and safety parameters.

7Placing the CLOG500

7.1Attaching the CLOG500

The equipment should be attached to a solid surface (1m to 2m from the ground) with a

vertical orientation (if possible) optimized for radio transmission and communication.

To attach the equipment, it is recommended to use glue to fix the enclosure to the tank or

use cable ties. The next Figure shows an example of how to correctly attach the CLOG500

to a gas tank hook with cable ties or glue.

CLOG500

CLOG500 User Manual 7

Figure 3 – Example of correct attaching on a gas tank hook with cable ties or glue.

Some provided or recommended accessories:

Figure 4 - Cable ties. Figure 5 - Wurth MS Instant (Ref:

0893226100) Figure 6 –C leaner product - Wurth

Brake Cleaner (Ref: 08901087)

7.1.1 Using glue to attach

1. In case of fixation by glue, the user should clean the tank surface to remove dirt and

degrease from the area where is going to apply glue:

Tabla de contenidos

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario