Intelligent network solutions TSM100-K Manual de usuario

Man-1527 Rev.01

TSM100-K Quick Start Guide

Intelligent Network Solutions

TSM100-K

Quick Start Guide

*Man-1527*

Man-1527 Rev.01

TSM100-K Quick Start Guide

Safety

Suppliers of articles for use at work are required under section 6 of the Health and Safety at Work Act 1974 to ensure

as reasonably as is practical that the article will be safe and without risk to health when properly used.

An article is not regarded as properly used if it is used ‘without regard to any relevant information or advice’ relating

to its use made available by the supplier.

This product should be installed, commissioned and maintained by trained service personnel in accordance with the

following:

(i) Regulations for electrical equipment in buildings specific to the country of use.

(ii) Codes of practice

(iii) Statutory requirements

(iv) Any instructions advised by the manufacturer.

According to the provisions of the Act you are therefore requested to take such steps as are necessary to ensure

that you make any appropriate information about this product available to anyone concerned with its use.

Suppliers of articles for use at work are required under section 6 of the Health and Safety at Work Act 1974 to ensure

as reasonably as is practical that the article will be safe and without risk to health when properly used.

An article is not regarded as properly used if it is used ‘without regard to any relevant information or advice’ relating

to its use made available by the supplier.

This product should be installed, commissioned and maintained by trained service personnel in accordance with the

following:

(i) IEE regulations for electrical equipment in buildings

(ii) Codes of practice

(iii) Statutory requirements

(iv) Any instructions specifically advised by the manufacturer

According to the provisions of the Act you are therefore requested to take such steps as are necessary to ensure

that you make any appropriate information about this product available to anyone concerned with its use.

This equipment is designed to operate from 115V AC to 230V AC 50/60Hz mains supplies and is of class 1 con-

struction. As such it must be connected to a protective earthing conductor in the fixed wiring of the installation and

a readily accessible double pole disconnect device meeting the requirements of EN60950/IEC950 which discon-

nects live and neutral simultaneously shall be incorporated in the fixed wiring.

Switch disconnect devices such as MK Sentry 63A or similar are suitable for this. Failure to ensure that all conduc-

tive accessible parts of this equipment are adequately bonded to the protective earth will render the equipment un-

safe.

This Control Panel is environmental class A and is designed for indoor use only at temperatures between -10°C and

+45°C with a maximum relative humidity of 95%. The IP rating for the enclosure is IP30.

Operation outside of these limits may render the equipment unsafe.

Man-1527 Rev.01

iNS TSM-100K Quick Start Guide

TSM-100K (INS007) Quick Start Guide

This Start Guide provides module connection/settings overview and links to the product User Guide.

QR Codes

The QR codes below provide links to INS User Manuals. Using your Smartphone, tablet or device (where necessary)

install a third party QR Code Reader and scan the code to open the documents.

Figure A-1

Reading the QR Codes

Should you be unable to work with QR codes Manuals can be obtained by visiting the following website pages:

Important! Information in this Start Guide is supplementary.

The product Installation Manual and Operation Manual should read, understood and referred to throughout.

TSM-100K (INS007)

User Manual

Manual Variant Website

TSM100-K User Manual http://www.kentec.co.uk/manuals/man-1493.pdf

Man-1527 Rev.01

iNS TSM-100K Quick Start Guide

Figure A-2

Remote FAP LAN interface Connections

Man-1527 Rev.01

iNS TSM-100K Quick Start Guide

Terms and Conditions

Details of Kentec Electronics Ltd. Terms and Conditions including Warranties and Returns & Repair Policies can be

found on our website at the following locations:

Address of Kentec Electronics Ltd.

Units 25-26 Fawkes Avenue,

Questor, Dartford,

Kent. DA1 1JQ

United Kingdom

Registered in England

No.1937570

Tel: +44 (0)1322 222121

http://www.kentec.co.uk

Disclaimer

In no event shall The Manufacturer be liable for any damages or injury of any nature or kind, no matter how caused, that arise from

the use of the equipment referred to in this manual. Strict compliance with the safety procedures set out and referred to in this

manual, and extreme care in the handling or use of the equipment, are essential to avoid or minimise the chance of personal injury

or damage to the equipment. The information, figures, illustrations, tables, specifications, and schematics contained in this manual

are believed to be correct and accurate as at the date of publication or revision. However, no representation or warranty with re-

spect to such correctness or accuracy is given or implied and The Manufacturer will not, under any circumstances, be liable to any

person or corporation for any loss or damages incurred in connection with the use of this manual.

The information, figures, illustrations, tables, specifications, and schematics contained in this manual are subject to change without

notice. Unauthorised modifications to the fire detection system or its installation are not permitted, as these may give rise to unac-

ceptable health and safety hazards. By installing this equipment on a computer network, the owner accepts full and unequivocal

responsibility for ensuring that it is protected against all cyber threats and illegal tampering during the lifetime of the equipment.

Any software forming part of this equipment should be used only for the purposes for which The Company supplied it. The user

shall undertake no changes, modifications, conversions, translations into another computer language, or copies (except for a nec-

essary backup copy). In no event shall The Manufacturer be liable for any equipment malfunction or damages whatsoever, includ-

ing (without limitation) incidental, direct, indirect, special, and consequential damages, damages for loss of business profits,

business interruption, loss of business information, or other pecuniary loss, resulting from any violation of the above prohibitions.

Terms, Conditions & Warranty https://kentec.co.uk/terms-and-conditions/

Returns & Repairs http://www.kentec.co.uk/returns-and-repairs/

Man-1527 Rev.01

iNS TSM-100K Quick Start Guide

Notes:

.....................................................................................................................................................................................

Tabla de contenidos

Otros manuales de Cambiar de Intelligent network solutions

Intelligent network solutions

Intelligent network solutions 561112 Manual de usuario

Intelligent network solutions

Intelligent network solutions DNX-A-2R-K Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario