Intelitek ViewFlex Manual de usuario

ViewFlex Camera

ASSEMBLY INSTRUCTIONS

Catalog # 101971 Rev. B

April 2019

ViewFlex CameraAssembly Instructions

Cat # 101971 Rev. B

April 2019

way, includingbutnot limited to photocopy, photography, magnetic, orotherrecording, without the

prioragreement and written permission of the publisher. Program listings may be entered, stored, and

executed in a computersystem, but not reproduced for publication.

Every effort hasbeen made to make this guide complete and as accurate as possible. However, no

warranty of suitability, purpose orfitness is made or implied. Intelitek Inc. is not liable or responsibleto

any person orentity for loss or damage in connection with orstemming from the use of the software,

equipment and/or the information contained in this publication.

Intelitek Inc. bears no responsibility forerrors which may appearin this publication and retains the right

to make changes to the software, equipment and manual without prior notice.

Intelitek Inc.

Toll Free: 800-221-2763

Phone: 603-625-8600

Fax: 603-437-2137

Email: info@intelitek.com

Intelitek software and documentation are availableat http://intelitekdownloads.com.

Contents

1. Assembling the Camera Stand .............................................................................................................................................4

2. Wiring the Power ...................................................................................................................................................................6

3. Appendix: Breakout Cable Specifications ..........................................................................................................................7

This manual only details the assemblyand wiring instructions for your Cognex 2000 Vision Sensor. For

more information about the Cognex 2000 and its use, see the Cognex 2000 user manual. Visit

https://www.cognex.com/support for the most up-to-date software.

1. Assembling the Camera Stand

The camera stand forthe Cognex (#00-1430 -0000) is used to hold the Cognex Vision Sensor(QC

camera) in position in orderto carry out ViewFlexoperations. This section describes how to attach the

camera to the camera stand.

To assemble the camerastand:

1. Secure the base to a table.

▪On a slotted table, screw four M5 Allen screws through the base and into four M5 slot nuts

(shown below).

▪On a Formica table, secure the base directly to the table using four pan head Phillips screws.

▪If you are connecting the stand to a CIM track, use the angular connector with accompanying

bolts and nuts (catalog number 110633).

2. Attach the camera to the bracket using two M3 Phillips screws. Fasten the screws.

Note: You must ensure that the camera is secure once attached.

3. Connect the Ethernet cable (green) and the breakout cable (black) to the camera. Secure the

cables to the vertical beam with two cable clamps. The clamps should be secured with M5 flat

head Allen screws and T-slot nuts.

4. Secure the loose sections of the cables to the table using cable clamps and nylon cable ties. The

clamps should be secured to a slotted table with M5 flat head Allen screws and T-slot nuts, and

to a Formica table with pan head Phillips screws.

2. Wiring the Power Connections

You Cognex vision sensor’s breakout cable requires connection to a 24VDC adapterbefore it can be

connected to the power supply unit.

Note: For this procedure, you require a small flat-head screwdriver.

To wire the breakout cable:

1. Locate and separate the black and red wires at the end of the breakout cable. The black wire is

the ground connection and the red wire is the +24VDC connection. For information about the

other wires in the breakout cable, see the appendix.

2. Connect the black and red wires to the adapter, using the screwdriver to secure the wires:

▪Connect the black wire to the adapter’s (-) slot.

▪Connect the red wire to the adapter’s (+) slot.

Note: Unused wires can be clipped short or tied back using a tie made of non-conductive

material. Keep all bare wires separated from the +24VDC wire.

3. Connect the adapter to the power supply.

4. Connect the power supply to a wall adapter.

5. Ensure that the vision sensor’s green power LED is lit.

3. Appendix: Breakout Cable Specifications

Besides providing connections to an external power supply, the breakout cable provides connections to

the acquisition trigger input, a general purposeinput, high-speed outputs, and RS-232serial

communications. The table below lists the connections.

Wire Color

Signal Name

Yellow

HS OUT 2

White/Yellow

RS-232 Tx1

Brown

RS-232 Rx1

White/Brown

HS OUT 3

Violet

In 0

White/Violet

INPUT COMMON

Red

+24VDC

Black

GND

Green

OUTPUT COMMON

Orange

Trigger

Blue

HS OUT 0

Grey

HS OUT 1

1If hardware handshaking is required, an I/O module mustbe used.

Tabla de contenidos

Otros manuales de Cámara digital de Intelitek

Intelitek

Intelitek ViewFlex Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario