Intelbras Smart TX 4020 Manual de usuario

User manual

TX 4020 Smart

English

TX 4020 Smart

Universal transmitter

Congratulations, you have just purchased a product with Intelbras quality and safety.

The TX 4020 Smart universal transmitter was developed to facilitate the installation of wired sensors in your daily life, as

it allows a wired sensor to communicate wirelessly with the alarm center. With digital and SMD assembly technology, it is

compatible with all Intelbras wired sensors and the majority of wired sensors available on the market.Works in FSK or OOK

modulation. Carefully read the information in this manual for correct use of the transmitter.

Care and safety

» LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or carry out any type of processing of

personal data using this product.

» This product is intended for indoor and semi-open environments.

» Avoid installing the transmitter directly under metal surfaces to avoid changes in its operating characteristics.

» Please conrm that the installation location is stable and appropriate.

» Wireless communication technology, when exposed to environments with high power radiation, may suffer interference

and have its performance impaired, for example: locations close to TV towers, AM/FM radio stations, amateur radio

stations, etc.

» Do not expose the TX 4020 Smart magnetic sensor directly to sunlight, rain and humidity.

» For your safety, test the product and systems at least once a week. This is necessary due to changing environmental

conditions, electrical or electronic outages, and tampering. Take all necessary precautions for the safety and security of

your property.

Summary

1. Technical specications 5

2. Features 5

3. Product 6

4. Sensor opening 6

5. Registering the TX 4020 Smart transmitter 7

6. TX 4020 Smart transmitter supervision adjustment 7

7. Installation 8

7.1. Connection between TX 4020 Smart and wired sensor ...............................................9

7.2. Application ...............................................................................9

8. Battery 10

9. Test 10

10. Homologation 10

Warranty term 11

1. Technical specications

Operating voltage 3 V Lithium battery, model CR2032

RF Range 100 meters without barrier

Transmission frequency 433.92 MHz

Modulation Supervised (FSK) or unsupervised (OOK)

OOK baud rate 2 KBps (open source)

Anti jamming Against external interference

Installation environment Internal and semi-open

Operating Temperature -10°C to 50°C

Transmitter dimensions (W × H × D) 40×49.7×20.8 mm

2. Features

» Low battery indication;

» Easy installation;

» Key for registration;

» Supervised (FSK) or unsupervised (OOK);

» Long-lasting lithium battery;

» Transmission frequency 433.92 MHz.

3. Product

LD1

1. Transmitter cover

2. Light conductor (LED)

3. Base

4. Screw hole for xing

5. Battery contact

6. Registration button

7. Jumper (OOK/FSK)

8. Cable connector

4. Sensor opening

To access the TX 4020 Smart board for registration and battery replacement, simply push the hole and remove the cover.

This way the plate will be exposed and ready for handling.

Orifício para

abertura

Opening lid

Remove the board, then insert the battery (model CR2032), respecting polarity.

LD1

CR2032

5. Registering the TX 4020 Smart transmitter

To register the TX 4020 Smart transmitter code in the alarm center, follow the procedure below:

Insert the LITHIUM 3 Vcc - CR 2032 battery, then enter the command to register the wireless device in the alarm center

that will be used (Check the procedure in the alarm center manual).Then press the CH1 key for approximately 2s, observing

whether the LED lights up, if the LED lights up it indicates that transmission has occurred, if it does not light up, check the

battery and repeat the procedure.

Note:

to register using the CH1 key, the transmitter must not be connected to the wired sensor. If the transmitter is already

connected to a wired sensor, simply trigger the sensor and observe whether the transmitter LED lights up, if the LED lights

up it indicates that there has been a transmission, if it does not light up, check the connection between the sensor and the

transmitter or check the battery and repeat the procedure.

» Low battery sensor: the TX 4020 Smart has a battery level meter, which measures the voltage and noties you of the

best time to change it. If the alarm center is Intelbras, the sensor low battery warning will be indicated on the product

panel. The sensor sends a low battery warning in both OOK and FSK modulations.

6. TX 4020 Smart transmitter supervision adjustment

The TX 4020 Smart transmitter allows you to select between supervised (FSK) and unsupervised (OOK) modes. To switch

between supervision modes, simply remove the battery from the transmitter, open the OOK/FSK jumper indicated on the

board (and then replace the battery); once this is done, the transmitter will operate in supervised mode (FSK). Changing

from supervised mode (FSK) to unsupervised mode (OOK) is also simple, just remove the battery from the transmitter, close

the OOK/FSK jumper terminals again and replace the battery, once this is done the transmitter will return to operating in

the unsupervised mode (OOK). Factory default: unattended (OOK).

In FSK modulation, the transmitter transmits opening and closing and periodically performs supervision.

LD1

OOK / FSK

Com Jumper

OOK

Sem Jumper

FSK

With Jumper OOK Without FSK Jumper

7. Installation

The TX 4020 Smart transmitter can be xed using double-sided tape or a screw. If the option with double-sided tape is

chosen, clean the surface that will be in direct contact with the tape and then stick it to the base of the product. If you are

going to use screws, simply open the transmitter and use the holes for the screw located on the base of the product, as

shown in the following gure.

Instalação com parafuso Instalação com fita dupla face

Fita

Screw installation Installation with double-sided tape

To close the transmitter, position the cover on the base and press where the latches are located.

Trava

Lock

7.1. Connection between TX 4020 Smart and wired sensor

Use an external source to power the wired sensor, then connect the alarm output cable (normally closed (NC)) of the wired

sensor to the TX 4020 Smart universal transmitter terminal, as shown in the following gure:

LD1

TX 4020 SMART

SENSOR COM FIO

FONTE

ALARME

TX 4020 Smart

Wired sensor

Power

Alarm

Maximum distance 1 m

The maximum recommended wiring distance for installation between the TX 4020 Smart and the sensor connected to

it is 1 meter.

Note: the ohmic resistance of the cable is very low for this distance, so you can use a cable of your choice. Once this is

done, install the TX 4020 Smart transmitter in a location where it is fully protected against sunlight, rain and humidity.

7.2. Application

Central de alarme ou

receptor de RF

SENSOR DETECTANDO

TX 4020 SMART TRANSMITINDO

STATUS DO SENSOR

Sensor detecting

External source

Alarm center or RF

receiver

TX 4020 Smart transmitting

Sensor Status

8. Battery

Use only quality batteries, with the correct size for the device. The battery model must be CR2032, using one (1) battery

per transmitter.

This product has an internal battery. After their useful life, the batteries must be delivered to an authorized technical assistance

service provided by Intelbras or directly disposed of in an environmentally appropriate manner, avoiding environmental and health

impacts. If you prefer, the battery as well as other unused Intelbras brand electronics can be disposed of at any Green Eletron

collection point (electronic waste manager to which we are associated). In case of doubt about the reverse logistics process, please

contact us at (48) 2106-0006 or 0800 704 2767 (from Monday to Friday from 8 am to 8 pm and on Saturdays from 8 am to 6 pm)

or by e-mail. -mail suppor[email protected].

9. Test

Once installed and in operation, check whether the alarm center is receiving triggering information from the wired sensor

installed on the TX 4020 Smart. If any failure occurs, it is necessary to reposition the transmitter or the alarm center. Make

sure to take all precautions and follow the installation recommendations to obtain the best operating performance of the

product.

10. Homologation

This equipment is not entitled to protection against harmful interference and may not cause interference to duly authorized

systems. For more information on the approved product, visit the website:

https://www.gov.br/anatel/pt-br.

Tabla de contenidos

Otros manuales de Transmisor de Intelbras

Intelbras

Intelbras TX 8000 Manual de usuario

Intelbras

Intelbras TX 4020 Smart Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario