Intel SPKA4 - Server Platform - 0 MB RAM Manual de funcionamiento
SKA4/SPKA4 Important Information
Service Partition
The service partition is a special hard disk partition. It is established when you initially set
up the server system and contains utilities, diagnostics, and other software required for
remote management. The service partition is not marked as an active partition and the
server will only boot from it by a special request. It is not normally visible to the server
user because it has a special non-standard partition type that does not appear as an
accessible file system to the end user operating system. However, low level disk utilities
can see the partition entry as an unknown type, and recognize its space.
The utilities and diagnostics on the service partition can be run locally or remotely. In
order to run the utilities and diagnostics the server must boot from the service partition.
Remote execution is available from the Direct Platform Control (DPC) Console Manager
and System Setup Utility (SSU) Client.
For complete installation instructions, see the Installation Guide for the Intel®Server
Control (747116-00x). We recommend you install the service partition before
installing an OS.
Brief Instructions to Install the Service Partition
1. Boot to the Software Kit CD.
2. When the Server Board CD-ROM menu appears, use the arrow keys to select the
Utilities menu and press Enter.
3. Select Run Service Partition Administrator and press Enter.
4. Choose item 3 - Create service partition (first time).
5. Follow the instructions on your screen to select the hard drive for service partition
installation.
6. Reboot to the Software Kit CD.
7. When the Server Board CD-ROM menu appears, use the arrow keys to select the
Utilities menu and press Enter.
8. Select Run Service Partition Administrator and press Enter.
9. Choose item 4 - Format service partition and install software.
10. Follow the instructions on the screen to format the service partition and install the
partition software.
A12462-001
2 SKA4/SPKA4 Important Information
Memory Requirements
All four sockets of a DIMM bank must be populated for the server to boot. Refer to the
SKA4 Baseboard Product Guide for more information.
Voltage Regulation Modules
The board contains voltage regulation circuitry for the primary processor. If you install
additional processors, you must install a Voltage Regulation Module (VRM) for each
additional processor. Refer to the SKA4 Baseboard Product Guide for more information.
Power Cord
There is a notch in the handle of the power supply to relieve stress on the power cord.
Refer to the SPKA4 MP Server System Product Guide for more information.
POST Information
If you press the <Esc> key at any time during the POST, a menu will appear after the
POST completes. From this menu you can specify which device to boot from or you can
enter Setup.
Using the CD
Accessing Manuals
To read the manuals on the CD, you must insert the CD into a system that is running
Windows†.
1. If the CD does not automatically start, run the menu.exe program.
2. Click on “Featured Products” in the sidebar.
3. Select a product from the “select a product” pull down menu
4. Use the “view additional documentation” or “print additional documentation” menus to
access the product guides.
Booting from the CD
There are two ways to boot from the CD. The first is to press <Esc> during the POST and
select it from the menu. The second is to enter Setup and change the boot priorities. Refer
to the SKA4 Baseboard Product Guide for more information.
3
Getting Help on the Web
The following site has information and downloads for your system:
http://support.intel.com
The following sites have information and downloads for your system, but are password
protected. Please contact your service representative to gain access to these sites.
http://channel.intel.com
http://www.intel.com/go/serverbuilder
http://www.intel.com/ibl
Disclaimer
Information in this document is provided in connection with Intel®products. No license, express or
implied, by estoppel or otherwise, to any intellectual property rights is granted by this document.
Except as provided in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability
whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel
products including liability or warranties relating to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual property right. Intel products are not
designed, intended or authorized for use in any medical, life saving, or life sustaining applications or
for any other application in which the failure of the Intel product could create a situation where
personal injury or death may occur. Intel may make changes to specifications and product
descriptions at any time, without notice.
†Third party brands and names are property of their respective owners.
Copyright 1999, 2000 Intel Corporation. All rights reserved.
4 SKA4/SPKA4 Important Information
Otros manuales para SPKA4 - Server Platform - 0 MB RAM
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa de servidor de Intel
Intel
Intel BB5520UR Guía de configuración
Intel
Intel SE7221BA1-E Manual de usuario
Intel
Intel S3000AH Guía de configuración
Intel
Intel SDS2 Manual de usuario
Intel
Intel S875WP1 - EATX MBD 875 P4 DDR-2CH SATA RAID VID... Manual de usuario
Intel
Intel S5000XAL Guía de configuración
Intel
Intel S1200RP Manual de usuario
Intel
Intel A67054-002 Manual de usuario
Intel
Intel SE7221BK1-E - Server Board - Mainboard Guía de configuración
Intel
Intel S5000PAL Manual de usuario
Intel
Intel S5500BC Manual de usuario
Intel
Intel SE7520AF2 Manual de usuario
Intel
Intel S2600CW Guía de configuración
Intel
Intel SCB2ATA Manual de usuario
Intel
Intel SE7520BD2 Guía de configuración
Intel
Intel SE7501CW2 Manual de usuario
Intel
Intel S5000XAL Manual de usuario
Intel
Intel S2600CP Family Manual de usuario
Intel
Intel D50TNP Manual de usuario
Intel
Intel S5000PAL Guía de configuración
