Intel PT-6IBD Manual de usuario

PT-6IBD

PT-6IZP

PT-6IBP

ATX MAINBOARD

( VER. 3.x )

USER’S MANUAL

DOC. NO. UM-IBD-E5 ...................................................................PRINTED IN TAIWAN

440BX MAINBOARD TABLE OF CONTENTS

TABLE OF CONTENTS

Chapter & Section Page

1. INTRODUCTION ...............................................................................1-1

1.1 OVERVIEW ............................................................................................. 1-1

1.2 MAINBOARD LAYOUT ....................................................................... 1-2

1.3 SPECIFICATIONS.................................................................................. 1-3

2. INSTALLATION ................................................................................2-1

2.1 UNPACKING ........................................................................................... 2-1

2.2 AMAZING WAYS TO POWER ON THE PC SYSTEM.................... 2-2

2.3 POWER OFF THE PC SYSTEM .......................................................... 2-4

3. HARDWARE SETUP........................................................................3-1

3.1 INSTALLATION OF CPU ..................................................................... 3-1

3.2 INSTALLING THE DRAM MODULES ........................................... 3-1

3.3 CONNECTORS........................................................................................ 3-4

3.4 JUMPERS................................................................................................. 3-16

3.5 HOW TO SELECT THE CPU SPEED ................................................. 3-20

3.6 INSTALLATION OF DEVICE DRIVERS........................................... 3-23

4. AWARD BIOS SETUP .....................................................................4-1

4.1 GETTING STARTED ............................................................................ 4-1

4.2 MAIN MENU .......................................................................................... 4-2

4.3 CONTROL KEYS................................................................................... 4-2

4.4 STANDARD CMOS SETUP................................................................. 4-3

4.5 BIOS FEATURES SETUP.................................................................... 4-4

4.6 CHIPSET FEATURES SETUP............................................................ 4-6

4.7 POWER MANAGEMENT SETUP ..................................................... 4-11

4.8 INTEGRATED PERIPHERALS .......................................................... 4-16

4.9 PNP/PCI CONFIGURATION............................................................... 4-19

4.10 LOAD SETUP DEFAULTS ................................................................ 4-23

4.11 SUPERVISOR PASSWORD / USER PASSWORD....................... 4-24

4.12 USER PASSWORD............................................................................... 4-25

4.13 IDE HDD AUTO DETECTION ........................................................ 4-27

4.14 SAVE & EXIT SETUP / EXIT WITHOUT SAVING ....................... 4-28

440BX MAINBOARD

SOMETHING IMPORTANT !

¶TRADEMARKS

All trademarks used in this manual are the property of their respective owners.

¶LOAD SETUP DEFAULTS

“LOAD SETUP DEFAULTS” is the function which will have the BIOS default

settings loaded into the CMOS memory, these default settings are the best-case

values which will optimize system performance and increase system stability This

function will be necessitated when you receive this mainboard, or when the system

CMOS data is corrupted. Please refer to the Section 4.8 for the procedures.

¶DISCHARAGE CMOS DATA

Whenever you want to discharge the CMOS data or open the system chassis, Make

sure to disconnect the AC power first because there is always the 5V standby voltage

connected to the ATX form-factor mainboard. Without disconnecting the AC power

connector from the PC system, the mainboard can be damaged by any improper

action .

¶WAKE ON LAN

In order to support the Wake On LAN feature, the system requires a special SPS

(Switching Power Supply), Such power supply must be able to provide at least 700

mA of driving capability on the “5V standby” voltage. Please refer to the Section 3.3

for pin assignment.

¶WARNING !

The "Static Electricity" may cause damage to the components on the mainboard, In

order to avoid the damage to the mainboard accidentally, please discharge all static

electricity from your body before touching this mainboard.

¶NOTICE

Information presented in this manual has been carefully checked for reliability;

however, no responsibility is assumed for inaccuracies. The information contained in

this manual is subject to change without notice.

440BX MAINBOARD INTRODUCTION

1-1

1. INTRODUCTION

1.1 OVERVIEW

This Mainboard is a high performance personal computer mainboard. It is a Slot1,

ATX form-factor mainboard with the Intel® 82440BX/ZX AGPset™ and

Winbond® I/O chipset. There are the A.G.P. (Accelerated Graphics Port) and PCI

Local Bus on the mainboard.. It is designed for 233MHz, 266MHz, 300 MHz,

333MHz, 350MHz, 366 MHz ,400MHz, 433MHz, 450MHz, 466MHz and

500MHz high performance Pentium™ II and Celeron™ (S.E.C. Cartridge)

processors

This mainboard is designed by using the Intel®82440BX or 82440ZX AGPset™

system chipset. When different chipset is installed on the board, the feature of the

following mainboards will have different feature as following:

Model Name Chipset PCI Slot DIMM Socket ECC

PT-6IBD BX 5 4 YES

PT-6IBP BX 5 3 YES

PT-6IZP ZX 4 2 NO

This mainboard has built-in two channel “PIO” and “Ultra DMA/33 Bus Master”

mode PCI IDE ports, one Floppy Disk control port, two high speed Serial ports

(UARTs) and one multi-mode Parallel port and supports PS/2™ mouse, IR and

USB ports. It is designed to support the high performance Pentium™ II and

Celeron™ processors for the high-end and true GREEN-PC computer systems.

Pentium™ II and Celeron™ are the 64-bit processors with RISC technology,

which offers several key features such as built-in 512K/128K L2 cache, 12-stage

super-pipeline architecture, out of order execution …. etc. In order to optimize of

its capabilities and performances, the 32-bit Operating System (such as

Windows® NT and OS/2™) and 32-bit applications are recommended.

440BX MAINBOARD INTRODUCTION

1-2

1.2 MAINBOARD LAYOUT

PCISLOT

USB

PCISLOT

BAT1

SLOT1

SPKR

AGPSLOT

ISASLOT

PCISLOT

CN1

CN10IDE1

CN3,CN6,CN7

CN2

CN9IDE2

CN11FDC

CN4

BIOS

KBLOCK

CN1

CPUFAN

CN14

PCISLOT

JP100

JP1

U17

440BX MAINBOARD INTRODUCTION

1-3

1.3 SPECIFICATIONS

¥CPU

Intel® Pentium™ II or Celeron™ processor 233, 266, 300, 333. 350, 366, 400,

433, 450, 466 and up to 500MHz.

¥CPU VCC

Switching Voltage Regulator circuits on board, supports +1.80V DC through

+3.5V DC CPU Core Voltage.

Note : The CPU Core Voltage will be Detected and adjusted automatically by the

VID-pin on the CPU, so there is no manual-adjustment required to select the CPU

voltage. Simply plug in the CPU and start immediately.

¥WORD SIZE

Data Path : 8-bit, 16-bit, 32-bit, 64-bit

Address Path : 32-bit

¥PC SYSTEM CHIPSET

PT-6IBD, PT-6IBP: Intel® 82440BX AGPset™ (82443BX, 82371EB)

PT-6IZP: Intel® 82440ZX AGPset™ (82443ZX, 82371EB)

¥SUPER I/O CHIPSET

Winbond® W83977TF-AW

¥FRONT SIDE BUS FREQUENCY

66 MHz and 100MHz selectable.

¥MEMORY

PT-6IBD: Four 168-pin DIMM sockets, Maximum 512 MB with ECC.

PT-6IBP: Three 168-pin DIMM sockets, Maximum 384 MB with ECC.

PT-6IZP: Two 168-pin DIMM sockets, Maximum 256 MB without ECC.

CACHE :512KB pipelined burst SRAM built-in Pentium™ II processor.

0KB or 128KB SRAM in Celeron™ processor.

¥BIOS

AWARD System BIOS. 128KB x 8 Flash ROM

(Supports Plug & Play, ACPI, DMI and Green functions).

440BX MAINBOARD INTRODUCTION

1-4

¥EXPANSION SLOTS

AGP Slots : One 32-bit AGP Slot (Supports 1x or 2x AGP graphics cards)

PCI Slots : Five 32bit PCI slots on BX mainboard (PT-6IBD and PT-6IBP).

Four 32bit PCI slots on ZX mainboard (PT-6IZP)

ISA Slots : 16-bit x 2 (One of the slot is PCI/ISA shared)

¥WOL PORTS

One WOL connector supports Wake-On-LAN (WOL up-designed)

¥SB-LINK PORTS

One SB-LINK feature connector to support PCI sound cards. (such as Creative™

Labs EMU8008 sound chip)

¥USB PORTS

Two Universal Serial Bus (USB) ports.

¥IDE PORTS

Two channels of Ultra DMA/33 Bus Master IDE ports, which will support up to 4

IDE devices like IDE hard disk, ATAPI CD-ROM and LS-120/ZIP-100 devices.

The IDE ports can be programmed to support PIO Mode 4, DMA mode 2 and Ultra

DMA/33.

¥SUPER I/O PORTS

1. Two high speed NS16C550 compatible serial ports (UARTs).

2. One parallel port, supports SPP/EPP/ECP mode.

3. One Floppy Disk Control port.

¥IR PORT

One HPSIR and ASKIR compatible IR transmission connector (5-pin).

One Consumer IR transmission connector (4-pin, optional).

¥MOUSE AND KEYBOARD

One PS/2™ mouse connector, One PS/2™ keyboard connector.

440BX MAINBOARD INTRODUCTION

1-5

¥HARDWARE MONITORING (optional)

Winbond W83783S (U17) is designed on the board to monitor hardware healthy

status like system voltage, system temperature, and cooling fans. For example,

when CPU temperature is too high, you will hear a series of beeping alarm and the

CPU speed will be slowing down to throttling speed. When you hear the beeping

alarm, you will have to turn the power off immediately and check on the mainboard

components to see whether it is working properly or not. If you don’t know how to

handle it, send the PC system to your dealer for technical support. In order to make

the hardware monitoring active, you will have to install the hardware monitoring

program as following procedure:

Step 1. Insert the mainboard CD into the CD ROM drive.

Step 2. Select "\Driver\mainboard\Hardware Monitoring\W83783S"

Step 3. Run "SETUP.EXE" to install the hardware monitoring program.

¥ACPI

Advanced Configuration and Power Interface (ACPI) function is strongly

recommended by PC’98 because it will let you have many additional features and

that will make your PC system becomes very friendly and convenient. Followings

are the ACPI features designed on the board:

1. On Now: power on the system by panel-switch, Keyboard, PS/2™ Mouse,

Modem ring-in, RTC alarm or LAN signal.

2. Power off (soft-off) by OS or Panel-switch.

3. CPU cooling fan auto-off during Suspend state.

4. Resuming of PC system. (such as Modem ring-in, RTC alarm, .... etc.)

5. Supports Full-On/Doze/Standby/Suspend operating modes.

¥DIMENSION

1. Width & Length : 305 mm x 190 mm.

2. Height : 2 1/2 inches with CPU Retention Mechanism.

3. PCB Thickness : 4 layers, 0.05 inches normal.

4. Weight : 18 ounces.

ENVIRONMENT LIMIT

1. Operating Temperature : 10to 40. (50to 104)

2. Required Airflow : 50 linear feet per minute across CPU.

3. Storage Temperature : - 40to 70. (- 40to 158)

4. Humidity : 0 to 90% non-condensing.

5. Altitude : 0 to 10,000 feet.

440BX MAINBOARD INSTALLATION

2-1

2. INSTALLATION

2.1 UNPACKING

The mainboard contains the following components. Please inspect the following

contents and confirm that everything is there in the package. If anything is missing or

damaged, call your supplier for instructions before proceeding.

lThis mainboard.

lOne USER‘S MANUAL.

lOne Cable set for IDE and Floppy devices.

lOne Pentium™ II Processor Retention Mechanism (RM).

lOne CD diskette for device driver and utility programs.

This mainboard contains electrostatic sensitive components and it can be easily

damaged by static electricity. So please leave it sealed in the original packing until

when installing.

A grounded anti-static mat is recommended when unpacking and installation. Please

also attached an anti static wristband to your wrist and have it grounded to the same

point as the anti-static mat.

After the opening of the mainboard carton, please observe the mainboard carefully to

make sure there is no shipping and handling damage before you can start to install the

PC system.

Having finished all the procedures above, you are now ready to install the mainboard to

the chassis. Please make sure that the chassis is the ATX type so that the mounting hole

will match with this mainboard.

440BX MAINBOARD INSTALLATION

2-2

2.2 AMAZING WAYS TO POWER ON THE PC SYSTEM

When the mainboard has been installed successfully, there are several ways to

power on the system. Please read the following description for all the details.

POWER BUTTON

The power button can be programmed by COMS setup program and it has different

features. Please refer to page 3-14 for detail function description.

Note: This power button can not be used to power-on the PC system if the

”Password“ is selected to power on your system. (please refer to Section 4.8 for

the “INTEGRATED PERIPHERALS“ in the CMOS setup.) However, you can

always use the power button to turn off the power.

¨KEYBOARD (PASSWORD OR HOT KEY)

This mainboard allows you to use your personal password or a combination of hot

key to power on your PC system. When the jumper setting on JP1 is “Enabled”, the

keyboard OnNow function will be activated. Under this circumstance, this

mainboard will keeps scanning the keyboard status waiting for the correct password

or hot key input even when the system power is off (the stand-by 5V is still working

and the power LED on the keyboard is still active). If you have selected the

Password to power on the PC system in the BIOS setup program, the only way to

power on the PC system will be the correct password. ( you can not use the power

button on the front panel to power on the PC system.) When you have selected the

keyboard hot key to power on the PC system, you will be able to use keyboard hot

key to power on the PC system. ( you can use the power button to power on the PC

system as well.) ( Please refer to Section 4.8.-PowerOn function)

When the “Password” and “Hot KEY” is selected, you will have to reboot the PC

system to activate the setting, when you see the POST (Power On Self Test) is

completed, the setting is changed and stored in the CMOS memory. Having finished

the procedure, you may turn the power off and then you can use the keyboard to

power-on the PC system afterward.

In case that you forget the “Password” or “Hot Key”, disconnect the AC power for

30-60 seconds then re-connect the AC power to the PC system, the power button

will be activated again and you can use the power button to turn on the system.

Input your personal password again in the BIOS setup program, and then you may

use the new password to power-on the PC system afterward.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Intel

Intel

Intel D845HV Manual de usuario

Intel

Intel D848PMB Manual de usuario

Intel

Intel DQ57TML Manual de usuario

Intel

Intel SBC-776 Manual de usuario

Intel

Intel DH61DL Manual de usuario

Intel

Intel LGA775 Manual de usuario

Intel

Intel DH67CF Manual de usuario

Intel

Intel D850GB Manual de usuario

Intel

Intel S5000XVN - Workstation Board Motherboard Manual de usuario

Intel

Intel Desktop Board D2700DC Manual de usuario

Intel

Intel DH67VR Manual de usuario

Intel

Intel D946GZIS - Desktop Board Motherboard Manual de usuario

Intel

Intel D865GSA Manual de usuario

Intel

Intel Desktop Board D845GLVA Manual de usuario

Intel

Intel i845E Manual de usuario

Intel

Intel D945GCLF2 Guía de configuración

Intel

Intel DH61CR Manual de usuario

Intel

Intel D915GMH Manual de usuario

Intel

Intel P45 Series Manual de usuario

Intel

Intel BLKDQ965GFEKR Guía de configuración

Intel

Intel D915GUX Manual de usuario

Intel

Intel BOXD945PVSLKR Guía de configuración

Intel

Intel D945GCZ - Desktop Board Motherboard Manual técnico

Intel

Intel D848PMB Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario