Insys icom EBW-E Manual de usuario

ENGLISH

Quick Installation Guide

EBW-E

www.insys-icom.com

These short operating instructions apply for the following devices of INSYS icom:

▪EBW-E100

www.insys-icom.com/manual 

It is intended for a quick commissioning by the operator. Refer to the associated manual for further information.

This and other associated manuals can be found on our website in the menu Support > Documentation and

Downloads. Scan the QR code above or enter the URL into your web browser.

Defects Liability Terms

A use other than the intended use, an ignorance of the safety instructions and the documentation, the use of insufficiently qualifi ed

personnel as well as unauthorised modifications exclude the liability of the manufacturer for damages resulting from this. Th e liabilityof the

manufacturer ceases to exist.

In tended Use

The product may only be used for the purposes specified in the function overview of the manual. In addition, it may be used f or the

following purposes:

▪Usage and mounting in an industrial cabinet.

▪Switching and data transmission functions in machines according to the machinedirective 2006/42/EC.

▪Usage as data transmission device, e.g. for a PLC.

The product may n ot be used for the following purposes and used or operated under thefollowing conditions:

▪Use, control, switching and data transmission in machines or systems in explosive atmospheres.

▪Controlling, switching and data transmission of machines, which may involve risks to life and limb due to their functions or when a

breakdown occurs.

Technical Boundaries

Max. line length for power supplies, inputs and outputs as well as other signals: 30 m

Cable cross-section: 0.25 … 2.5 mm², flexible lines require end sleeves

Support

If you need further support, please contact your sales partner or INSYS icom support. You can contact our support department via e-mail

under support@insys-icom.de.

Technical Data

The product is only intended for the use within the permissible technical limits specified in the data sheets. These limits must be observed.

Operating voltage

10 V … 48 V DC (±20%)

Temperature range

-30 °C … 70 °C

(85 °C restricted)

Power consumption

typ. 2.0 W, max. 3.0 W

Maximum permissible humidity

95% non-condensing

Real-time clock (RTC) buffer time

typ. 2 days

IP rating

Housing IP40

Connectors IP20

ENGLISH

Quick Installation Guide

EBW-E

www.insys-icom.com

Router connection

1. Connect supply voltage (10 V … 48 V DC (±20%))

to the terminals 10…48 V and GND

2. Connect router (LAN 2 / ext) to the DSL modem or Internet router

3. Connect router (LAN 1) to the configuration PC via Ethernet cable

LAN settings of configurations PC (Windows 7)

If a DHCP client is active on the PC, proceed with step C. Otherwise, either enable the

DHCP client or configure a static IP address.

4. Open Network and Sharing Center (e.g. key and search for "sharing")

5. Select LAN connection and Properties

6. Select Internet Protocol Version 4 (TCP/IP) and Properties

Enable DHCP client

7. Obtain an IP address automatically

It is recommended to unplug the

network cable briefly and plug it

again upon activation of the DHCP

client.

Configure a static IP address

Use the following IP address (example):

IP address: 192 . 168 . 1 . 2

Subnet mask: 255 . 255 . 255 . 0

Standard gateway 192 . 168 . 1 . 1

Preferred DNS server: 192 . 168 . 1 . 1

Please note the previous values before

changing the TCP/IP settings to be able

to restore them later.

Web interface access

8. Enter IP address of the router in address bar of the browser

(default: 192.168.1.1)

If a proxy server is enabled in your browser, this must be disabled or the IP address of

the router must be added as exception.

9. Login with User name (default: insys) and Password (icom)

All modified data will only be transmitted to the router after

clicking the OK button.

Refer to the header and display the help text to get helpful

information about the individual parameters in the web

interface.

ENGLISH

Quick Installation Guide

EBW-E

www.insys-icom.com

Integration into a network (LAN (ext))

If the router is in delivery state or has been reset to factory defaults, the configuration

option Fast start after reset to default settings appears upon login.

10. Activate PPPoE connection, if a DSL

connection is to be configured and enter

respective user name and password

Activate DHCP client, if a DHCP server

is active

Set static IP address

and enter IP address and netmask of the

existing network as well as default

gateway address and first DNS server

address

Customer name and device code must only be entered, if the router is to be configured

for the icom Connectivity Suite - VPN (https://connectivity.insys-icom.de).

11. Confirm settings with OK

The COM LED is illuminated green during PPPoE connection establishment and

orange as soon as a connection is established.

If a connection to the icom Connectivity Suite - VPN is configured, the Status LED

will light up green as soon as it is established.

Configuration of access data

User name and password for web interface access must be changed to prevent a

manipulation of the configuration by unauthorised persons.

12. Menu Basic Settings > Web interface: Enter user name and password for

authentication with password

13. Confirm settings with OK

A typo during entering or forgetting the configured access data makes the router

inaccessible until resetting it to default settings.

All essential configuration steps are completed with this. Further configuration depends on

your specific application. Other frequently required settings are available on the following

page.

ENGLISH

Quick Installation Guide

EBW-E

Mat. no. 10014936 –version 13 December 2019 09:53:22 –Subject to technical changes and correction

www.insys-icom.com

IP Address in Local Network

The IP address of the router in the local network does only have to be changed, if the IP

address is already used or a different address range is required.

1. Menu Basic Settings > IP address (LAN): Adjust IP address of the router in local

network

2. Confirm settings with OK

3. Adjust IP settings of the PC for further configuration accordingly, if these are not

obtained automatically (see step B)

4. Menu Server services > DHCP: Adjust address range to the local IP network, if it was

not possible to adjust this automatically

Resetting the router

If it is necessary to reset the router during configuration, this is possible without losing

the settings.

1. Menu System > Reset: Select Reset

2. Confirm settings with OK

Alternatively, press reset key on the device front once for a short time (soft reset)

Resetting the router to default settings

If the router is to be reset to default settings (if the router has already been used for

example), it can be reset to delivery state.

1. Menu System > Reset: Select Load default configuration and reset

2. Confirm settings with OK

Alternatively, press reset key on the device front three times for a short time within

2 seconds

Resetting and initialising the router

If the router is not available any more for any reason, it can be reset and initialised

(settings do not get lost).

1. Press reset key on the device front for at least 3 seconds (hard reset)

The Inline Help opens upon selecting the button ? (Display help text) and provides helpful

information regarding each individual parameter directly in the web interface.

The related Manuals contain detailed information regarding your device and are available on

our website in the menu Support > Documentation and Downloads.

The Configuration Guides are available under https://docs.insys-icom.de and provide helpful

information regarding the integration of your product into your application.

Hereby, INSYS Microelectronics GmbH declares that herein described device types are in compliance with Directives 2014/30/EU

and 2011/65/EU. The full text of the EC Declaration of Conformity is available under www.insys-icom.com/manual.

Tabla de contenidos

Otros manuales de Enrutador de red de insys icom

insys icom

insys icom MRX3 LAN Manual de usuario

insys icom

insys icom ECR-EW300 Manual de usuario

insys icom

insys icom SCR Series Manual de usuario

insys icom

insys icom ECR-LW300 Manual de usuario

insys icom

insys icom MRX LTE Manual de usuario

insys icom

insys icom MoRoS LAN Manual de usuario

insys icom

insys icom SCR-E200 Manual de usuario

insys icom

insys icom MRO-L200 Manual de usuario

insys icom

insys icom EBW-W Manual de usuario

insys icom

insys icom MRX DSL Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad

insys icom EBW-E Manual de usuario

Manuales populares de Enrutador de red de otras marcas