Instruo vinca Manual de usuario
vincâ
Dual VCA
User Manual
3
Description
We’ve all heard the phrase, “You can never have enough VCAs.”
We know it and we totally get it.
With the Instruō vincâ, this truly is the case.
vincâ is a two channel voltage controlled amplifier with both parallel
and series routing capabilities. Each VCA has a different architecture
allowing them to offer unique functionality that both contrasts and
compliments one another.
The top VCA has Input Bias and Input Attenuverter controls over its
four-quadrant multiplication capabilities.
The bottom VCA has an amplitude control that also acts as a CV
attenuator when control voltage is applied. The bottom VCA includes a
Shape control that morphs between linear and exponential
response curves.
Each channel can be used independently (in parallel) or can be
cascaded (in series), by flipping the Mode Switch.
Chain one vincâ to another (and another, and another!) to add mixing
and routing schemes dispersed throughout your entire system.
Features
• Two channel VCA with separate functionality per channel
• Input bias and attenuverter
• Linear and exponential response curves
• Parallel and series configuration
• Infinitely chainable to additional vincâ modules
4
Installation
1. Confirm that the Eurorack synthesizer system is powered off.
2. Locate 4 HP of space in your Eurorack synthesizer case.
3. Connect the 10 pin side of the IDC power cable to the 2x5 pin
header on the back of the module, confirming that the red stripe on
the power cable is connected to -12V.
4. Connect the 16 pin side of the IDC power cable to the 2x8 pin
header on your Eurorack power supply, confirming that the red
stripe on the power cable is connected to -12V.
5. Mount the Instruō vincâ in your Eurorack synthesizer case.
6. Power your Eurorack synthesizer system on.
Note:
This module has reverse polarity protection.
Inverted installation of the power cable will not damage the module.
Specifications
• Width: 4HP
• Depth: 35mm
• +12V: 30mA
• -12V: 25mA
5
in
IO
I O
VCA 1
VCA 2
LINEAR TO EXPONENTIAL SHAPING
UNITY GAIN
DUAL VCA
PARALLEL
SIGNAL ROUTING
SERIES
vincâ | 'vIŋkə | noun (horticulture) genus of small flowering plants
commonly known as the periwinkle
Key
1. Input 1A
2. Input Bias
3. Input Attenuverter
4. Input 1B
5. Output 1
6. Input 2
7. CV Input
8. Amplitude/CV Attenuverter
9. Shape
10. Output 2
11 . Mode Switch
12. Input Back Jack
13. Output Back Jack
51
4
6
7
8
9
10
11
12
13
Front
Channel 1
Channel 2
Back
2
3
6
Channel One
Input 1a: DC coupled input for channel 1.
• This input will accept both audio and control voltage signals.
• Channel 1 functions as a four quadrant multiplier. Signals at
Input 1a will multiply with signals at Input 1b.
Input Bias: The Input Bias will offset signals present at Input 1a.
• Turning the knob anticlockwise will sum a negative DC offset with the
signal present at Input 1a.
• Turning the knob clockwise will sum a positive DC offset with the
signal present at Input 1a.
Input Attenuverter: The Input Attenuverter scales and inverts the signal
present at Input 1a.
• If there is no control voltage patched at Input 1b, it receives a
normalled +5V reference signal. The scaled and/or inverted signal
from Input 1a sums with the Bias and multiplies with this unity gain
reference signal.
7
• Setting the knob to the center position will attenuate the signal at
Input 1a.
• Turning the knob anticlockwise will scale the inversion of the signal
at Input 1a.
• Turning the knob clockwise will scale, but not invert, the signal at
Input 1a.
Input 1b: DC coupled input for channel 1.
• This input will accept both audio and control voltage signals.
• Channel 1 functions as a four quadrant multiplier. Signals at Input
1a will multiply with signals at Input 1b.
Output 1: Channel 1 output.
• This output is normalled to the module’s series/parallel routing.
• When patched, the output signal will not proceed farther within the
internal routing.
8
Channel Two
Input 2: DC coupled input for channel 2.
• This input will accept both audio and CV signals.
CV Input: DC coupled control voltage input for channel 2.
• This input will accept both audio and control voltage signals.
• Incoming signals are half wave rectified at the CV Input. Any
negative portions of external signals will be cropped to 0V.
Amplitude/CV Attenuator: The Amplitude/CV Attenuator is a
dual-purpose fader for Channel 2.
• The fader controls the amplitude of the signal present at Input 2.
When no control voltage signal is connected, the CV Input receives
a normalled +5V reference voltage.
• Unity gain is set when the fader is set to approximately two thirds of
its maximum range. Any fader position above that will add gain to
the signal.
• When control voltage is applied, the fader becomes an attenuator
for the signal present at the CV Input of channel 2.
• Unity gain of the incoming control voltage signal is set when the
fader is at approximately two thirds of its maximum range.
9
Shape: This control sets the response curve of channel 2.
Turning the knob anticlockwise will
set the response curve to linear.
Turnining the knob clockwise will
set the response curve towards
exponential.
Turning the knob towards
exponential will increase the
available gain range beyond the
fader’s unity gain position.
Output 2: Channel 2 output.
Mode Switch: The Mode Switch designates the internal routing of the
normalisation from the Output of Channel 1.
If the switch is set to the top position, the internal routing is set to
Parallel. Both channels can sum at the Output of Channel 2.
Channel 1 will only sum at the Output of Channel 2 if the Output of
Channel 1 is unused and unpatched.
If the Output of Channel 1 is used, the summing normal will be broken
and both channels will function completely independent.
10
If the switch is set to the bottom position, the internal routing is
set to Series, where the output of Channel 1 will cascade and
normal to the input of Channel 2.
• Channel 1 will only cascade to Channel 2 if the Output of Channel
1 and the Input of Channel 2 are unused and unpatched.
• This configuration allows for scaling, inverting and biasing of a
signal through Channel 1 with master amplitude control via
Channel 2.
• This unity gain position remains constant regardless of the Shape
response curve position.
VCA 1VCA 2
VCA 1VCA 2
Tabla de contenidos
