Inspur NF5468M6 Manual de usuario
Warnings!
15kg
30kg
50kg
For devices ≥ 15 kg, it requires at least 2 people.
For devices ≥ 30 kg, it requires at least 3 people.
For devices ≥ 50 kg, it requires at least 4 people.
请保留本文档，以便于日后查阅。
Watch out for the scratches that may be caused by the cabinet, chassis or rails.
Be aware of electric shock when installing the servers into the cabinet in use.
●DO NOT block the vents on the server during installation, especially the vents on
the front and rear of the server.
●Remove the protective film from the chassis before installing servers into the rack.
●For proper ventilation, leave a minimum space of 15 cm between two servers.
●For easy access of the front and rear ports and cabling, leave a minimum space of
70 mm between the front side of the server and the inner side of the cabinet’s front
door, and 150 mm between the rear side of the server and the inner side of the
cabinet’s rear door.
●Always keep the air baes in place to ensure proper air flow and avoid air
turbulence in the server room.
●Installation must comply with local and regional electrical regulations. To reduce
the risk of personal injury, fire, or damage to the server, DO NOT overload the AC
supply that provides power to the rack.
●Servers can only be deployed in dedicated cabinets with ventilation holes or
specialized cooling cabinets to avoid server failure from overheating as they are
high power appliances.
●In case of multiple-server deployment, always load from bottom to top and place
the heavier server on the lower bay.
●DO NOT install devices beyond the cabinet’s load-bearing capacity, power supply
capacity and heat dissipation capacity.
Rack-Mounted Server
Installation Guide
V1.0
Installing the Rails to the Rack
Installing the Server to the Rack
3
5
1
2
3
4
6
1
5
Inner Rail
Rear Bracket
Outer Rail
Middle Rail
Front Bracket
1
Middle Rail
Inner Rail
2
4
2
Rack-Mounted Server Installation Guide
V1.0
The rails are intended for square hole racks (9.2*9.2 mm, 9.5*9.5 mm) and round hole
racks (Ø7.1 mm).
Insert the pins as indicated by the arrow until the pins are fully engaged. Align and attach the keyholes of the inner rail to the stando s on the side of the
server, and then slide the inner rail toward the rear of the server to the locked
position.
Repeat Step 2 and Step 3 for the other inner rail.
Align and slide the inner rails to the middle rails along with the server. Gently
push the server all the way into the rack.
Tighten the four captive screws.
Repeat Step 1-4 for the other rail.
NOTE: The front end and the rear end of the rail, and the two rails MUST be
installed at the same height.
Fully extend the inner rail until it clicks into a locked position. Repeat the same
step to extend the other inner rail.
Pull up the locking tab to remove the inner rail.
Align the pins on the rear bracket to the desired position of the back of the rack. Press
the locking latch as indicated by the arrow.
Insert the pins as indicated by the arrow until the pins are fully engaged.
Slide the inner rail to its fully closed position. Align the pins on the front bracket to the
desired position of the front of the rack. Press the locking latch as indicated by the
arrow.
1
2
Install the rear end of the rail to the cabinet.
Pull the extended bracket. Keep the front and rear ends on the same
level.①Press the rear of the latch to open it. ②Align the guide pins on the
rear end of the rail with the rack holes, push the rail in the direction of the
arrow, and release the latch to lock it to the rack.
Installing Rails
Install the front end of the rail to the rack.
Position the rail on the rack. ①Press the rear of the latch to open it.
②Align the guide pins on the front end of the rail with the rack
holes,push the rail in the direction of the arrow, and release the latch to
lock it to the rack.
1
Lift the server and place its rear end on the rails first, and then push the
server horizontally into the rack from the front end.
2
Locate and tighten the screws (open the small cover first) in the left and right
ears of the server.
Installing Server
3
Repeat steps 1 and 2 to install the other side.
Front&Rear End of the Rail
Front Rear
2
1
2
1
Rack-Mounted Server Installation Guide
V1.0
Otros manuales de Servidor de Inspur
Inspur
Inspur NF5288M5 Manual de usuario
Inspur
Inspur Yingxin NX5440M4 Manual de usuario
Inspur
Inspur Yingxin Manual de usuario
Inspur
Inspur NF5280M5 Manual de instrucciones
Inspur
Inspur TS860M5 Manual de usuario
Inspur
Inspur I48 Manual de usuario
Inspur
Inspur NF5266M6 Manual de usuario
Inspur
Inspur NF3120M5 Manual de usuario
Inspur
Inspur SA5212M4 Manual de usuario
Inspur
Inspur Yingxin Manual de usuario
Inspur
Inspur SA5112M4 Manual de usuario
Inspur
Inspur Yingxin Manual de usuario
Inspur
Inspur NF5280M6 Manual de usuario
Inspur
Inspur NX8840 Manual de usuario
Inspur
Inspur NF5468A5 Manual de usuario
Inspur
Inspur ON5263M5 Manual de usuario
Inspur
Inspur NF5468M5 Manual de usuario
Inspur
Inspur NF5280M6 Manual de usuario
Inspur
Inspur NF5266M5 Manual de usuario
Inspur
Inspur NF8260M5 Manual de usuario
