1. Connect the output cable to the DRV body. Insert the
DRV into a DC12V or DC24V car charger socket. The
power indicator LED will flash 3 mes.
2. Press the ON/OFF switch. The power indicator light
and the rotaonal wheel indicator will light.
3. Adjust the rotaonal wheel to your desired voltage in
the following increments:
4.2V, 4.4V, 4.6V, 4.8V, 5.0V, 5.2V, 5.4V, 5.6V, 5.8V,
6.0V, 6.2V, 6.4V
4.
Aach the atomizer to the output port. The output
electricity board drive atomizer will be acvated and
the working indicator LED will light.
5. To power OFF: Press the ON/OFF switch again. The
power indicator light will turn off. The DRV will
power off and output will cease.
6. Short Circuit Protecon. If there is a short circuit the
1：Atomizer connecon port
2：Output port
3：Working indicator light
4：Output board
5：Output port
6：Output cable
7：Input port
8：Main body output
9：Rotaonal wheel
10：ON/OFF switch
11：Power LED
12：Rotaonal wheel indicator light
13：Main body
14：Input negave
15：Input posive
16：Manual switch part
The rotaonal wheel adjusts voltage in the following
increments:
4.2V, 4.4V, 4.6V, 4.8V, 5.0V, 5.2V, 5.4V, 5.6V, 5.8V,
6.0V, 6.2V, 6.4V
Scale display voltage improves intuive control and
provides more accurate performance.
FEATURES:
OPERATION GUIDE:
Scale Display Voltage:
Variable Voltage:
Power indicator light will flash 20 mes and a buzzer
will chirp 20 mes. The power indicator light will
switch off and the DRV will stop output.
7. Over rate vaping protecon: The power indicator LED
will flash and the buzzer chirp as a warning if the
vaping interval me is below 3 seconds aer having
be used/vaped 15 mes.
8. The rotaonal wheel LED will blink if the rotaonal
wheel is not correctly in place.
To set your desired voltage turn the rotaonal wheel
to the le or right unl you hear a click.
When adjusng the voltage with the rotaonal wheel
please check to ensure the wheel is set to the desired
voltage.
9. When the iTaste DRV has been powered on hold the
buon down to acvate the unit and commence
vaping.(Manual switch part)
2.
If the rotaonal wheel indicator light flashes
connuously please ensure that the rotaonal wheel
is correctly set in place.
3. If no vapor is produced please check that the output
cable is securely aached to the DRV and the
atomizer and that the indicator LED is lit.
4. If there is a burnt taste: please check if the atomizer
has enough e-juice and adjust the DRV rotaonal
wheel to a lower voltage seng.
Please ensure that you are using lower waage for
low-resistance (ohms) accessories and higher
waage for high-resistance (ohms) accessories.
5. If the buzzer is chirping please check to see if the
atomizer has a short circuit or if over rate vaping
protecon has been acvated.
1. If the power indicator does not light when you press
the ON/OFF buon please do the following:
Check that the DRV is securely fied into the car
charger socket and there is standard power output.
Following this check for fuse damage. Lastly the
ON/OFF buon, power indicator LED, or operaon
board may be malfunconing. In this case please
return the unit to your Authorized Innokin Vendor
for further informaon.
TROUBLESHOOTING:
12
3
4
5
16
6
715
14
13
8
9
10
11
12
