Inmes IM-30 MM Manual de usuario

0504269

SAP:147/153

!!! For your safety In order to obtain

higher performance of your equipment !!!

Read the instructions manual carefully

OPERATIONS MANUAL

Http://www.inmes.com.br

IM-30 MM

RUS

INMES Industrial Ltda – IM-30 MM

CONGRATULATIONS!

Congratulations for choosing the IM-30 MM and thanks for your confidence in INMES products.

This equipment was developed to satisfy safety and meet your needs for high performance. The

IM-30 MM was especially designed to make high-quality cuts in wood, profiles, however each material

requires the proper blade.

We developed this Owner’s Manual to help you install and use your machine correctly in order to obtain

the maximum benefits of economy and output.

Read the manual carefully and call us to answer any question you may have about your equipment and it’s

operation.

Visit our web site:

http://www.inmes-usa.com

Visit us and check out our wide range of products.

INMES Industrial Ltda – IM-30 MM

1 – SAFETY INSTRUCTIONS

For operator safety and durability of your equipment, the instruction must be carried out with great

care when installing and operating your machine, staying alert and learn how to use the IM-30 MM.

1.1 – Safety Signals

DANGER

If the safety instruction is not followed the operator will be seriously injured or killed.

WARNING

Means if the safety instruction is not followed the operator could be seriously injured or killed.

CAUTION

Safety instruction if not carried out with care, might injury the operator.

1.2 – Before using the machine

1.3 – Blade Requirement

The saw blade must proceed the following specifications:

•Extern diameter => 300 mm;

•Arbor diameter => 30 mm;

•Blades marked for 4 000 rpm or higher;

•Blades must be appropriated for each specific material (wood or plastic);

WARNING

!Read the owner’s manual before operating the equipment;

!Wear safety goggles,

!Keep the acrylic blade guard down;

!Keep hands out of the saw blade path;

!Turn off and wait for blade to stop, before adjusting;

!Before plugging in the machine to the electrical INMES Industrial recommends to use a thermo

magnetic circuit breaker on the electrical source as instructed in item 5.3 described in this

instructions manual;

!The manufacturer advice: you should make sure the circuit is properly grounded, using the

green and yellow wire for this purpose;

!The machine must be mounted on a flat surface in an appropriate work area, well lighted and

enough air;

!This machine only accept blade of 300mm

!In order to obtain high performance at work, make sure that you read the owner’s manual.

DANGER

!Do not use high speed steel sawblade because our sawblades work at a 1200rpm.

INMES Industrial Ltda – IM-30 MM

1.4 - When Installing the equipment

•The machine must be mounted on a flat surface in an appropriate work area, well lighted and enough air;

•Before switching on the machine, verify the frequency and voltage;

•The electrical installation should be made by an electrician, as well as questions or problems you may

have with your electric installation should be resolved by an electrician;

•Make sure you are using the correct voltage.

1.5 - Before Each Use

•Make sure switch is in OFF position before plugging in

•Make sure before operating that all parts and connections are tight;

•Keep the machine free from cutting residuals;

•Remove any existent foreign objects or tool between the fence and clamping;

•Verify blade spreader before start again;

•Always use the acrylic blade guard assembled;

1.6 – To reduce the risk of injury

•Never place your hand near the blade;

•Hold the profile firmly to the fence;

•Be careful when cutting small pieces,

the profile or small scrap may move

and break the blade or even damage

other parts;

•When cutting long profiles, its

necessary to use extension table (

have our authorized distributor called

), this accessory will let the profile

lay flat on the extension during

cutting operation;

•Let the blade get full speed before

cutting;

•Do not use blades which are not in a good shape, for instance, broken teeth, because they are out of

balance and will not make good cuts, as well as creating a hazard for the operator;

•Before starting the machine make sure that no objects have been left on the base;

•Soldered and unbalance blade must not be used;

•If any part is missing, bent or broken in any way, or electrical part does not work properly, turn the saw

off, unplug the saw and provide the proper maintenance;

•Never use your machine if you observe something which can cause an accident or damage the machine;

•Use only sharp blade;

CAUTION

•When cutting the profiles, the rabbet must be

facing the operator, as shown in figure 01 (F). Must

be avoid cuts as figure 01 (C) or else the saw blade

can pull the scrap piece into the machine, and that

way offering risk to the operator or damage to the

machine.

•In order to obtain a good finishing and safety when

cutting observe on top of the profile that you must

allow at least 3/8” (10mm) of wood between the

cut and the end of the stick as figure 01 (B).

INMES Industrial Ltda – IM-30 MM

•Keep the saw blade clean;

•Keep work area around clean, sawdust can

make the floor slippery;

•Make sure there is no debris between the

work piece and the fence;

•Never cut more than one work piece at a

time;

•Anytime the saw blade is removed for

replacement or maintenance; make sure

that the machine is unplugged from the

wall socket;

•After replacing make sure the blade is

properly tight;

•Keep visitors and children away when using;

Note: Always remember that careless fraction

of a second is enough to cause a severe injury

1.7 – Plan your cut

•Make sure the machine has enough cutting capacity to cut the profile you wish to;

•Use appropriate blade for cutting, depending on the type of material to be cut ( wood or plastic);

•When cutting the profiles with rabbet, the rabbet must be facing the operator as figure 01 (F).

1.8 – Protection:

•Do not wear loose clothing, gloves or jewelry, neckties. They can caught you and draw you against the

moving parts;

•Tie back long hair;

•Wear ear plugs or muffs;

•Always wear safety goggles;

•For dusty operations, wear a dust mask along with safety goggles;

•Always remember that a fraction of a second can cause a serious injury.

Tip:

!When you have a large quantity of profiles to be cut, and you want to do this in a quick way, we advice the

operator to cut first one side, and then the other side. It means rapidity and will save your time, for it’s

not necessary to move the blade position several times.

3/8”

Right

Wrong

Rabbetfacing the operator

profile

scrap piece

Figure 01

Wrong Right

scrap piece

profile

INMES Industrial Ltda – IM-30 MM

WARNING

Before leaving the machine

•Turn the saw off and wait for all moving parts stop;

•Unplug the saw;

•Disconnect the circuit breaker from the power.

2– UNPACKING AND CHECKING CONTENTS

As soon as you receive the IM-30 MM Rotating Miter Saw, make sure that all parts are included.

The following parts are included:

Part or Assembly Quantity

Basic IM-30 MM Rotating Miter Saw 01

Mechanical Clamping System 01

RightTableExtension 01

LeftTableExtension 01

MouldingStop 01

Combination Wrench 24 x 27 mm 01

Phillips3/16”x4” 01

Wrench (for motor flange ) 01

Allen6mm 01

Warranty 01

INMES

RepairCenter 01

Owner’sManual 01

INMES Industrial Ltda – IM-30 MM

Optional Accessories:

♦Additional Right Table Extension ♦Work Stand

♦Additional Left Table Extension ♦Additional accessory for Fence

♦90º moulding stop or 45º moulding stop

3 –

GETTING TO KNOW YOUR MITER SAW

WARNING

!If you are missing any part, do not assembly

the saw, contact our authorized distributor.

DANGER

!Do not plug the power cord into a power source

outlet when unpacking and assembling.

CAUTION

!To avoid back injury get help

whenever you have to lift the saw.

!Inmes developed a movable base for

IM-30; contact our distributor for

further information.

!Place the saw on a secure work

surface.

Important:

!Before installing the machine, make sure that you

have all the parts included.

!If you are missing any part, please do not hesitate to

contact our distributor.

!Always order by part number, use “Vista explodida”

you may find it at the list of parts located in the end

of the manual.

!This manual is extremely useful when ordering spare

parts, therefore keep it in a appropriate place,

should you have more than one equipment the same

model, identify the equipment writing the serial

number on its manual.

INMES Industrial Ltda – IM-30 MM

4 –

INSTALLING THE EXHAUST CABINET

To install the exhaust cabinet you must

fit the part (01) into the hose and then

attach this end of the hose over the

aluminum saw casting outlet using a

clamp 02 to tighten it. Once this

procedure is done attach the other side

of the hose over the dust collector

located inside the cabinet using a clamp

to tighten the hose.

As the saw dust is collected in a cloth

bag located inside the cabinet, we do

recommend to empty the bag at least

twice a week in order maintain the high

performance of your equipment.

In order to turn the dust collector on

and off you must press the switch 03

and then turn on the saw by pushing the

switch 04 fig. 02.

(Russia model)

1° - Attach the main switch 05 to the cabinet base 06 using the washers 07 and bolt 08 as shown in fig.

02.

2ª – Turn the main switch 05 fig.02.

3ª – Turn on the dust collector 03 fig. 02.

4ª – Turn on the saw 04 fig. 02.

1ª – Turn off the saw 04 fig. 02.

2ª – Turn off the dust collector 03 fig. 02.

3ª – Turn off the main switch 05 fig. 02.

INMES Industrial Ltda – IM-30 MM

5 –

IM-30 MM ELECTRICAL INSTALLATION

!To reduce electrical shocks or damage to the machine, unplug it from the power source before any

maintenance;

!If power cord is worn, cut or damage in any way, you must replace it right way;

!The electrical service must be performed by an specialist;

!Always install the machine in a dry floor, never expose the equipment in rain;

!Never place your hand or finger on the terminals of plug when installing or removing the plug to or from

the outlet;

!Overloading can occur if the operator start and stop many times in a short time, also the use of

improper or dull saw blades are used;

!Before plugging in the machine to the electrical INMES Industrial recommends to use a thermo

magnetic circuit breaker on the electrical source as instructed in item 5.3 described in this instructions

manual.

When using the machine for the first time, the operator must check out if the direction rotation of the

motor is right, otherwise he (she) must invert it.

•To invert the direction rotation in three phased machines, its necessary the inversion the two of the

three wire from power source, changing one for another. This proceed must be done by a specialist.

•To invert the direction rotation in single phased machines, you must change the wires position 5 and 8

(change one for another), inside the connection box. This proceed must be done by a specialist.

5.1 - Motor specifications for IM-30 MM

Induction motor three phase or single phase.

Available in: Consumed Power kw/h: Amps:

115 V Single Phase 1,27 kw/h 11,00 A

208-230 Single Phase 1,22 kw/h 5,55 A

Rotation 3400rpm

Power 1 hp

Frequency 60Hz

50Hz

Bearing

Front 6204 DDU ARZ S1

Back 6201 ZZ ARZ S1

WARNING

!Read the manual and the safety instruction carefully before connecting the plug to the power source.

!Make sure that all the screws are tight before installing the machine.

Tabla de contenidos

Otros manuales de Sierra de Inmes

Inmes

Inmes IM-300PL AL Manual de usuario

Inmes

Inmes IM-300PL AL Manual de usuario

Inmes

Inmes FF-325 PLUS Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario