INKPOT INKPOT-I06 Manual de usuario
2.4G REMOTE CONTROL DRONE
AGE 14+
After-sales email:[email protected]
INKPOT-I06
*Please read this manual carefully before operation and keep it properly
for future reference.
CONTENTS
Package List
Battery Charging
Battery Installation
Know Your Drone
Flight Environment
Know the Remote Controller
Functions in Operation Level 1
Start up
Pairing
One Key Start
Basic Control
Altitude Hold
Fine-tuning Mode
Re-calibration
Low Power Warning
One Key Landing/Emergency Stop
Function Enabled in Level 2
How to Activate Operation Level 2
Self Rotation
Functions Enabled in Level 3
How to Activate Level 3
Speed Switch
360° Flip & Roll
Headless Mode
Battery Instructions
Trouble Shooting
1
1
2
3
4
5
6
6
6
6
7
7
7-8
8
8
9
9
9
9
10
10
10
11
11-12
13
14
Package List
Battery Charging
Screwdriver
①Connect the USB charger with adapter (output: 5V/0.5~2.0A), LED on
the charger glows red;
②When the battery is connected with the charger, LED on the charger
lights off;
③The LED glows red again when charging is completed;
④It takes roughly 80 minutes to fully charge the battery.
Note: Never use fast charger or any adapter with output over 5V, as it may
damage the charger and battery.
-1-
2.4G REMOTE CONTROL DRONE
AGE 14+
After-sales email:[email protected]
INKPOT-I06
*Please read this manual carefully before operation and keep it properly
for future reference.
Spare
Spare 2
Battery Installation
Push up the battery slot cover and install 3*AAA batteries (not included)
Note：
①Slide the battery’s rear (the side without holder) in the battery slot, then
press the head down to install the battery.
1. Install Batteries in Remote Controller
2. How to Install/Uninstall Drone Battery
①Always pay attention to battery polarity when installing battery;
②Do not mix old and new batteries;
③Never use different types of batteries together.
Know Your Drone
②Keep pushing in the holder on the battery and pull the battery up to
take it out.
Propeller B
Upper Shell
Propeller A Power Switch
Lower Shell
Battery
Flight Environment
Please select an optimal flying environment.
Indoor: Spacious spaces away
from barriers, crowds or pets
are preferred.
The drone is supposed to be
used indoors, do not fly it
outdoors unless there’s no wind.
Please keep the drone insight
during the flight and keep it
away from barriers,
high-tension cables, trees
and people.
Do not fly in extreme environment,
such as hotness, coldness,
strong wind or heavy rain.
Place the drone on flat surface before taking off.
Never take off on rugged surface.
Notes:
Notes:
Know the Remote Controller
The drone has 3 levels of operation modes:
Level 1: for newbie to learn basic operations;
(the remote controller beeps one time when
it's paired in this mode)
Level 2: for competent, some stunt functions
are unlocked; (remote controller beeps 2
times). Function unlocked in level 2 will be
marked with yellow color below
Level 3: senior only, functions of this drone are
all available now. (remote controller beeps 3
times). Functions unlocked in level 3 will be
marked with red color below
Short press: Speed Switch
Keep
Pressing
Keep
Pressing
Short press: Self Rotation
Short press: Flip & Roll
Long press: Headless Mode
Short press: One Key Start/Landing
Long press: Emergency Stop
Power Switch
Pull the joysticks down-left to re-calibrate
Short press: Light Switch
Long press: Fine-tuning Mode
Functions in Operation Level 1
Pull the left joystick up and down to attempt pairing, the remote controller
beeps one time in each pulling, and the drone's flashing indicator lights
become constant when it’s paired successfully.
②Press power switch on the remote controller, the remote controller
beeps one time indicates it's turned on in operation level 1 (for newbie).
①Keep pressing the Power Switch until indicator lights start flashing,
then place the drone on horizontal surface with it facing to the front.
(1) Start Up
(2) Pairing
Short press the One Key Start button, propellers on the drone will be
unlocked and start spinning. Pull up left throttle to take off.
(3) One Key Start
This drone has altitude hold function. Player can release the left joystick
in flight to let the drone hovers at current altitude.
③The Fine-tuning Mode ends automatically when player stopped operating
for more than 2 seconds, or manually by long pressing the Light Switch
button again.
②Long press the Light Switch button until the remote controller beeps
and indicator light starts flashing, which indicates the drone is in
Fine-tuning Mode. Tip right joystick to opposite side of the sliding direction
to adjust, until the drone appears hovering still.
(4) Basic Control
(5) Altitude Hold
①If the drone appears sliding to a direction when hovering, please adjust
it in Fine-tuning Mode.
If the drone slides severely on takeoff and could not fly properly, please
place the drone on a horizontal position and pull joysticks down-left to
re-calibrate it. Indicator lights on the drone start flashing quickly and then
become constant again indicates the drone is re-calibrated.
(7) Re-calibration
When the drone is in low-power, indicator lights on it will start flashing
quickly. Player needs to maneuver the drone back, or it would descend
automatically soon when power is extremely low.
(8) Low Power Warning
Fine-tuning Direction
Tabla de contenidos
