Inkel MB8811C1 Manual de usuario
Operating Instructions
Copyright 2017 by INKEL
Bluetooth Module for Audio
Bluetooth Module
Model: MB8811C1
Operating Instructions
OEM/Integrators Installation Manual
Operating Instructions
1 Copyright 2017 by INKEL
General Description
MB8811C1 is a fully integrated Bluetooth module. It is based on CS ’s Bluecore
8811 chip with specific interface design to meet Inkel Corporation’s needs.
MB8811C1 is compatible with Bluetooth specification version 4.0. It integrates F,
Baseband controller, etc., a completed Bluetooth subsystem.
Features
- Dual-mode Bluetooth / Bluetooth low energy radio
- Stereo codec with 2 microphone inputs
- Fast Charging support up to 200mA with no external components
- Multipoint support for A2DP connection to 2 A2DP source for music playback
- aptX, SBC, MP3, AAC and Fast stream decoder
- Built-in eference Clock: 26MHz
- oHS Compliant
Applications
- Stereo headsets
- Wired stereo headset and headphones
- Portable stereo speakers
- Audio Products
Pattern Antenna
- Frequency ange : 2400 ~ 2500 MHz
- Peak Gain(MAX) : 1.396 dBi
Device Overview
Operating Instructions
2 Copyright 2017 by INKEL
Dimensions
Operating Instructions
3 Copyright 2017 by INKEL
Block Diagram
Operating Instructions
4 Copyright 2017 by INKEL
Pin Descriptions
Operating Instructions
5 Copyright 2017 by INKEL
Example Application schematic
Electrical Characteristics
Operating Instructions
6 Copyright 2017 by INKEL
Operating Instructions
7 Copyright 2017 by INKEL
Module’s Label Information
Inkel Corporation
FCC ID: VNH-XXXXXXXXXX
IC: XXXX-XXXXXXXXXX
CMIIT ID: XXXXXXXXX
XXX-XXXXX
Operating Instructions
8 Copyright 2017 by INKEL
Regulatory
USA
The MB8811C1 module has been labeled with its own FCC ID number, and if the
FCC ID is not visible when the module is installed inside host audio device.
Then the outside of the finished product into which the module is installed must also
display a label referring to the enclosed module. This exterior label can use wording
as follows:
This device complies with Part 15 of the FCC ules. Operation is subject the FCC ules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
And (2) this device must accept any
interference received, including interference
that may cause undesired operation
A user’s manual for the product should include the following statement
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED
BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
FCC Information to User
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-nected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operating Instructions
9 Copyright 2017 by INKEL
CANADA
The MB8811C1 module has been labeled with its own IC number, and if the IC is not
visible when the module is installed inside host audio device.
Then the outside of the finished product into which the module is installed must also
display a label referring to the enclosed module. This exterior label can use wording as
follows:
A user’s manual for the product should include the following statement
EUROPE
Hereby declares that this Bluetooth module is in compliance with the essential requirements
and other relevant provisions of &TTE Directive 1999/5/EC. The standards for complying
are as following:
ETSI EN 301 489-1 V1.9.2: 2011-09
ETSI EN 301 489-17 V2.2.1: 2012-09
ETSI EN 300 328 V1.9.1:2012-06
EN 62479: 2010
EN 60065:2002 + A1:2006 + A11:2008 + A2:2010+A12:2011
Tabla de contenidos
Otros manuales de Unidad de control de Inkel
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
