INHECO Heated Lid Manual de usuario

Doc ID: 900678-001

July 2020

INHECO Heated Lid

Heated Lid

Part No.: 8900033

► User´s Manual

INHECO 02

Doc ID: 900678-001

July 2020

INHECO Industrial Heating and Cooling GmbH reserves the right to modify their

products for quality improvement. Please note that such modifications may not be

documented in this manual.

This manual and the information herein have been assembled with due diligence.

INHECO GmbH does not assume liability for any misprints or cases of damage resulting

from misprints in this manual. If there are any uncertainties, please feel free to contact

[email protected]. → How to contact INHECO, page 5.

The brand and product names within this manual are registered trademarks and belong

to the respective titleholders.

INHECO 03

Doc ID: 900678-001

July 2020

TABLE OF CONTENTS

IMPORTANT NOTES ................................................................................ 04

General Information ..................................................................................... 04

Explanation of symbols................................................................................ 04

Explanation of Abbreviations ....................................................................... 05

Warranty ...................................................................................................... 05

How to contact INHECO .............................................................................. 05

PRODUCT DESCRIPTION ....................................................................... 06

Intended Use ............................................................................................... 06

Scope of Delivery......................................................................................... 07

Functional Elements .................................................................................... 07

Labels .......................................................................................................... 08

Technical Data Heated Lid .......................................................................... 09

SAFETY INSTRUCTIONS ........................................................................ 10

Product-specic Risks ................................................................................. 10

Technical Alterations ................................................................................... 11

Malfunctions................................................................................................. 11

HARDWARE INSTALLATION.................................................................. 12

Scope of Supply........................................................................................... 12

Initial Operation............................................................................................ 12

Labware Use................................................................................................ 13

SOFTWARE INSTALLATION .................................................................. 13

DAILY USAGE........................................................................................... 13

MAINTENANCE......................................................................................... 14

Software Updates ........................................................................................ 14

Trouble-Shooting & Support ........................................................................ 14

Cleaning....................................................................................................... 15

Decontamination.......................................................................................... 16

Calibration / Verication............................................................................... 16

Return for Repair only with RMA Number ................................................... 16

Transportation and Storage ......................................................................... 16

Shut Down and Disposal ............................................................................. 16

ACCESSORIES ......................................................................................... 17

Multi TEC Control (MTC) / Single TEC Control (STC)................................. 17

Slot Modules ................................................................................................ 17

Miscellaneous .............................................................................................. 17

APPENDIX ................................................................................................. 18

INHECO 04

Doc ID: 900678-001

July 2020

1 IMPORTANT NOTES

1.1. General Information

Read the user instructions completely. The manual explains how to operate and handle

the Heated Lid (8900033). In case manual instructions are not followed, injury or product

damage cannot be excluded.

Missing or insufficient knowledge of the manual leads to loss of liability against

INHECO GmbH.

This manual is part of the Heated Lid and must be retained until the device is disposed

and must be passed on with the Heated Lid when the device is taken over on to a new

user.

The Heated Lid meets the acknowledged rules of technology and comply with today‘s

standards.

Manual instructions must be followed in order to ensure safe handling of the device.

Security-related warnings in this manual are classified into three hazard levels:

- The signal word WARNING indicates hazards which – without precautionary

measures – can result in serious injury or even death.

- The signal word CAUTION indicates hazards which – without precautionary

measures – can result in minor to moderate injuries

- The signal word NOTE stands for general precautionary measures that are to be

observed to avoid damaging the device when using it.

- The signal word NOTICE stands for the general measures that help using the device.

Contact INHECO in case there are any uncertainties of how to operate or how to handle

the Heated Lid.

Your opinion about this manual provides us with valuable insights on how we can

improve this document. Please do not hesitate to direct your comments to

[email protected], → How to contact INHECO, page 5.

1.2. Explanation of symbols

Symbol Explanation

Potential danger of serious injury or death →

signal word WARNING or CAUTION indicate the severity.

Caution: Potential danger of hot surface.

· Bullet points indicate steps of instructions.

- Hyphens refer to enumerations.

→ Arrows indicate: “refer to” and are mostly an active link

INHECO 05

Doc ID: 900678-001

July 2020

1.3. Explanation of Abbreviations

The document uses the following terms

°C Degree Celsius

Hz Hertz [1/s]

lac Alternating Current

ldc Direct Current

KKelvin

kg Kilogram

rhu relative humidity

TEC Thermo- Electric- Cooler (Thermoelectric Module)

Uac Alternating Voltage

Udc Direct Voltage

WWatt

ALP Automated Labware Positioners from Beckman Coulter

IVD In Vitro Diagnostic

FDA Food and Drug Administration

MTC Multi TEC Control controls up to 6 INHECO devices individually

STC Single TEC Control controls 1 INHECO device

O󰀨set The di󰀨erence between the set temperature and actual value once the tempe-

rature is stable

PT100 PT100 is a Resistive-Temperature-Detector (RTD). This sensor increases its

resistance with increasing temperature.

Set Point The desired process value programmed into a controller

1.4. Warranty

The warranty period starts on the date of shipment. Any damage caused by operating

the Heated Lid outside the specifications and guidelines leads to the loss of warranty.

Broken seals on INHECO lead to the loss of warranty as well.

INHECO will only accept parts / devices for return that do not pose a threat to the health

of our staff. In particular, the devices may not have been used in Biosafety Level 3 and 4

environments, or have been exposed to radioactive or radiation materials. →

Decontamination and Cleaning, page 16ff.

Devices exposed to Biosafety level 3 and 4 Environments or radioactive materials are

not accepted by INHECO for return.

1.5. How to contact INHECO

INHECO GmbH

Address Fraunhoferstr. 11

82152 Martinsried

Germany

Telephone - Sales +49 89 899593 120

Telephone - Techhotline +49 89 899593 120

Fax +49 89 899593 499

E-Mail - Sales [email protected]

E-Mail - Technical -Hotline [email protected]

Website www.inheco.com

Technical Support & Trouble Shooting Instructions:

http://www.inheco.com/service/technical-support.html

INHECO 06

Doc ID: 900678-001

July 2020

2 PRODUCT DESCRIPTION

2.1. Intended Use

The INHECO Heated Lid is an ideal add-on to avoid condensation on lids / sealed

plates, to increase heating rates and to improve temperature uniformity. The Heated Lid

can be used in combination with all INHECO heating /cooling and shaking devices (with

shaking only limited use).

Power supply, temperature setting and control of the Heated Lid device is performed

through an INHECO TEC Control Unit, please refer to the separate TEC Control

Manual.

The Heated Lid can be ordered with two types of precise temperature/rpm controllers

with integrated power supply (MTC or STC). The unit is a plug-and-play high

performance heating device with CE and UL certification. It is mainly used on robotic

platforms and systems in LabAutomation.

The Heated Lid is designed specifically for use in Life Science and In Vitro Diagnostics. It

is prepared for easy integration into IVD applications, but the final IVD validation has to

be performed by the first marketer (IVD application).

When using the Heated Lid in a Biosafety Laboratory Environment, the user is

responsible for labeling the devices according to the WHO Laboratory Biosafety Manual

(ISBN 92 4154650 6) and for operating the devices according to this Biosafety Manual.

The Heated Lid must be used exclusively by laboratory professionals trained in

laboratory techniques with labautomation systems and having studied the instructions

for use of this instrument as well as the instructions of the workstation the device is used

in.

INHECO 07

Doc ID: 900678-001

July 2020

2.2. Scope of Delivery

Before initial operation, make sure that the shipment of your unit and its scope of supply

is complete and no parts are damaged.

In case of parcel or product damages, make photos of the damaged boxes and products

and email them to [email protected] immediately. Transportation damages

must be reported to INHECO within 7 days of delivery. The following components should

be included in each shipment:

Fig.1: Components

( 1 ) Heated Lid incl. Sub-D-Connector Cable (2)

The Sub-D-Connector Cable is already connected with the Thermoshake and it also

needs to be conntected to the Black Slot Module installed inside the TEC Control Unit

(MTC or STC). → Initial Operation, page 12.

2.3. Functional Elements

The functional element of the Heated Lid is the temperature controlled contact surface.

The device has to be controlled via a TEC Control Unit ( MTC or a STC).

INHECO 08

Doc ID: 900678-001

July 2020

2.4. Labels

The identification label with part number and serial number also contains important

technical indications. The electrical specification on the label must meet your local

situation. The label is placed on the top of the Heated Lid. The identification label must

not be removed. If it has become illegible or falls off, it has to be replaced by a new

identification label. New labels can be ordered at INHECO. In case the label is missing

and you do not know the part number and serial number, they can also be read out with

the software (MTC/STC Demo Tool) which can be downloaded from INHECO´ login

section on www.inheco.com. → Trouble Shooting and Support, page 15f.

Fig.2:

1000

INHECO GmbH

82152 Martinsried / Germany

03PN:

SN:

Input: 24V Imax: 4,8A

8900033-A

Heated Lid

2016-09

Rev.:

Product labels on the device

Fig.3:

INHECO GmbH

82152 Martinsried / Germany

1000

03PN:

SN:

8900033-A

Heated Lid

2016-09

Rev.:

Storage and transportation conditions:

-10°C to +60°C [+14.0°F to +140°F],

10% to 80% RH, non condensing

Shipment labels on the package

Fig.4: Label on instrument

Caution Hot

INHECO 09

Doc ID: 900678-001

July 2020

2.5. Technical Data Heated Lid

Technical Data incl. Dimensions

Input voltage / max. current 24Vdc / 4.8 A

Temperature range ambient to + 115°C

[ambient to +239°F]

Temperature range ambient 15°C to +32°C

[+59°F to 89.6°F]

Sensor type two PT100

Outer dimensions for

Length x width x height in mm

134 x 91 x 19

Weight incl. cord approx. 0.55 kg [1.2 lbs]

Heating capacity 100 Watt

Environmental Conditions

Tolerable relative humidity Operation 30-80% relative (non condensing)

Transportation and

storage

10-80% relative (non condensing)

Temperature Operation +15°C to +32°C [+59°F to 90°F]

Transportation and

storage

-10°C to + 60°C (+14°F to 140°F),

non condensing

INHECO 10

Doc ID: 900678-001

July 2020

3 SAFETY INSTRUCTIONS

3.1. Product-specic Risks

WARNING

Follow the safety instructions given below in order to avoid danger for user and device.

General

- The main power switch of the TEC Control Unit (STC / MTC) must always be

accessible.

- The Heated Lid ("the device") hardly requires any maintenance, except Cleaning →

page 16f.

- The device has to be placed on the labware in an upright position.

- Do not exceed minimum or maximum ambient temperature and humidity conditions

during operation or storage of the Heated Lid → Technical Data, page 9.

- The device must not be used in environments with risk of explosion.

- The device is for indoor use only.

Burning Hazard:

- Device can burn your skin. Even after switching off the TEC Control unit, the

connected device can still be hot and could seriously burn your skin as the material‘s

temperature can reach up to +115°C [+239°F]. It takes a while to cool down after the

device has been used.

Electrical Shock:

- The device must not be used if the device itself or the power cable shows visible

signs of damage.

- You can suffer an electric shock and injuries, if Heated Lid is not connected properly

or if you do not disconnect the device from the TEC Control Unit (STC / MTC) outlet

before opening the housing.

- Never connect or remove the power plug with wet hands.

- Original power cable provided by INHECO has to be used to guarantee safe and

proper operation.

- The wall power outlet for the TEC Control Unit (STC / MTC) must have a ground

earth connection (Safety Class 1).

- Where an ungrounded receptacle is encountered, a qualified electrician must replace

it with a properly (PE) grounded receptacle in accordance with the local electrical

code. Make sure that the electrical specification on the identification label at the side

panel of the device meets your local situation. → Labels, page 8.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario