Infineon ASCLIN Shell UART 1 Manual de usuario
Scope of work
A Shell is used to parse a command line and call the corresponding
command execution. The ASCLIN module is used to interface with the
Shell through the USB port via UART.
The ASCLIN module is configured for UART communication.
The Shell from iLLDs exploits the ASCLIN module to interpret and manage
commands from the user like “info”, “toggle [x]” or “help”.
2
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Introduction
›The Asynchronous/Synchronous Interface (ASCLIN) module provides
serial communication with external devices. In this example, it is used to
interface with the PC through the USB port via UART communication.
›A Shell is a user interface for parsing commands and accessing services.
3
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Hardware setup
This code example has been
developed for the board
KIT_AURIX_TC297_TFT_BC-Step.
The board should be connected to
the PC through the USB port (1).
1
4
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Implementation
Configure the ASCLIN module
The configuration of the ASCLIN module is done by initializing an instance of the IfxAsclin_Asc_Config
structure, which contains the following fields:
›baudrate –a structure that allows to set
–baudrate –the communication speed in bit/s
–oversampling –the division ratio of the baud rate for reaching higher frequencies to ensure
oversampling
›bitTiming –a structure that allows to set the sampling mode with
–medianFilter –the number of samples per bit
–samplePointPosition –the first sample point position
›interrupt –a structure that allows to set
–txPriority, rxPriority and erPriority –the interrupt priorities for transmission, reception and error
events
–typeOfService –the service provider responsible for handling the interrupt, which can be any of the
available CPUs, or the DMA
›pins –a structure that allows to set which port pins are used for the communication
›rxBuffer, rxBufferSize,txBuffer, txBufferSize –parameters that allow to configure the buffers that will
hold the incoming/outgoing data
The function IfxAsclin_Asc_initModuleConfig() fills the configuration structure with default values and
IfxAsclin_Asc_initModule() function initializes the module with the user configuration.
Both the functions can be found in the iLLD header IfxAsclin_Asc.h.
5
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Implementation
Configure the Shell
To configure the Shell, it is needed to firstly initialize a Standard Interface and a Standard IO from the iLLDs.
This is done by the functions IfxAsclin_Asc_stdIfDPipeInit(), Ifx_Console_init() and
Ifx_Assert_setStandardIo(), that can be found respectively in the iLLDs headers IfxAsclin_Asc.h,
Ifx_Console.h and Assert.h.
Furthermore, it is needed to define the macros IFX_CFG_ASSERT_STDIO,
IFX_CFG_ASSERT_VERBOSE_LEVEL_DEFAULT and IFX_CFG_ASSERT_INCLUDE to configure the
Ifx_Assert.h header.
This is done in the configuration header Ifx_Cfg.h.
The Shell is configured inside the function initShellInterface() by initializing an instance of the
Ifx_Shell_Config structure with default values through the function Ifx_Shell_initConfig(). Then, the
following parameters are modified:
›standardIo –that allows to set the module used for serial communication
›commandList –that allows to set the list of commands supported by the shell
The command list is an array of structures of the type Ifx_Shell_Command, that contains:
–commandLine –the actual command which will be sent to the shell by the user
–help –a small description of the command that is shown when help command is given
–data –a link to the shell
–call –the function called when the command is given
The Ifx_Shell_init() function initializes the shell with the user configuration.
The functions Ifx_Shell_initConfig() and Ifx_Shell_init() can be found in the iLLD header Ifx_Shell.h, while
the function initShellInterface() is defined in the header UART_ASCLIN_Shell.h.
6
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Implementation
Run the Shell
The Shell is continuously run through the function runShellInterface() called inside the infinite while loop in
the Cpu0_Main.c file.
It continuously reads the incoming data and evaluates them when the carriage return character is entered.
Configure and control the LEDs
The LEDs are toggled by controlling the port pins to which they are connected using methods from the iLLD
headers IfxPort.h.
The LED port pins have to be configured to output push-pull mode using the function
IfxPort_setPinMode().
During program execution, the LEDs are switched on and off using the function IfxPort_setPinState().
7
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Implementation
Configure the Interrupt Service Routine (ISR)
The function implementing the ISR needs to be assigned a priority and a core responsible for its execution.
This is done with the macro IFX_INTERRUPT(isr, vectabNum, priority).
Since the Shell uses the ASCLIN module to interface with the user, three ISR are needed to be configured for
transmission, reception and error events.
Each of the ISR should call the handler for the respective operation (transmit, receive or error) by passing the
ASC handle.
8
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Run & Test
In order to use the shell interface, a serial monitor (e.g. PuTTY, HTerm) is
required. The serial monitor must be configured with the following
parameters to enable the communication between the board and the PC:
›Port: COMx (e.g. COM5, COM port number depends on the setup)
›Baud rate: 115200
›Data bits: 8
›Parity: None
›Stop bits: 1
›Handshaking: None
9
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Run and Test
Firstly, the serial monitor should be opened.After code compilation and
flashing the device, perform the following steps:
›Type “help” to see the list of available commands
›Type “toggle [0/1/2/3/4]” to respectively: turn on all LEDs, toggle LED
D107, toggle LED D108, toggle LED D109 or toggle LED D110
›Check command execution.
10
2019-10-17 Copyright © Infineon Technologies AG 2019. All rights reserved.
Tabla de contenidos
Otros manuales de Unidad de control de Infineon
Infineon
Infineon TLE9262-3BQX Manual de usuario
Infineon
Infineon PBA 313 07 Manual de usuario
Infineon
Infineon AIROC IFW56810 Manual de usuario
Infineon
Infineon GTM TOM Interrupt 1 Manual de usuario
Infineon
Infineon AIROC CYBLE-343072-02 Manual de usuario
Infineon
Infineon CCU6 PWM Capture 1 Manual de usuario
Infineon
Infineon ASCLIN LIN Master 1 Manual de usuario
Infineon
Infineon I2C Read Ext Device 1 Manual de usuario
Infineon
Infineon GPT12 PWM Capture 1 Manual de usuario
Infineon
Infineon GTM TIM Capture 1 Manual de usuario
Infineon
Infineon Multicore 1 Manual de usuario
Infineon
Infineon Cypress EZ-BLE CYBLE-022001-00 Manual de usuario
Infineon
Infineon HybridPACK 2 Guía del usuario
Infineon
Infineon Cypress EZ-BLE CYBLE-012011-00 Manual de usuario
Infineon
Infineon PG-LQFP Manual de usuario
Infineon
Infineon GTM ATOM PWM 1 Manual de usuario
Infineon
Infineon SMU IR Alarm 1 Manual de usuario
Infineon
Infineon CCU6 PWM Capture 1 Manual de usuario
Infineon
Infineon SPI CPU 1 Manual de usuario
Infineon
Infineon ASCLIN SPI Master 1 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
