Przedsiębiorstwo Informatyczno-Elektroniczne INEL Sp. z o.o., ul. Mostowa 1, 80-778 Gdańsk,
[email protected] www.inel.gda.pl
2.3 Solar panel installation
The solar panel should be glued to the roller shutter box using double-
sided adhesive tape after cutting a hole in the box for the connection
cable and inserting the cable into the box.
The edges of the hole should be smoothed and the cable secured
with a cable gland or tape
Fix the cables to the side of the box so that they do not come into
contact with moving parts.
2.4 Electrical connections
Connect the solar panel plug to the drive socket. Fix the cables to
the side of the box so that they do not come into contact with moving
parts.
After starting, the motor increases its speed until it reaches the
optimum speed
Check the condition of the guard, guides and roller shutter box
before starting / programming the drive.
The roller shutter box and the guides should be free of dirt and ensure
free movement of the roller shutter guide along its entire length.
Guides that are contaminated with construction material or too tight
may cause damage to the drive and the roller shutter, which is not
covered by warranty.
3 Registering the remote control
Use remote controls from Inel's extensive range (except key fobs)
to control the drive. The remote control must be registered.
Registering the remote control involves memorizing the remote
control channel in the drive's memory.
3.1 Registering the first remote control
For drives received from the manufacturer or if the remote control is
lost, the remote control must be registered using the following
procedure:
briefly press (< 2 seconds) the SW button on the drive head
– the drive makes a short up-down movement
select the desired channel on the remote control
press simultaneously the keys ∧ and ∨ on the remote
control – the drive makes a short up-down movement
press the key ∧ for the next 10 seconds – the drive will
confirm the channel registration by making a long up-down
confirmation movement
NOTE: The procedure will erase all previously registered
channels from the drive memory. This allows the registration
of a remote control for the drive when no registered remote
control is available (new drive or case of lost / stolen remote
control).
3.2 Registering another remote control / channel
When you have a previously registered remote control, further
channels of the same or another remote control must be registered
without using the SW button.
To this end:
on the registered remote control simultaneously press the
keys ∧ and ∨ – the motor makes a short up-down
movement
For the next 10 seconds, the drive remains in registering mode. To
register a new channel of the same or a different remote control,
proceed as follows within that time:
select the desired channel on the remote control
press the key ∧ – the drive will make a long confirmatory
up-down movement
With this method, you can register any channel to any drive, but only
if you have a pre-registered remote control.
3.3 Deleting memorised channels
To delete memorised channels, proceed as follows:
select channel on registered remote control
press simultaneously the keys ∧ and ∨ – the drive makes
a short up-down movement
once again press simultaneously the keys ∧ and ∨ – the
drive will make a long confirmatory up-down movement –
all channels will be erased except for the channel of the
remote control used in the erasing procedure.
Note: all remote controls and other channels of this
remote control will be deleted.
4 Change of direction of rotation
If, after pressing the key ∧ the roller shutter moves upwards, the
direction of rotation of the drive is correct and you can proceed to
set the end positions.
If the direction of rotation is opposite, it should be changed as
follows:
press simultaneously the keys ∧ and ∨ on the remote
control – the drive makes a short up-down movement
press the key (STOP) on the remote control – the drive
makes a long up-down movement
press simultaneously the keys ∧ and ∨ on the remote
control – the drive makes a short up-down movement
Registered
Registered or new remote control
The new remote control
channel has been
registered
Select the desired
channel number
Select the desired
channel number
Remote control channels
except for the selected one
have been deleted
Select the desired
channel number
The new remote
control channel
has been
registered
