Indeeco INVIZATHERM STS-U12-0871B Manual de usuario

COMFORT HEATERS

INDEECO

425 Hanley Industrial Court – St. Louis, MO 63144 – (800) 243-8162

Fax: (314) 644-4300 – www.indeeco.com

IMPORTANT INSTRUCTIONS:

Read allthese instruc�ons before installing or using this heater.

Indeeco is interested in the safe operaof its equipment. All wiring to this equipment

must be connected to the electrical source in strict accordance with Naonal Electrical Code

(N. E. C.) and local codes having jurisdicon.

Before installing this equipment, the user must be aware of the safety requirements as

specied by the Naonal Board of Fire Underwriters.

Do not “Box” in or further insulate the back of the on which might cause a heat buildup in

the wiring raceway. The back surface of the raceway should be at least 4 inches from

combusble material.

CAUTION: Puncture of the element face may result in a shock hazard.

This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep

combusble materials, such as furniture, pillows, bedding, papers, clothes, etc. and curtains at

least 3 feet from the front of the heater and keep them away from the sides and rear.

Extreme cauon is necessary when any heater is used by or near children or invalids and

whenever the heater is leoperang and unaended.

Do not operate any heater aer it malfuncons. Disconnect power at service panel and have

heater inspected by a reputable electrician before reusing.

To disconnect heater, turn opower to heater circuit at main disconnect panel.

Do not insert or allow foreign objects to enter any venlaon opening as this may cause an

electric shock or  or damage to the heater.

Aheater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline,

paint, or ammable vapors or liquids are used or stored.

Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause , electric shock, or injury to persons.

SAVE THESE INSTRUCTIONS

INSTALLATION:

All wiring to this equipment must be connected to the electrical source in strict accordance

with Naonal Electrical Code (N. E. C.) and local codes having jurisdicon.

Before installing this equipment, the user must be aware of the safety requirements as

specied by the Naonal Board of Fire Underwriters.

Do not install the on closer than:

4 inches to a horizontal surface

12 inches to a vercal surface

36 inches to another heater

6 feet from the oor

For wall mounng (above 6 feet from oor), outlet box and wiring raceway should always face

adjacent vercal wall mounng surface.

For angle posioning, the heater should not be directed toward any vercal surface closer than

6 feet.

IMPORTANT: When using the mounng brackets, a minimum of 4 inches should be le

between the corners of the heang secand any horizontal or vercal surface. See drawing

below.

Fig. 1 – WALL MOUNTING

Once the heater is mounted to the wall, posi the heater to the desired angle between 37°

and 53° downward from the horizontal, limited by the slot length. Tighten the two bolts to

secure the heater.

WARNING! Risk of  Do not posion any heater at an angle not allowed by

the sloed hole (37°-53°).

Do not install the on closer than:

FOR CEILING MOUNTING:

36 inches to a vercal surface for vercal mounng

4 inches to a vercal surface for angled ceiling mounng

4 inches to a horizontal surface for wall mounng

12 inches to an adjacent vercal surface

36 inches to another heater

6 feet from the oor

Fig. 2 – CEILING MOUNTING VERTICAL

Fig. 3 – CEILING MOUNTING ANGLED AWAY FROM VERTICAL SURFACE

Fig. 4 – CEILING MOUNTING ANGLED TOWARDS VERTICAL SURFACE

PROTECTED AREA MOUNTING:

A Protected Area is dened as “Located in an area that is par protected from the eects of

weathering.” Typical protected areas would be the underside of a pavilion with a roof, garage

port, and the like.

FOR PROTECTED AREA WALL MOUNTING:

Adhere to all requirement for mounng listed above. Addinally:

Do not install the on closer than 18 inches to edge of overhang of roof and no more

than 7.25 inches (to top of bracket) below the edge.

The heater needs to be installed in a posiuch that it is protected from rain, snow, and

similar outdoor wet areas.

Fig. 5 – PROTECTED AREA MOUNTING

FOR PROTECTED AREA CEILING MOUNTING:

Adhere to all requirement for Ceiling Mounng listed above. Addinally:

Do not install the on closer than 18 inches to edge of overhang of roof.

The heater needs to be installed in a posiuch that it is protected from rain, snow, and

similar outdoor wet areas.

Fig. – PROTECTED AREA CEILING MOUNTING

For supply connecns use the wire size (or larger) as directed by the chart below. All wires

must be suitable for at least 75°C (167°F).

MODEL NUMBER 120 VOLT

AWG. WIRE SIZE

208/240 VOLT

AWG. WIRE SIZE

277 VOLT AWG.

WIRE SIZE

480 VOLT

AWG. WIRE SIZE

STS-U12-0871B

STS-U12-1081B

STS-U12-1111B

STS-U12-1681B

STS-U12-1436J - 14 - -

STS-U24-1015V

STS-U24-1316B

STS-U24-1659B 12 - - -

STS-U24-2192B

STS-U24-2222B

STS-U24-3363B 8 - - -

STS-U24-1297V

STS-U24-1701V

STS-U24-2001V

STS-U24-2428V

STS-U24-3239V - 12 - -

STS-U48-2030V

STS-U48-2594V

STS-U48-3402V - 12 - -

STS-U48-4002V

STS-U48-4856V

STS-U48-6478V - 8 - -

STS-U48-2030T

STS-U48-2594T

STS-U48-3402T - 12 - 14

STS-U48-4002T

STS-U48-4856T

STS-U48-6478T - 8 - 12

STS-U48-3964N - - 12 -

STS-U48-4776N

STS-U48-6056N

10-- -

- - -

- - 14

- -

- 14 - -

- -

14 - - -

SUPPLY CONNECTIONS

- -

10 -

14 -

12 -

To reduce the risk of , do not store or use gasoline other able vapors and liquids in the

vicinity of the heater.

CAUTION – High temperature, risk of re, keep electrical cords, drapery, furnishings, and

other combusbles at least 6 feet (0.9 m) from the front of the heater and away from the side

and rear.

MODEL NUMBER

120 VOLT

AWG. WIRE SIZE

208/240 VOLT

AWG. WIRE SIZE

277 VOLT AWG.

WIRE SIZE

480 VOLT

AWG. WIRE SIZE

STS-U24-1992P

STS-U24-2442P

STS-U24-3041P

STS-U48-3971P

STS-U48-4794P

STS-U48-5954P

STS-U48-3928U

STS-U48-4838U

STS-U48-6060U

14 - -

12- - -

- - -

SUPPLY CONNECTIONS

WIRING DIAGRAMS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Indeeco

Indeeco

Indeeco 931 F Series Manual de usuario

Indeeco

Indeeco 907 Series Manual de instrucciones de instalación

Indeeco

Indeeco IUH Series Manual de usuario

Indeeco

Indeeco Invizatherm Thin Series Manual de usuario

Indeeco

Indeeco 908X Series Guía

Indeeco

Indeeco 961 Series Manual de usuario

Indeeco

Indeeco 350 SERIES Instrucciones de montaje

Indeeco

Indeeco process Instrucciones de montaje

Indeeco

Indeeco 781 SERIES Instrucciones de montaje

Indeeco

Indeeco ZCA Series Instrucciones de montaje

Indeeco

Indeeco WHI Series Manual de usuario

Indeeco

Indeeco 905 Series Guía

Indeeco

Indeeco UCI Series Manual

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario