INCRA CLEANSWEEP DOWNDRAFT DUST COLLECTION CABINET OWNER’S MANUAL
Manufactured by Taylor Design Group, Inc. P.O. Box 810262 Dallas, TX 75381 WWW.INCRA.COM
Page 2
3. Remove any existing router plate or router
lift and router from your router table then turn
the table upside down for ease of assembly.
Position the downdraft on the underside of the
table centered on the table opening. The Blast
Gate Slide pull tabs should be oriented facing the
infeed side of the table. Using the CleanSweep as
a template, mark the (8) mounting hole positions
with a pencil then follow the instructions below
that match your table type, either Laminate
covered MDF or Solid Phenolic, using
fasteners from Hdwr. Pack E-09.
Note: If your router table includes corner
mounted levelers such as those shown in Fig. 4,
installation will require the CleanSweep Adaptor
(sold separately). The adaptor permits use of
the corner levelers or the 10 included perimeter
levelers.
Laminate covered MDF Tables Drill 1/8”
diameter starter holes to a depth of ONLY
about 1/8”. If two of the starter holes are over
the table’s miter channel, mount the CleanSweep
using the shorter (2) #10 x 5/8” wood screws
with #10 flat washers in those two holes and
the longer (6) #10 x 3/4” wood screws with
washers in the remaining mounting holes, Fig. 3.
If there are no starter holes over the miter channel, use the 3/4” long wood screws in all (8) of the holes.
Solid Phenolic Tables If two of the mounting holes are over the table’s miter channel, drill those mounting holes
with an 11/64” diameter drill bit to a depth of 7/16”. Drill the remaining (6) mounting holes to a depth of 9/16”.
Mount the CleanSweep using the shorter (2) #10-32 x 5/8” self-tapping screws with #10 flat washers over the area
of the miter channel and the longer (6) #10-32 x 3/4” self-tapping screws with washers in the remaining mounting
holes, Fig. 3. If there are no starter holes over the miter channel, all mounting holes can be drilled to a depth of
9/16” and the longer #10-32 x 3/4” self-tapping screws can be used in all (8) of the holes.
ASSEMBLE AND ATTACH CLEANSWEEP TO ROUTER TABLE
Fig. 1 Assemble Two Halves
12 ea. 10-32
Hex Nut
1. Screw the two halves of the CleanSweep together using 12 each of the 10-32 x 5/8” Phillips machine screws
with lock washers and hex nuts from Hdwr. Pack E-08 as shown in Fig. 1.
12 ea. #10
Lock Washer
12 ea.
10-32 x 5/8”
Phillips
Machine Screw
Fig. 2 Install Blast Gate Slide
Push Blast Gate
Slide Into Clean-
Sweep
2 ea. 10-32 Hex Nut
2 ea. #10
Lock Washer
1 ea. Plastic
Stop Gasket
2 ea. 1/64”
(thin)
Washer
2 ea.
10-32 x 5/8”
Phillips
Machine
Screw
2. Insert the Blast Gate Slide through the slotted hole at the end of the CleanSweep assembly and attach the plastic
stop gasket using 2 each of the 10-32 x 5/8” Phillips machine screws with thin washers, lock washers and hex nuts
as shown in Fig. 2.
Fig. 4 CleanSweep Adaptor
CleanSweep Adaptor (sold sep-
arately) required for Non-INCRA
tables with Corner Levelers Corner Levelers
(Kreg and JessEm MDF tables)
Fig. 3 Screw CleanSweep to Underside of Router Table
8 ea. #10x3/4” Wood
Screws (MDF tables)
or
8 ea. #10-32x3/4”
Self-tapping Screws
(Phenolic tables)
8 ea. #10 Washer
Miter Channel
CAUTION: If directly over
Miter Channel, use the
shorter pilot hole depth and
5/8” screws in these
2 holes as described in
Step 3
