Impact Test Equipment BA165 Manual de usuario

User Guide

BA165

Electronic Balance 6000g x 0.1g

Impact Test Equipment Ltd

www.impact-test.co.uk & www.impact-test.com

Impact Test Equipment Ltd.

Building 21 Stevenston Ind. Est.

Stevenston

Ayrshire

KA20 3LR

T: 01294 602626

F: 01294 461168

E: [email protected]

Test Equipment Web Site

www.impact-test.co.uk

Test Sieves & Accessories Web Site

www.impact-test.com

CONTENTS

1. INTRODUCTION................................................................................................. 2

2. LOCATING THE BALANCE............................................................................... 2

3. TECHNICAL DATA............................................................................................. 3

4. INSTALLATION.................................................................................................. 4

5. INDICATORS & KEY FUNCTIONS .................................................................... 4

6. INTERNAL BATTERY ........................................................................................ 5

7. OPERATION....................................................................................................... 5

7.1 POWER ....................................................................................................... 5

7.2 WEIGHING .................................................................................................. 6

8. FUNCTION MENU.............................................................................................. 6

8.1  = Display Averaging Rate.................................................................... 8

8.2  = Digital Filtering Selection.................................................................. 8

8.3  = Baud Rate Selection ........................................................................ 8

8.4 = Parts Counting Function................................................................ 9

8.5  = Calibration Procedure ................................................................ 11

8.6 = Results Printed Automatically or Manually.................................. 11

8.7  = Print when stable or instantaneous............................................. 12

8.8 = Autozero Function........................................................................... 12

8.9 



= Automatic Power Switch Off............................................................ 13

8.10  = Hold Maximum Value ...................................................................... 13

8.11  = Newton Unit of Weight ..................................................................... 14

8.12  = Display the battery Voltage.......................................................... 14

9. COMMUNICATION WITH A COMPUTER OR PRINTER................................. 14

9.1 RS-232 Communication........................................................................... 14

10. ERROR MESSAGES .................................................................................... 16

1. INTRODUCTION

•The ADG series of precision electronic balances offers a range of

capacities from 3000 grams to 10 kilograms.

•The balances are very simple to use and are applicable for general

weighing. The user can also use the parts counting and weighing

functions for special applications.

•The balances have an internal rechargeable battery.

•Special functions are available for parts counting, check-weighing,

displaying weight in Newtons and displaying holding a maximum

weight.

•The standard RS-232 interface allows the weight to be sent to a

computer or printer and allows control of the balance using

commands from a PC.

2. LOCATING THE BALANCE

•Place the balance on a stable surface.

•The ambient temperature of the balance should be kept as constant as

possible. Do not place the balance where it may be subjected to draughts

or heater. It is advisable not to place the balance near windows, air

conditioning vents or radiators.

•The balance should be placed in a location where it is not likely to be

damaged by accidentally dropping heavy weights or moisture on to the

balance. The weighing area should be kept clean.

•Protect the balance from vibration, temperature and dust.

3. TECHNICAL DATA

SPECIFICATIONS

ADG 3000

ADG 6000

ADG 10

Maximum weighing

capacity (Max) 3000g 6000g 10000g

Tare range - 3000g -6000g -10000g

Interval d= 0.1g 0.1g 0.2g

Verification scale interval

e= 1g 1 g 1g

Operating temperature +5ºC / 35ºC

Internal Battery 12VDC, approximately 20 hours operation

Power supply 14VDC, 100mA minimum

Supplied from external power supply

230VAC or 115VAC 50/60Hz.

Pan Size (mm) 160 x 160 mm

6.3 x 6.3 inches

Net weight 2.6 Kg / 5.7 lb.

Standard features RS-232 Interface, Bi-directional

Special functions Parts Counting, Check-weighing to Low and High Limits

4. INSTALLATION

•Unpack the balance carefully.

•Place the rubber bumpers for the pan support on the pins then lay

the pan on the supports. The spring under the permanent pan

support will help eliminate static electricity that may accumulate on

some samples.

•Turn the adjustable feet until the balance is level (check the bubble

level on the rear of the balance).

•Insert the power supply connector in the plug on the rear of balance.

Plug the power supply into the mains supply.

•Press the [On/Off] key to activate the balance.

•Wait until the balance auto-test is finished and a stable zero is

displayed.

5. INDICATORS & KEY FUNCTIONS

INDICATORS





On, when balance is at zero



On, when the display is stable



Indicates a low battery condition



Indicates when the balance is in parts counting mode





Indicates when the balance is in grams weighing mode

Three bars on the left of the display are used for check-weighing to show

if weight is below the low limit, above the high limit or between the limits.

KEYS

KEY Primary Function Secondary Function

[Tare]

Re-zeroes the display to

eliminate weight of containers

Selects the active digit when setting

parameters. Return to normal

weighing after parts counting,

check-weighing or percent weighing

[0]Sets new zero point

[Func]

Enters the Function Menu

Selects or accepts a parameter

[Print]

Sends data to the RS-232

interface

Changes value of a parameter

[On/Off]

Switches the power to on and off

6. INTERNAL BATTERY

The ADG balance includes a 12 Volt lead acid internal battery as standard. This

battery will allow approximately 20 hours of operation from a full charge. The

balance can be charged overnight using the external power supply. If the

display shows “” the battery should be charged.

Only the power module supplied with the balance should be used for charging

the battery. Incorrect power supplies could damage the battery or circuit boards

and may cause the battery to leak acid.

. OPERATION

7.1 POWER

•Press the [On/Off] key to turn the balance on.

•All LCD segments will be on for few seconds and then the display

will show “”.

•After some time it will show zero weight. The stable (STAB) and

Zero (ZERO) indicator will be on.

7.2 WEIGHING

•If necessary press the [Tare] key to zero the display. Place the

object to be weighed on the pan and read the weight after the

stability indicator (STAB) is displayed.

•The Zero function only operates within a narrow range (±4% of the

capacity of the scale) around the original zero point. If the zero

value is too large the error message “ ” will be shown. In this

case use the [Tare] key to zero the display.

•When you use a container you can set the display to zero so that

only the net weight of any items added to the container is shown.

Place the container on the pan and press [Tare].

•When items are put into the container, the display will only show the

weight of the items, which is the net weight.

•This may be repeated as many times as necessary to add more

items to the container. Each time only the weight of the new addition

will be shown.

•Make sure that the weight of the container and contents do not

exceed the maximum capacity of the balance. Display will show

"" if the capacity is exceeded. It will show “” if more weight

is added above the “” point.

8. FUNCTION MENU

The function menu has a number of functions that allow the user to configure

the balance as required. The user can select functions to calibrate the balance,

select last digit suppression, select parts counting, set RS-232 parameters and

enable the check-weighing function.

•Press the [Func] key to select the function. Then follow the

instructions for the function selected.

•Not all functions may be available on all balances. Refer to your

dealer or Adam Equipment for further details.

The following functions are available. For details on how each function is used

refer to the respective sections.

 !

Set the display averaging

!

Set the digital filtering

!

Set the baud rate- adjustable from 300 to 9600 baud

!

Enter parts counting function

!

Enable check-weighing function and set the low and high limits

!

Enter calibration mode

!

Auto or manual print

!

Print instantaneously or only when stable

!

Enable the auto zero function

!

Enable the automatic power-off function

!

Set the balance to hold the maximum value function

!

Display Newtons function

!

A measure of the power supply voltage

PROCEDURE

•To enable or disable a function, press [Func].

•Press [Print] to view the current setting.

•Pressing [Print] again will change the setting to the next value.

•Pressing [Func] again will return to normal weighing.

•To scroll through other functions, keep pressing the [Func] key

when the scale is in the weighing mode.

•Press [Print] to enter the desired function or press [Func] to go to

the next function.

8.1  = Display Averaging Rate

•Select the required averaging rate for the display update.

•Press the [Func] key until “” is displayed.

•Press [Print] to view the current setting.

•Press [Print] again to select the desired value.

•Press the [Func] key to return to weighing.

“” = Fastest display rate for applications such as filling.

“"” = Slowest display rate for applications such as animal

weighing or unstable environment.

8.2  = Digital Filtering Selection

•Select the required level of digital filtering.

•Press the [Func] key until “” is displayed.

•Press [Print] to view the current setting.

•Press [Print] again to select the desired value.

•Press the [Func] key to return to weighing.

“” = Lowest level for normal use.

“” = Highest level for uses in unstable environment

8.3  = Baud Rate Selection

•Select the required baud rate for the RS-232 communications.

Default rate is 4800*.

Tabla de contenidos

Otros manuales de Escala de Impact Test Equipment

Impact Test Equipment

Impact Test Equipment Harvard Trip BA710 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario