imilab V1 Manual de usuario
V1 Vacuuming Robot
User Manual
Manufacturer: Shanghai Imilab Technology Co., Ltd.
Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road, Minhang District,
Shanghai, China
For further information, please go to www.imilab.com.
Support: [email protected]
Scan the QR code with your mobile phone
to get the manual in more languages
Contents
Introduction·······························
Installation································
Operation··································
Connecting to Wi-Fi······················
Daily maintenance························
Basic parameters·························
Troubleshooting··························
Frequently asked questions············
Precautions································
1
8
9
13
14
23
24
25
27
Please read this manual carefully to ensure correct and safe
use of the product.
Maintenance notes
Repairs should only be done by professionally trained and
qualified technicians.
Do not attempt to perform any repair on your own to avoid
serious consequences.
In case of a malfunction, please refer to the “Troubleshoot-
ing” and “Frequently Asked Questions” sections before
contacting customer service.
If you are unable to troubleshoot the fault, please unplug the
power cable and contact us.
Please read this manual carefully to ensure correct and safe
use of the product.
Please read this manual carefully before using the product and
keep it in a safe place for future reference. The adapter of the
product is intended for use up to a maximum height of 2,000
meters above sea level.
Introduction
1 2
Smart recharge
Short press the button to activate smart
recharge.
Slow flashing yellow light indicates that the
product is recharging or the battery is
running low.
The blue breathing light indicates that the
product is in charging.
Reset button:
Short press (less than 3 seconds) to force
shut down the product
Power on/o
or Whole map cleaning
Infrared receiving sensor
Short press to start/pause cleaning.
Press and hold for 3 seconds to power on/o.
The solid blue light indicates that network
connection is successful/product is working
normally/in standby. The blue breathing
light indicates that the product is being
powered on.
Slow flashing blue light indicates that the
firmware is being updated/restoring to
factory settings.
Flashing blue light indicates that network
is being connected.
The red breathing light indicates that the
battery is low.
Flashing red light indicates abnormal status.
Light o indicates that the product is
powered o/in sleep mode.
Network settings
While the product is powered on,
press and hold the and buttons
together for 5 seconds. After hearing
“Entering network settings” voice,
release the buttons to enter the
Network settings.
While the product is powered on,
press and hold the buttons
together for 10 seconds. After hearing
“Factory settings will be restored”
voice, continue to hold the buttons for
another 10 seconds to restore the
product to factory settings.
3 4
Main body and sensors
Lidar
5
4
5
3
1
1Cover
2
Collision sensor
5
Button
3
Charging plates
6
Infrared receiving
sensor
4
Directional wheel
7Side brush
8
Roller brush
11
Cliff sensors
9
Left wheel
12
Middle brush cover
10
2-in-1 dust box and water tank
14
Right wheel
13
2
6
14
9
9
9
7
8
11
10
12 13
5 6
Water inlet
Water tank
Dust box
Dust box release button
Dust box catch
Mop cloth holder
Mop cloth
Filter cover
Filter
2-In-1 water tank Dust collection dock
(dust collection and charging 2-in-1)
Cover
Open the cover to put
in/take out dust bag
Indicator light
Dust bag chamber
Infrared lens
Charging and dust
collection sensor head,
dust collection sensors
The light will shine brightly when the dust bag is full.
The light will flash if the dust bag is not installed
correctly.
The light will flash brightly during dust collection.
When the battery is fully charged, two green bars will
be shown. When the battery is at 50% or lower, one
green bar will be shown.
Dust inlet
The dust in the product
will be transferred to
the dust bag via the
dust inlet
7 8
Installing the dust collection dock
1. Place the dust collection dock against a wall and on a level surface.
Plug in the power cable to a compliant socket and turn on the power.
2. Ensure that there is no object within 1.2 meters in front of the dust
collection dock and within 0.5 meters of its sides.
Installation
Fan filter Place it against a wall
Dust bag
handle
Dust bag
Dust bag (the dust collection dock is already installed with 1)
Reminder: The dust bag is a consumable material and cannot
be reused. Please replace it regularly.
1. Powering on/o
Press and hold the “ ” button for 3 seconds to power on the
product: when the blue indicator light flashes slowly for 4 seconds
and becomes solide, the robot vacuum has entered standby mode.
When the robot vacuum is still, press and hold the “ ” button
for 3 seconds to power it off. The indicator light will turn off.
The robot vacuum will enter sleep mode when it is not used for 20
minutes. Short press any button to wake the robot vacuum up from
the sleep mode.
Note: The robot vacuum cannot be powered on and will not enter
sleep mode while it is being charged.
9 10
2. Cleaning
While the robot vacuum is powered on, short press the “ ”button
and the robot vacuum will say “Start cleaning”. While the robot
vacuum is cleaning, short press the “ ” button and the robot
vacuum will stop cleaning.
Note: The robot vacuum will not start cleaning when the battery level
is too low.
3. Automatic/manual recharge
After completing a cleaning operation, the robot vacuum will
say “Cleaning completed. Returning to recharge.” The robot
vacuum will automatically return to the stand to recharge.
When the battery is running low, the robot vacuum will
automatically return to the stand to recharge.
4. Refilling the water tank or adding mop cloth
while cleaning
Short press the “ ” button to stop the robot vacuum. Remove
the mop module. Add water or mop cloth. Re-insert the mop
module and short press the button again to continue cleaning.
5. Network connection and firmware update
Scan the QR code on the robot vacuum to download the app.
Open the app and follow the on-screen instructions to connect
to a Wi-Fi network. Refer to the quick guide for more information.
Use the app to check for the latest firmware and update it. While
updating the firmware, ensure that the robot vacuum is being
charged and has at least 50% of battery left. Follow the
on-screen instructions in the app for firmware update. After
downloading the app, open it and follow the on-screen
instructions to connect to a Wi-Fi network. After the robot
vacuum is connected to a network, you can use the app to
control the robot vacuum remotely or schedule a cleaning.
6. Fault status
In case of a fault during operation, the robot vacuum will read
an error message and its indicator light will flash quickly in red.
Refer to the “Troubleshooting” for the problem solving approach.
After encountering a fault, the robot vacuum will enter sleep
mode when it is not operated for 10 minutes.
Using the robot vacuum
1. Please the robot vacuum on a level indoor surface. Remove
the safety strips on both sides of the front bumper.
Operation
Remove
11 12
3. Wet the mop cloth and attach it to the Velcro. Fill water using
the water inlet and insert the rubber cover securely.
2. Press the dust box release button to remove the 2-in-1 dust
box and water tank. When using the 2-in-1 water tank for the
first time. The water tank may contain a very small amount of
water, left behind after a production test. This is normal.
4. Insert the 2-in-1 dust box and water tank into the robot
vacuum.
Note:
1. When the robot vacuum returns to the dust collection dock
after at least 1 minute of cleaning. The dock will automatically
clear the dust box. While the dust is being collected, a green
arrow will flash brightly on the display.
2. The robot vacuum may not start when its battery is too low.
Please fully charge the robot vacuum before using it.
3. When the battery is running low during a cleaning operation,
the robot vacuum will automatically return to the dust collection
dock to recharge. After it is charged, the robot vacuum will
return to the original spot to continue cleaning.
5. Press and hold the “ ” button for 3 seconds to power on
the robot vacuum. Short press the “ ” button to return the
robot vacuum to the stand. The robot vacuum will enter
standby mode after it is fully charged.
13 14
Login to the Mijia app for more
device control and shop for more
smart products.
Mijia app
App download
Search for “Mijia” in an app
store or scan the QR code to
download the app. Open the
app.
Wi-Fi connection for Android
phones
Open the notification to connect to the product.
Tap”next” and follow the on-screen instructions.
Resetting Wi-Fi connection
When there is a need to reset the Wi-Fi connection due to a change
of router or Wi-Fi password, press and hold the “ “ and “ ”
buttons together for 10 seconds. Wait for the Wi-Fi indicator light to
flash quickly in blue. You will hear a voice prompt when the Wi-Fi
connection is reset successfully.
Wi-Fi connection for iOS phones
Enter the phone’s Wi-Fi settings page. Select the robot vacuum’s
hotspot and wait for a connection to be established. Return to the
app, tap next and follow the on-screen instructions.
Note: If you are unable to connect your phone to the robot vacuum,
please see “Resetting Wi-Fi connection” below. Connect the
produce to a Wi-Fi network for better usage experience.
Using the Mijia app
This product is part of the Mijia product family and can be controlled
using the Mijia app. It can interact with other Mijia products.
Note: Actual operation may differ due to Mijia app update. Please
follow the on-screen instructions of the Mijia app.
“Works with Mijia” only involves a verification at a software level.
Xiaomi and Mijia are not responsible for the production processes,
standards execution, quality supervision, etc. of the product and the
manufacturer.
Scan the QR code to download and install the Mijia app. Open the
app to enter the device connection page. Alternatively, search for
“Mijia” at an app store to download and install the app. At the app
homepage, tap the “+” button at the top right hand corner and
follow the on-screen instructions to add a device.
Connecting to Wi-Fi
Cleaning the 2-in-1 dust box and water tank
1. Press the dust box release button and pull out the 2-in-1 dust box
and water tank.
Daily maintenance
2. Open the dust box catch and remove the filter cover.
15 16
5. Add clean water to the dust box and close the cover. Shake the
dust try and pour out the dirty water. Repeat a few times until the
dust box is clean.
6. Flip the 2-in-1 dust box and water tank over and replace the mop
cloth or remove it for cleaning.
Note:
1. Cleaning effect will deteriorate when the mop cloth is dirty. Please
clean it regularly.
2. Please remove the mop cloth before cleaning it. Do not wash the
mop cloth while it is attached to the 2-in-1 water tank. Otherwise,
the 2-in-1 water tank may be damaged.
3. It is recommended to replace the mop cloth every 6-12 months to
ensure cleaning effect.
3. Take out the filter.
4. Use a brush to clean the filter and filter cover.
Filter cover
Filter
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
