Imi Heimeier Boost V2 Manual de usuario
Boost V2
2
Hereby, IMI Hydronic Engineering declares that the radio equipment type
(designation of type of radio equipment) is in compliance with Directive 2014/53/EU.
RF Frequency: 868 MHz 2 dBm, 2.4 GHz 3.5 dBm.
Hiermit erklärt IMI Hydronic Engineering, dass der Typ der Funkanlage (Bezeichnung
des Typs der Funkanlage) mit der Richtlinie 2014/53/EU übereinstimmt.
HF-Frequenz: 868 MHz 2 dBm, 2,4 GHz 3,5 dBm.
Par la présente, IMI Hydronic Engineering déclare que le type d’équipement
radio est conforme à la directive 2014/53/UE.
Fréquence RF : 868 MHz 2 dBm, 2,4 GHz 3,5 dBm.
3
EN
Boost – LED/button indication........ 4
Installing the Boost ......................... 5
Using the Boost with the wireless
series system.................................. 6
Using the Boost with the neoHub
system............................................ 7
Wiring diagram - Boost................... 8
Factory resetting the Boost............. 9
DE
Boost – LED-/Tastenanzeige......... 10
Installation .................................... 11
Verwendung mit der Wireless-Serie...12
Verwendung des Boost mit dem
neoHub-System ........................... 13
Anschlussschema - Boost............ 14
Auf Werkseinstellungen
zurücksetzen ................................ 15
FR
Boost – Indications des LED/
boutons........................................ 16
Installation du Boost V2................ 17
Utilisation du Boost avec le
système sans fil ............................ 18
Utilisation du Boost avec le
système neoHub ......................... 19
Schéma de câblage - Boost ......... 20
Réinitialisation d’usine du Boost ... 21
Notes/Notizen/Notes .................... 22
4
Boost – LED/button indication
RF repeater
LED’s
(RX TX Comms)
Pairing
button
Power
status LED
Neo/Mesh repeater LED’s
(Link )
1
5
• Using a small screwdriver, slightly
loosen the screw located at the
base of the Boost. You can then
carefully separate the front panel
from the back plate.
• Position the Boost back plate on
the wall, fixing into place using the
screws provided.
• Terminate the cables to the Boost
as shown in the wiring diagram
(section 5).
• Mount the front panel onto the
back plate, tighten the retaining
screw on the base.
• Switch on the power supply, the power LED will illuminate.
Installing the Boost2
6
4
4
3
3
2
2
1
1
ON
ON
The IMI Heimeier Boost is a repeater designed to extend the communication
distance of the neoAir thermostat to the UH8-RF V2 wiring centre.
On the Boost, set switch number 3 to the OFF position
The Boost repeater does not need to be paired to any
devices on the system.
Signals that are being transmitted by the thermostats will be detected by the
Boost and repeated on to the UH8-RF V2.
3Using the Boost with the wireless series system
7
44332211
ONON
The IMI Heimeier Boost is a repeater, designed
to extend the communication distance between
neoStats, neoAirs and the neoHub.
On the Boost, set switch number 3 to the OFF position
First pair the Boost repeater to the neoHub, then pair any other devices which
require the help of the Boost to communicate with the neoHub.
Signals that are being transmitted by the thermostats will be detected by the
Boost and repeated to the neoHub.
Add the Boost repeater from the Home screen in the Neo App;
Select +
Add Accessory
Add Repeater
Then follow the pairing instructions in the app.
Using the Boost with the neoHub system
4
8
Wiring diagram - Boost
LEN
230 V supply
3A
5
9
Factory resetting the Boost
To reset the Boost;
Press and hold the connect button for 10 seconds,
The light on the Boost will now flash.
Release the connect button.
Once the light has stopped flashing, the reset procedure is complete.
6
10
Boost – LED-/Tastenanzeige
Stromver-
sorgungs-
anzeige
Neo/Mesh-Verstärker-LEDs
(Link )
Funkver-
stärker LEDs
(RX TX Comms)
Kopplungs-
taste
1
Tabla de contenidos
Idiomas:
