be chosen di scr et i onar i l y,
4. The t ur n val ve of t he machi ne is made up of we a r a b l e , aci d-resistant, heat -resistant F- 4.
Do n o t b e a t , h i t i t wh e n wa s h i t .
Par t Fo ur : I ns t al l me nt a nd Debuggi ng
1. Put t he hopper ( pi c. 1) over t he t hr ee -wa y c o n t a c t b i g s q u a r e b o d y cont rol val e, and l ock
the connect par t wi t h Ar mf u l Ho o p.
2. I nst al l t he f i l l i ng nozzl e 01( pi c. 1) , connect t he bi g s quar e body por t and t he f i l i ng head
por t wi t h pr oduct f eedi ng t ube. l ock i t wi t h cl amp.
3. Conf i r m t he pos i t i on of t he r eed swi t ch( t he posi t i on of t he back r eed s wi t ch i s f i xed)
4. Connect wi t h t he el ect r i ci t y power and t ur n on t he el ect r i ci t y power swi t ch.
5. Connect wi t h t he ai r sour ce and t ur n on t he ai r s our ce s wi t ch.
6. Swi t ch t he wor k model t o manual , cont r ol t he f i l l i ng by pedal .
7. Adj us t t he t hr ot t l e 1( 05) and t hr ot t l e 2( 06) t o a sui table pr oduct suck and f i l l i ng s peed.
To ge t a b e t t e r wor k e f f i c i e n c y, c a n f a s t e r t h e p r odu c t s u c k s p e e d 0 6 , a n d s l owe r f i l l i n g s pe e d
05( i f t he f i l l i ng s peed i s t o f as t wi l l make t he pr oduct or bubbl e das h out of t he bot t l e,
affect t he fi l l i ng qual i t y. )
8. When adj ust t he fi ling range,
Slide the front reed switch to range you asked then fix it.
9. Put t he pr oduct to hopper, begi n f i l i ng.
10. When wor ker s ar e pr of i ci ent i n i t , can s wi t ch t he wor k model t o aut omat i c t o i mpr ove wor k
effi ci ency.
Par t Fi ve : Saf e Ope r at i on
The ma c hi n e i s us e d t o f i l l pa s t e , no o t h e r us a g e . To i s s u r e a s a f e o pe r a t o n , p l e a s e not e :
1. The machi ne adopt al t er nt i on cur r ent 220V, 1A, ai r pr es s ur e 4-6KGS.
2. Bef or e t ake apar t and cl ear t he machi ne, must cut of f t he el ect r i ci t y power and ai r s our ce.
3. When cl ear t he machi ne, can not use the wa t e r r i n s e t h e ma c h i n e b o d y d i r e c t l y i n c a s e des t r oy
the machine electricity contorl part inside.
4. For safet y of person, the machine need to be earthing properly.
5. When i ns pect t heel ect r oci r cui t ( pi c. 3) of t he machi ne, mus t cut of f t he el ect r i ci t y power and
ai r source fi r st .
Par t Si x: Ma c h i n e Mai nt ai n
1. The ma c hi n e s u r f a c e i s s t a i n l e s s s t e e l , whe n c l e a r t h e ma c h i n e , d on’t use sharp and hard
tools to scratch the surface.
2. Ca n u s e al cohol to clean the dirt on the surface of the machine.
3. Cy l i n d e r h a s been l ubr i cat ed i n t he factory, so no need di s as sembl y and
